MEEC TOOLS Pyrography Kit 30 W 400-500 °C Instruction Manual

MEEC TOOLS Pyrography Kit 30 W 400-500 °C

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)

Important!
www.jula.fr

INSTALLATION

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Risk of eye damage. Wear safety glasses when working with melted solder.
• Risk of damage to lungs and respiratory tracts. Avoid inhalation of fumes and smoke from soldering. Only solder in a well-ventilated area.
• Risk of serious burn injury. The soldering tip gets very hot when in use – do not touch the soldering tip.
• Unplug the power cord after use.
• Do not leave the product unattended or on a flammable surface before it has cooled.
• Store out of the reach of children.
• Always be careful when using the product in places where there is a flammable material.
• Always check before use that the product, its power cord and plug, are undamaged and safe to use.
• Check that the mains voltage corresponds with the rated voltage on the type plate.

SYMBOLS

| Read the instructions.
---|---

| Approved in accordance with the relevant directives.
****| Recycle discarded product in accordance with local regulations.

TECHNICAL DATA

• Rated voltage 230 V ~ 50 Hz
• Output 30 W
• Temperature range 400-500°C
• Cord length 1.3 m

DESCRIPTION

Pyrography kit including soldering pen, hot knife, three pattern tips, seven cutting tips and stand. The kit is packed in the supplied storage box. The 30 W soldering pen has enough power for soldering normal electronics and reduces the risk of overheating the soldered components.

USE

PREPARATIONS

1. Lay out all the necessary material and make sure the area where the soldering is to be carried out is well-ventilated.

2. Plug the soldering pen into a power point.

3. Allow the soldering tip to warm up (about 2 minutes).
   TINNING THE TIP

4. Touch the solder with the soldering tip and allow a drop of melted solder to flow over the tip. This removes any oxide from the soldering tip. If the solder does not melt, wait a little for the soldering tip to warm up. If the solder still does not melt, see below.

5. Wipe the soldering tip against a damp sponge to remove the solder.

SOLDERING

1. Heat the junction by touching it with the soldering tip.
2. Put solder in the contact point between the soldering tip and the junction.
3. Lift off the soldering tip and the soldering wire from the junction at the same time.
4. Check that the surface of the solder is bright and smoothed out. See troubleshooting instructions if the surface of the solder is dull.

REMOVING SOLDER BRIDGING
A solder bridge occurs if the solder from two adjacent junctions melts together. This often happens when too much solder is applied. Because solder bridges cause short circuiting on circuit boards, they must be removed by drawing the soldering tip straight through the bridge.

MAINTENANCE

Maintenance of the soldering pen preserves its correct functionality and increases its life span.

DURING USE

• Pull out the plug when the soldering pen is not in use to counteract oxidisation of the soldering tip.

DURING STORAGE

• Tin the soldering tip as described in the section Tinning the tip.
• Do not pull the power cord to pull out the plug.

TROUBLESHOOTING

THE SOLDER DOES NOT MELT

1. Wait another five minutes to allow the soldering tip to warm
   up. If the solder still does not melt, go to step 2.

2. Touch the soldering tip with a wet sponge.

   • Result 1: The soldering tip is correctly heated if steam develops and there is a hissing sound. Continue to step 3.
   • Result 2: If no steam is formed and there is no sound, connect the soldering pen to another power point. Repeat step 1.

THE SOLDERING HAS A DULL SURFACE OR SEEMS BRITTLE

1. Clean the soldering tip with the damp sponge.
2. Tin the soldering tip as described in the section Tinning the tip.
3. Hold the soldering tip firmly pressed against the junction for a few seconds.
4. Put solder in the contact point between the soldering tip and the junction.
5. Lift the soldering tip of the junction.

JULA AB, BOX 363, SE-532 24 SKARA
2021-11-22
© Jula AB

References

• Jula – products for home and garden
• Jula - Mikään ei voi pysäyttää sinua nyt!
• Jula - ingenting kan stoppe deg nå!
• Jula - Teraz nic Cię nie powstrzyma!
• Jula – inget kan stoppa dig nu!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>