EUROLAMP 2531-23 Blue Flame 3.8kw Regulator Gas Heater Instructions

EUROLAMP 2531-23 Blue Flame 3.8kw Regulator Gas Heater

Product Information

Specifications

• Model: 2531-23
• PIN Code: 1336CU010
• Product Code: 920-29678 (DA-303BF)
• Brand: Diamond (Zhongshan) Electrical Appliances Co., Ltd
• Gas Type: Butane (G30) at 28-30mbar, Propane (G31) at 37mbar
• Heat Output: 3.8 kW (276g/h)
• Efficiency: EEI = 90%

FAQ

• Q: How do I ignite the pilot flame?
  • A: Turn the gas knob to the pilot position, press it down, and ignite using a suitable igniter.
• Q: What should I do if the heater malfunctions?
  • A: If you experience any issues, turn off the gas supply immediately and contact a qualified technician for assistance.

Please read these instructions carefully. Please pay particular attention to the safety information. We recommend that you keep the instructions for future reference.

SAFETY RECOMMENDATIONS

• It is essential to read and understand all the safety and operating instructions before the installation. If this is your first time using the device, keep the instructions secure for future reference.
• In cases where the connection to a direct power supply needs to be made, it is necessary to be done by a qualified person.
• It can be cleaned with a dry and clean fabric or with a use of neutral detergent. Do not use solvents or corrosive products. In case that the surface is wet, wait until it gets dry and then use it. Avoid contact on all electrical parts with liquids.
• The device should be kept out of the reach of children and minors.
• The warranty is no longer valid when there are defects in the product where come from damages or when the parts of the product has been damaged by unauthorized persons as well as after any intervention on the device due improper handling or misuse.
• Follow the instructions below for safe use and installation. As you unpacking the product, check for damages. In that case, please inform your supplier.

ATTENTION: Electrical connections must be made by a qualified electrician and in accordance with European rules for electrical installations.
IMPORTANT: THE COMPANY IS NOT RESPONSIBLE FOR THE INSTALLATION. INSTALLATION IS THE SOLE RESPONSIBILITY OF THE CUSTOMER.
CAUTION: Before installing the device, be sure to turn off the power supply. Do not turn on power until the device is fully installed and ready for use.

EUROLAMP SA reserves the right to interpret and amendment the content of this document at any time without prior notice.

CORRECT DISPOSAL OF THIS PRODUCT

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Specifications

MOBILE GAS HEATER|
---|---
Model| DA-303BF
Trade Name| 920-29678
Appliance Category (Cat.)| I3+(28 ~ 30/37)
Pressure| (28 ~ 30/37) mbar
Size of injector (mm)| 0.97 mm
Type of Gas| Butane (G30) at (28 ~ 30)mbar Propane (G31) at 37mbar
Total heat input (ΣQn)| 3.8 kW (276g/h)
Countries of Destination| LU, NL, DK, FI, SE, CY, CZ, EE, LT, LV, MT, SK, SI, BG, IS, NO, TR, HR, RO, IT, HU, GR
Gas Container| up to 15kg
Producer| Diamond (Zhongshan) Electrical Appliances Co., Ltd

This product is not suitable for primary heating purposes

• The energy efficiency class: Class A
• The direct heat output: 3,8 kW
• The energy efficiency index: EEI = 90%

Please refer to the instruction manual for the assembly, installation, maintenance, disassembly, recycling and/ or disposal at end-of-life.

This heater is in conformity with following EC directive and Regulations

• (EU)2016/426(GAR) Regulation on appliances burning gaseous fuels
• Commission Delegated Regulation (EU) 2015//1186 and 2015/1188

And that the following harmonised standards have been applied: EN449:2002 + A1:2007

FOR YOUR SAFETY PLEASE READ THIS MANUAL CAREFULLY AND OPERATE THE APPLIANCE ACCORDING TO THESE INSTRUCTIONS.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
ONLY USE IN A WELL VENTILATED AREA.

Product Introduction

The heating system works with gas power, which will meet with demands of customers’ choose of gas supplying. This ceramic gas-fired heater is designed for room heating and creation of comfortable atmosphere in cold season. The heater can be installed only in vertical position in well ventilated rooms. This heating appliance is handy and simple in installation, efficient and economic in use thanks to minimum losses, high heat output and maximum comfortable distribution of heat flow.

Important Information

• Please carefully read the Operation Manual before using the heater.
• This Operation Manual contains the important information on your safety as well as some recommendations on proper use of the appliance and its maintenance.
• Keep the Operation Manual along with the warranty certificate, sales receipt, and if possible, cardboard package and packing material.
• The purchased heater may somewhat differ from one described in the Manual, but this does not affect the methods of use and operation.

Important precautions and instructions given in this manual do not include all possible modes and situations, which can be encountered. It is necessary to understand that common sense, cautiousness, and carefulness are the factors, which cannot be “integrated” to any product.

These factors should be considered by the person, who is interested in proper operation of the device. The manufacturer is not responsible for damage of the appliance or its components during transportation, as a result of incorrect installation, as a result of voltage surges, as well as in the event of changes or modifications in any part of the appliance.

Gas Heater Description

1. Heater body
2. Control panel
3. Central furnace end
4. Protective and ventilated panel
5. Support wheels
6. Gas valve
7. Gas container valve
8. Gas hose (maximum length: 50cm)
9. Gas pressure regulator
10. Gas cylinder clamp
11. Gas cylinder

Preparation

1. Carefully remove the heater from the package.
2. Make sure that the heating elements and other parts of the appliance have no remaining crumbles of packing foam plastic or other debris.
3. Carefully install the enclosed gas hose not twisting or breaking it. For that ,push on one end of the hose onto the gas valve connector (Nozzle), while the other end onto the connector of the enclosed gas pressure regulator. Secure gtghe hose ends on the connectors with jubilee clips.
4. Install a paronite/rubber spacer inside the cap nut checking its integrity beforehade and then carefully screw the nut on the outlet of an already prepared gas cylinder having appropriate capacity(a gas cylinder is not included in the delivery set and purchased separately). Twisting of the hose is strongly not allowed.
5. Slowly turning the gas pressure controller (cylinder check valve), make sure that no gas leakage are present. For that:
   • Lubricate all joints with soapy water. Gas leaks cause formation of bubbles in permeable places.
   • NEVER USE MATCHES OR LIGHTER FOR GAS LEAKAGE CHECKS.
   • If you find a gas leak, shut off the gas supply at the gas container valve and contact your dealer or manufactures’ service center.
6. Install the gas cylinder to the dedicated place inside the appliance and secure with the clamp.
7. Carry the heater to the supposed place of operation observing the rules and precautions described in this Instruction manual.
8. The appliance is ready for work.

SAFETY PRECAUTIONS

1. Always use the heater in accordance to the supplied instructions.
2. DO NOT place clothes or other material on the heater. This could cause a fire risk or affect the efficiency of the appliance.
3. DO NOT position the heater close to furniture.
4. DO NOT transfer the heater from one room to another, while it is on.
5. DO NOT position the heater close to walls, furniture, curtains, bed linen or any flammable materials as this could result in a higher risk of fire. The following minimum distances should always be respected: 50cm from the sides and 100cm from the front. Always face the heater towards the center of the room. The heater should be positioned on a level surface at all times.
6. If a leak is suspected:
   • DO NOT disconnect the regulator. Check all connections. Slowly turn the gas on and brush the connections with soapy water, or a leak detection spray. If there is a gas leak bubbles will form. In that case, please turn the gas off.
   • DO NOT use the heater again until a competent person in accordance with the Gas Safety (installations and use) Regulations 1998 has checked it.

Proper Use

Open the carton and take out the gas heater. Make sure the gas type you will use are exactly same as the one specified on the heater.
Operate the heater according to following procedures when gas power is used.

Operation Instructions

• This appliance is designed to be used with a 5 – 15 kg LPG gas cylinder. The maximum cylinder size should be: Diameter: 320mm, height: 650mm Take out of the rear panel and move a full gas cylinder into the heater. To prevent gas cylinder falling down at the counter side, fasten the rear panel reversely on the side panels.

• Joint the gas inlet of the heater with regular hose and hold tightly with clip. The other side of hose is connected to gas outlet of regulator and held tightly with clip. Turn the gas switch on, check gas tightness at the jointed parts by soapy water until gas leakage does not exist.

• Turn on the gas outlet regulator.
  The heater can be regulated to three different heat input stages: (PILOT), (LOW) and (HIGH). The ignition is operated by piezo electric push button.

  • Open the valve on the gas cylinder 1 ½ turns.
  • Press down and turn the control knob to PILOT start position and hold for 15-20 seconds.
  • While still pressing down the control knob, press the ignition button until the pilot flame ignited at the bottom of the burner. Continue to hold the control knob down for another 10- 15 seconds more, if the pilot flame goes out after releasing the button, please repeat the above operation.
  • After the pilot ignited, rotate the control knob to for HIGH rate for a while and then turn to LOW rate as wish.

1. PILOT start
2. Minimum heating capacity
3. Maximum heating capacity
4. Piezo electric ignition
5. Control knob

Combustion Control

• High: Press control knob lightly and rotate it to the position of double spark spot. HIGH heat settings will be activated.
• LOW: Press control knob lightly and rotate it to the position of single spark spot. LOW heat settings will be activated.

Shut off

• Rotate the control knob to PILOT position.
• Turn off the gas supply at the gas cylinder valve. Make sure the gas source is completely cut off.
• To be safety, it is necessary to operate the control knob at the back or side of heater. You can reignite heater after flame out for five minutes.

Attentions

• The heater shall be always used in ventilated room. Allow plenty of fresh air, never seal up the doorways and windows. This will bring efficient combustion and comfortable environment.

Safety protection system

The metal guard grill, covering at the top of ceramic tiles, will prevent people from touching very hot surfaces of the ceramic tiles. Do not remove the grill in any case. The grill is not enough to protect your children, never leave your child alone in the room. Do not touch safety devices and pilot burner under any circumstances.

Conduct regular gas leak check

• Shut off gas power as long as you smell gas and contact nearest agent for maintenance and repair.
• Do not attempt to check gas leak with a fire. As a temporary measure, you can smell or use soapy water to check the leakage location.

Specification

• With Oxygen Depletion Safety system and Anti-tilt Safety device
• Gas consumption: 3.8kW, 276g/h
• Gas hose: Certified gas hose according to applicable EN-standard (recommend 50mm) and comply with local code.
• Gas regulator: Certified according to EN16129:2013 and comply with local code (flow rate max. 1.5kg/h) The outlet pressure of the gas regulator should be suitable for use and comply with the pressure limits as listed in the below technical data.

Changing the cylinder

Gas container should be changed in accordance with this instruction manual.

• Change LPG cylinder in ample ventilated area, and from any ignition source (candle, cigarettes and so on).
• Take the heater outside and remove the rear panel. Lift out the cylinder and place it on the ground next to the heater. Unscrew the regulator hand wheel nut in a clockwise direction.
• Before connecting the refilled cylinder, check that the bull nose seal on the regulator is undamaged and in good condition. If in doubt take the regulator to a gas dealer to be checked.
• Connect the refilled cylinder and check for any gas leaks.
• If there are no leaks, fit the cylinder into the rear of the heater body making sure that the cylinder is placed in such a manner that hose is not trapped or kinked in any way.
• Fit the heater rear panel to the heater by engaging the clips.

Safety Tips

• This appliance requires installation by a competent person.
• This appliance requires a hose and regulator, check with your gas supplier.
• Don’t use in leisure vehicles such as caravans and auto caravans.
• The fire risks which would result to the positioning of the appliance close to walls, furniture, hangings, net curtains, bed linen and other inflammable materials. Minimum clearance to combustibles to the rear and sides of the heater is 100cm.
• Do not use the appliance unless the chrome wire safety guard is in place.
• The guard on this appliance is to prevent risk of fire or injury from burns and no part of it should be permanently removed. IT DOES NOT GIVE FULL PROTECTION FOR YONG CHILDREN OR THE INFIRM.
• To avoid twisting the flexible tubing or the hose.
• Do not move the appliance when lit or in use. Be aware that even after use the appliance remains hot for several minutes.
• Do not use the appliance if it is leaking gas (see notes on how to check for a gas leak).
• Keep the appliance away from flammable materials e.g. Clothes, curtains, upholstery, etc.
• Always change the gas cylinder outdoors and away from any sources of ignition.
• In the event of a burn back (where the flame burns back to the jet) immediately turn off the gas supply at the cylinder control valve. After ensuring that the flame is extinguished, re-light the appliance as described below. Should the appliance again burn back, close the valve and return the appliance to the supplier for examination.
• If there is an apparent gas leak on the appliance e.g. smell of gas, shut off the gas supply at the cylinder valve. Take the complete assembly outside into a flame free environment and test for the suspected leak as described below.
• Do not check for gas leaks with a naked flame as this is extremely dangerous!
• To check for a gas leak, use a brush dipped in a soapy water solution (e.g. water with dish washing liquid added) and apply the brush to the suspect areas such as the cylinder valve spindle or where the regulator screws into the cylinder. Also check the joins between the hose and regulator and between the hose and appliance. If there is a leak then bubbles will form. Should this happen, turn off the gas supply at the cylinder valve. Inspect the condition of the seal fitted on the regulator and ensure that it is in good condition. Refit the appliance to the cylinder and re-test using the soapy water solution. If the leak persists then return the appliance and the cylinder to the supplier for inspection and / or repair.
• This appliance shall not be used in high rise flats, in basements, bathrooms or bedrooms.
• Always turn off the appliance at the gas container valve and remove plug after use.
• Always leave the heater look upon the central room.
• Do not move the heater from front face. Do not move the burning heater from one room to another.
• Prevent people, especially young children and elderly people from touching very hot surfaces.
• Never dry clothes at the top of the metal guard grill.
• Keep all flammable materials at least one meter away from the heater.
• Never use or store solvents and pressure pack gas cylinders near a gas heater -even if the heater is turned off.
• Never dispose of rubbish such as cigarette butts in a gas fire -this can affect combustion and produce dangerous pollutants.
• Make sure rooms containing gas heater are well ventilated.
• Keep areas around the heater free of papers, trash, and any other combustible items.
• Place the heater on a level, hard, nonflammable surface; do not place on rugs, carpets or socket, near bedding or drapes, or on tables or countertops.
• Turn the heater at the gas cylinder valve off if you leave the area, and never leave a heater on while sleeping or if you leave home.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Maintenance

Do not use wet rag or sprinkling water on the heater while cleaning. This may cause serious problem to the heater. Under the circumstance of normal usage, contact our agents to conduct regular maintenance. Leave the heater at a clean and dry area when it is not used.

There is very little maintenance required on this appliance. Points to note are:

• Check that the regulator seal is undamaged when fitting a cylinder.
• Always check that the hose is in good condition before use and that it is securely clamped to the appliance and to the regulator.
• It is recommended that the hose be replaced every 2 years whether it has been used or not. When replacing the hose make sure that it is a proper hose for use with LPG. These are available from a gas dealer. When replacing the hose always replace the hose clamps at the same time.
• Hose that was found with leakage or blockage should be replaced immediately. Be aware that hose and regulator should be replaced when expired.
• With the exception of the hose and regulator there are no user fitted parts available for this heater. Should the heater not function properly, have it checked by a gas dealer and should replacement parts be required he / she will ensure that the correct parts be fitted in the proper manner.
• It is advisable to have the heater checked by a gas dealer before using every winter.
• Have your heater for serviced and checked every season or before use if it is stored for a long period.

TROUBLESHOOTING

2.    Deficient gas pressure of pipe gas

3.     Weak spark

| 1.   Turn on the gas power

2.     Use it when gas pressure becomes normal

3.     Check distance between ignition needle and the thermocouple (adjust it to around 4-5mm)

Flame failure if loosing hands| 1.  Thermocouple works improperly

2.     Ignition device gets loose

| 1.  Press control knob for 10 seconds, then ignite the heater

2.     Fasten ignition device

Salmon pink flame| Deficient maintenance| Contact local agent to conduct regular inspection and maintenance
Abnormal burning| 1.  Deficient pipeline natural gas pressure

2.    Gas passage blocked

| 1.  Use it when gas pressure becomes normal

2.     Cleaning gas passage

REPAIRS HAVE TO BE CONDUCTED BY AUTHORIZED PERSONNEL ONLY.

Model identifier(s): DA-303BF

Indirect heating functionality: [no]
Direct heat output: 3,8 (kW)
Indirect heat output: N/A (kW)
Fuel| | | Space heating emissions (*)
NOx
Select fuel type| | | 50 [mg/ kWhinput] (GCV)
| | |
Item| Symbol| Value| Unit| | Item| Symbol| Value| Unit
Heat output| | Useful efficiency (NCV)
Nominal heat output| Pnom| 3,8| kW| | Useful efficiency at nominal heat output| η th,nom| 100| %
Minimum heat output (indicative)| ****

Pmin

| ****

N/A

| ****

kW

| | Useful efficiency at minimum heat output (indicative)| ****

η th,min

| ****

N/A

| ****

%

| | | | | | | |
Auxiliary electricity consumption| | Type of heat output/room temperature control (select one)
At nominal heat output| el max| N/A| kW| | Single stage heat output, no room temperature control| [no]
At minimum heat output| el min| N/A| kW| | Two or more manual stages, no room temperature control| [yes]
In standby mode| el SB| N/A| kW| | With mechanic thermostat room temperature control| [no]
| | With electronic room temperature control| [no]
| | With electronic room temperature control plus day timer| [no]
| | With electronic room temperature control plus a timer| [no]
| | Other control options (multiple selections possible)
| | Room temperature control, with presence detection| [no]
| | Room temperature control, with open window detection| [no]
| | With distance control option| [no]
| | With adaptive start control| [no]
| | With working time limitation| [no]
| | With black bulb sensor| [no]
Permanent pilot flame power requirement| |
Pilot flame power requirement (if applicable)| P pilot| 0.18| kW| | | | |

Contact details

| IMPORTED IN ΕU BY EUROLAMP SA: KAMPOS DIAVATA – IONIA / 570 08 / THESSALONIKI – GREECE / T: +30 2310 574802

MADE IN CHINA info@eurolamp.gr / www.eurolampglobal.com

(*) NOx = nitrogen oxides

www.eurolampglobal.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>