MEEC TOOLS 015273 1300 W-80 l-min Garden Pump Instruction Manual

MEEC TOOLS 015273 1300 W-80 l-min Garden Pump

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision.
• Familiarise yourself with the controls on the product and how to use them. Read all the instructions and safety instructions before use. Failure to follow all the instructions and safety instructions can result in a risk of electric shock, serious personal injury and/or material damage.
• Contact the retailer or qualified personnel if you have any problems or questions.
• Store these instructions so that they are readily available for everyone who uses the product. These instructions should be enclosed with the product if it is sold or passed on.
• Do not make any modifications to the product. Only use accessories recommended by the manufacturer.
• The product must only be used for its intended purpose and in accordance with these instructions. The product must only be used for its intended purpose and in accordance with these instructions, otherwise there is a risk of personal injury and/or material damage.
• The manufacturer cannot accept liability for personal injury and/or material damage resulting from improper use.
• A damaged power cord or plug must be replaced by an authorised service centre, or other qualified personnel, to ensure safe use.
• Do not use the product if it is damaged. Always check the power cord, plug and casing before use. If the product is damaged, or not working properly, it must be repaired or discarded.
• Pull out the plug immediately if the power cord or product gets damaged or stops working properly, otherwise there is a risk of electric shock.
• Repairs must be carried out by qualified personnel. Imperfect repairs can result in a risk of electric shock, serious personal injury and/or material damage.
• Do not pull the power cord to pull out the plug.
• Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces. Avoid kinking or bending the power cord.
• If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the product.
• If the product is used outdoors, only use an extension cord approved for outdoor use.
• The product is not intended to transport water for human consumption.
• Do not use the product to transport corrosive, flammable or explosive substances such as petrol or other petroleum products, nitrogenous liquids, grease, oil, salt water or waste water from toilets, or liquid that has a higher viscosity than water.
• The temperature of the pumped water must not exceed 35°C.
• Keep this product out of the reach of children.
• Do not use the product if there are any persons in the water.
• Make sure the product does not suck up aquatic animals, such as fish.
• Pay attention to the risk of contaminating the liquid as a result of leaking lubricant.
• Protect electrical connections from moisture.
• Do not expose the product to temperatures below 0°C. Make sure that the product is not run without water.
• Do not pump aggressive liquids or abrasive material.
• Do not pull the power cord or float switch cord to move the product, and do not use them to secure the product from moving.
• The product is only intended for household use and is not suitable for commercial purposes.
• The manufacturer cannot accept liability for personal injury or material damage resulting from improper use.

IMPORTANT:

The product must be connected to the mains with a residual current device of max 30 mA.

SYMBOLS

TECHNICAL DATA

The declared values for vibration and noise, which have been measured according to a standardised test method, can be used to compare different tools with each other and for a preliminary assessment of exposure. The measurement values have been determined in accordance with EN ISO 3744:1995.

WARNING!

The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

DESCRIPTION

Powerful garden pump with stainless pump housing, handle and on/off button. Simple and reliable accessory for pumping clean water.

PRODUCT PARTS

1. Drain plug
2. Intake opening
3. Filler plug
4. Outlet connection
5. Handle
6. Power switch
   FIG. 1

USE

INTENDED USE

• The product is intended for semi-stationary use, for transporting clean water for watering in the home and garden, for transporting well water, rainwater and process water, and for emptying ponds and water containers etc.
• The product is not intended for continuous use.
• Only use the product in accordance with the specified conditions (see technical data).
• The product must not be used for drinking water or food.
• The product must not be used to pump explosive, flammable, corrosive or harmful substances or faeces.
• The product is only intended for household use. Always follow the safety instructions and local regulations concerning safety and the prevention of accidents.
• The product must only be used for its intended purpose and in accordance with these instructions. All other use
  is considered to be unsuitable.
  The manufacturer cannot accept liability for any damages resulting from improper use.

POSITIONING

• The product should be placed on a smooth, horizontal surface that can support the weight of the product when it is filled with water.
• To prevent vibrations the product should be placed on a rubber mat or other vibration damping underlay.
• The product should be protected from the weather in a well ventilated area.
• If the product is used for a pond or pool it should be installed in such a way as to prevent overflowing, and so that it cannot drop. Follow the applicable local regulations and directives.
• If the product is installed indoors the floor should be water resistant or provided with a floor drain.

CONNECTION OF SUCTION TUBE

IMPORTANT:

Risk of material damage. The suction tube should be installed so that it does not transfer mechanical stress to the pump.
Fit a suitable filter if the pumped water is contaminated or turbid.

NOTE:

• It is recommended to install a non-return valve to prevent return flow, which can cause the water in the product and the suction tube to empty when the product is not running.
• Use a pre-filter to protect the product from sand, clay and other particles.
• All the screw unions should be sealed with jointing tape. Any leakage will allow air to penetrate the system, which reduces the pumping capacity.
• Use teflon tape for metal threads and normal jointing tape for plastic threads.
• All parts of the suction tube should be installed by qualified personnel.
• The inner diameter of the suction tube should be at least 25 mm. The suction tube should be made of material that does not squeeze at underpressure and which is resistant to bending.
• The pump’s suction tube should be as short as possible – long suction tubes reduce the capacity of the pump.
• The suction tube should run upwards all the way to the pump, to avoid air becoming stationary in the tube.
• Make sure that the inlet on the suction tube is always under the surface of the water.

CONNECTION OF OUTLET TUBE

IMPORTANT:

Risk of material damage. The outlet tube should be installed so that it does not transfer mechanical stress to the pump.

• All the screw unions should be sealed with jointing tape. Any leakage will allow air to penetrate the system, which reduces the pumping capacity.
• Use teflon tape for metal threads and normal jointing tape for plastic threads.
• All parts of the outlet tube should be installed by qualified personnel.

WARNING! Risk of personal injury. If components are used that cannot withstand the pressure, or if the installation is not carried out correctly, the outlet tube can burst and spray out water, which can cause personal injury and/or material damage.

Note: The product is not intended for transporting drinking water, only to transport water for a toilet or washing machine.

ELECTRICAL CONNECTION

WARNING! Electrical safety! Do not expose the product to rain, or use it in damp conditions.

Prerequisites

• The plug must be plugged into a correctly installed and earthed power point.
• Check that the mains voltage corresponds to the rated voltage on the type plate and that the circuit is correctly fused.
• The product must always be connected to a residual current device with a tripping current of ≤ 30 mA when used for pools and ponds.
• If the product is used outdoors, only use an extension cord approved for outdoor use. The product must not be put in water.
• If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the product. If an extension cord is used on a reel, pull out the full length of cord.

HOW TO USE

FILLING THE PUMP HOUSING AND SUCTION TUBE WITH WATER

IMPORTANT: Risk of material damage. The product must be filled with water each time it is connected to a new installation and if the water has run out or air has penetrated into the system. Do not leave the product unattended when running. Dry running can result in material damage.

1. Remove the product from the packaging and place it on a level, stable surface. FIG. 2
2. Unscrew and remove the water filler plug and its seal.
3. Connect the suction hose to the water inlet and the outlet hose to the water outlet.  FIG. 3
4. Open the refill opening cap and fill with water until it runs over. FIG. 4
5. Replace the water filler plug and its seal and tighten.
6. The suction tube can be filled with water to shorten the suction time (only possible if the tube has a non-return valve).
7. Open the tap on the suction tube so that air can flow out during the suction time.
8. Plug in the plug and start the pump. FIG. 5
9. Switch off the product and pull out the plug when water comes out in a smooth flow. Drain the water from the product by opening the drain on the pump.  FIG. 6

NOTE:

• It is recommended to install a non-return valve between the suction tube and pump, so that the water remains in the suction tube.
• It is recommended to use an intake filter for best functionality.
• The pump and suction tube should be connected and filled with water.
• Always check before use that the suction tube is tight. Bubbles of air in the suction tube indicate leakage, and can prevent the product from working properly.

IMPORTANT: Risk of material damage. Never allow the product to run dry. Make sure there is always enough water to pump.

STARTING

1. Plug in the plug.
2. Start the product with the power switch.
3. Open the tap on the outlet tube.
4. Check that water flows out.

If the motor does not start, if the pressure does not increase or if there are other problems, switch off the product and pull out the plug, and try to correct the fault with the help of the troubleshooting guide.

IMPORTANT: Risk of material damage. Running the product for more than 3 minutes with closed outlet tube – risk of overheating and material damage.

MAINTENANCE

WARNING!

• Electrical safety! Pull out the plug before working on the product.
• Risk of personal injury. Make sure that the product and all connected devices are pressureless before working on the product.

IMPORTANT:

Risk of material damage. All the seals should be replaced if the product is dismantled.

STORAGE

If there is a risk of frost, dismantle and clean the product and its accessories and store in a frost-free place.

IMPORTANT:

Risk of material damage. The product and its accessories contain water, which means that they can burst if the water freezes.

DISMANTLING AND STORAGE

1. Switch off the product and pull out the plug.
2. Open the tap on the outlet tube and wait until all the water has run out.
3. Empty the product by unscrewing the drain plug (1) underneath the pump.
4. Disconnect the suction tube and pressure tube from the product.
5. Store the product frost-free (at least 5°C).

TROUBLESHOOTING

WARNING!

• Risk of personal injury. Repairs that are not carried out correctly can result in the risk of fatal or serious personal injury and/or material damage.
• The troubleshooting table below describes some of the most common faults and how to rectify them. Check the following points before contacting the retailer for a service.

power point and fuse.
The motor overheats because the temperature of the water is too hot.| ****

Eliminate the cause of overheating. The maximum temperature of the water is indicated in the technical data.

The motor overheats because the ventilation openings are blocked.
The residual current device has tripped.| Reset the residual current device. Contact an authorised electrician if the problem persists.
Defective motor.| Contact the retailer.
The pump does not provide enough water. Pressure too low.| Not enough water.| Check that the water level is not too low.
Suction hose leaking.| Seal the suction tube and tighten all the connections.

Suction height too high.

| Do not exceed the maximum suction height (see technical data).

The suction height should be subtracted from the delivery height.

Filter contaminated or blocked.| Clean or replace the filter.
Non-return valve blocked.| Clean or replace the valve.
Water leaking between the motor and pump, axle seal leaking.| ****

Contact the retailer.

The pump is blocked or defective.| Clean the pump with clean water and remove any blockage.

Air in the pump or suction tube.

| Fill the pump housing with water. If the suction tube has a non-return valve, fill the tube with water.
Change of suction conditions in the well (sand etc.).| Check the well and the quality of the water.
The suction tube inlet has been sucked to the underlying surface.| Use a shorter suction tube or anchor it. Use an inlet filter with a non-return valve.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>