MEEC TOOLS 230V 900W Belt Sander Instruction Manual

: June 3, 2024
: MEEC TOOLS

MEEC TOOLS 230V 900W Belt Sander

SAFETY INSTRUCTIONS

WARNING!
Read all the safety instructions and other instructions. Failure to follow all the instructions and safety instructions can result in the risk of electric shock, fire and/ or serious personal injury. Save all warnings and instructions for future reference.
The term “power tool” in all the warnings below refers to mains-powered (corded) or battery-powered (cordless) power tools.

WORK AREA

Keep the work area clean and well lit.
Dark and cluttered work areas increase the risk of accidents and injuries.
Do not use power tools in explosive environments, such as in the vicinity of flammable liquids, gas or dust. Power tools produce sparks that can ignite dust and fumes.
Keep onlookers, especially children, at a safe distance when using power tools.
You can easily lose control of the power tool if you are distracted.
The work area should be well ventilated.

ELECTRICAL SAFETY

The plug on the power tool must match the power point. Never modify the plug in any way. Never use an adapter with earthed power tools. Unmodified plugs and matching power points reduce the risk of electric shock.
Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the mains socket. Keep the power cord away from heat, oil, sharp edges and moving parts.
Damaged or tangled power cords increase the risk of electric shock.
If using the tool outdoors, only use an extension cord approved for outdoor use. Cords intended for outdoor use reduce the risk of electric shock.
If it is absolutely necessary to use power tools in damp conditions, use a mains connection protected by a residual current device (RDC). A residual current device reduces the risk of electric shock.
Do not use the tool if the power cord is damaged. Pull out the plug immediately if the cord is damaged when working.
Do not pull the power cord to unplug the plug. Damaged power cords increase the risk of electric shock.

PERSONAL SAFETY

Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. A moment of inattention or carelessness can result in serious personal injury.
Use personal safety equipment. Wear safety glasses or a visor. Depending on the type of tool and how it is used, safety equipment such as dust masks, non-slip safety shoes, safety helmets and ear protection reduce the risk of personal injury.
Avoid accidental starting. Check that the power switch is in the OFF position before plugging in the plug or battery, or lifting/ carrying the tool. Carrying a power tool with your finger on the switch or connecting a tool to the mains supply when the switch is in the ON position increases the risk of accidents and injuries.
Remove adjuster keys/spanners before switching on the power tool. Spanners or the like that are left in a rotating part of the power tool can cause personal injury
Do not overreach. Always maintain a firm footing and good balance. This ensures better control over the power tool in unexpected situations.
Wear suitable clothing. Do not wear loose-fitting clothing or jeweler. Keep your hair, clothing and gloves away from moving parts. Loose-fitting clothing, jeweler and long hair can get caught in moving parts.
If dust extraction and dust collection equipment is available, this should be connected and used correctly. The use of such devices can reduce the risk of dust-related problems. Clean the ventilation openings regularly. The accumulation of metal dust can cause the metal parts of the tool to become live – risk of electric shock.
Do not allow familiarity with similar tools to lead to exaggerated self-confidence and to neglect the safety instructions for the tool. A moment of inattention or carelessness can result in serious personal injury

USE AND CARE

Do not force the power tool. Use the correct power tool for the planned work.
The tool does the job better and more safely when used at the rate for which it was designed.
Do not use the power tool if it cannot be switched on and off with the powerswitch. Power tools that cannot be controlled with the power switch are dangerous and must be repaired.
Pull out the plug and/or remove the battery before making any adjustments, changing accessories or putting the power tool away. These safety precautions reduce the risk of accidentally starting the power tool.
Store power tools out of the reach of children when not in use. Never allow children, or anyone who is unfamiliar with the power tool and these instructions, to use the tool. Power tools are dangerous if used by inexperienced persons.
Maintain power tools and accessories.
Check that moving parts are properly adjusted and do not jam, and that no parts are incorrectly fitted or damaged.
Check for other factors that could affect functionality. If a power tool is damaged it must be repaired before it is used again. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
Use the power tool, accessories and bits etc., in accordance with these instructions, taking into account the actual working conditions and the work that is to be done. It can be dangerous to use power tools for purposes other than those for which they are intended to be used.
Keep handles and grips clean, dry and free from oil and grease. Greasy handles and grips make it difficult to hold and control the tool in unexpected situations.

SERVICE

Power tools must only be serviced by qualified personnel using identical spare parts. This will ensure that the power tool remains safe to use.

SPECIAL SAFETY INSTRUCTIONS

Only use accessories recommended by the manufacturer. The use of other accessories can result in a risk of personal injury.
Only use the tool for dry sanding. There is an increased risk of electric shock if water enters a power tool.
Find out whether sanding the surface in question can product toxic dust and/or fumes. Dust/fumes from wood, metal and paint etc. can cause allergic reactions and/or can be harmful to health Observe special care and avoid inhaling and skin contact with such materials.
Materials that contain asbestos should only be handled by qualified personnel.
Do not put your hands under the workpiece – risk of personal injury.
Make sure there are no nails, screws or other foreign objects in the workpieces.
Dust from wood, metal and lead-based paint can be harmful to health.
– All persons in the work area must wear a filter mask that provides protection from dust.
– Use a dust extractor and keep the work area well ventilated.
– Children and pregnant women must not go into the work area.
– Avoid eating, drinking or smoking in the work area.
Older types of paint on metal or wood can be lead-based. Contact a professional if you suspect that the paint is lead-based.
Dust from some types of wood and wood products, e.g. chipboards and fiberboards can be harmful to health. Wear a dust filter mask with replaceable filter and use a dust extractor.
Stand firmly and make sure that the power cord does not touch the tool, or fasten and get in the way.
The tool removes material by means of abrasion.
Check that there are no nails or other foreign objects in the workpiece.
Do not use the tool for wet sanding.
Secure small workpieces so that they cannot move.
Do not overload the tool. Let the tool do the work. Do not overload the tool and reduce the motor speed. Pressing harder will not speed up the work, but will put more strain on the tool and accessories.
Do not use the dust bag when sanding metal. Hot metal particles could ignite the filter or residual wood dust.
Do not use worn, damaged or clogged sanding belts.
Do not touch the sanding belt when the tool is running.

SAFETY INSTRUCTIONS FOR BELT SANDERS

Hold the power tool by the insulated grips when working in areas where the tool may come into contact with concealed electrical cables or its own power cord. Contact with a live cable will cause the metal parts on the tool to also become live – risk of electric shock.
Before starting work on walls, ceilings or floors, check that there are no concealed electrical cables or conduits. Use a live wire detector, or ask an electrician for help. Failure to observe these instructions could result in the risk of fire, explosion, electric shock, personal injury and/or material damage.
Avoid accidental starting. Switch off the tool if the power supply is disconnected, e.g. as a result of a power cut or if the power cord is pulled out.
Secure the workpiece. Secure the workpiece with clamps or a vice. Never hold the workpiece with your hand.
Keep the work area clean. The mixing of dust from different materials is especially dangerous. Dust from light metals, e.g. aluminium, can ignite or explode.
Avoid overheating the tool and workpiece – risk of material damage.
Do not touch accessories during or immediately after use – risk of burn injury.
Never clean hot tools with flammable agents – risk of fire and/or explosion.
In addition to these instructions, you should always comply with local regulations and laws concerning health, safety and the environment.
Do not remove or cover symbols and markings on the product. Replace any stickers that have become illegible or lost.

MINIMISATION OF NOISE AND VIBRATION

To reduce noise and vibrations when in use, limit the time the tool is in use, and use low power/vibration mode and suitable safety equipment. Take the following precautions to minimise the risks of exposure to vibrations and/or noise.

Only use the product as it is intended to be used and in accordance with these instructions.
Make sure that the product is in good condition.
Use accessories in good condition, and which are suitable for the purpose.
Keep a firm grip on the handles/grips.
Maintain the product in accordance with these instructions and keep it well lubricated (where appropriate).
Plan the work so that exposure to heavy vibrations is spread over a longer period.

SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.
| Wear ear protection
| Wear safety glasses.
| Use a face mask.
| Safety class II

TECHNICAL DATA

Rated voltage 230 V ~ 50 Hz
Output 900 W
Belt speed 120 – 380 m/min
Sandpaper size 76 x 533 mm
Cord length 2 m
Weight 3 kg
Sound power level, LwA 101 dB(A), K= 3 dB
Sound pressure level, LpA 90dB(A), K= 3 dB
Vibration level 6.402 m/s2 , K= 1.5 m/s2

Always wear ear protection!
The declared values for vibration and noise, which have been measured according to a standardised test method, can be used to compare different tools with each other and for a preliminary assessment of exposure. The measurement values have been determined in accordance with EN 62841-2-4:2014.

WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

DESCRIPTION

Belt sander with retractable hood in front for access to confined spaces. With adjustable belt speed, fixed support handle, removable sanding frame and connection for dust collector. One sandpaper, dust collector and two clamps included.
FIG. 1

USE

WARNING!
Switch off the tool and pull out the plug before adjusting, replacing accessories, cleaning or maintenance.

CHOOSING SANDING BELTS

Extra sanding belts and belts with different grades (coarse, medium and fine) can be bought from Jula’s department stores and at www.jula.com. Use coarse sanding belts for rough work, medium belts to smooth the workpiece, and fine sanding belts to finish off. Try them out on a spare piece to see which grade is suitable for the job.

FITTING AND REPLACING SANDING BELT

Select a suitable grade of sanding belt.
Pull up the lever that tensions the sanding belt.
FIG. 2
Put on a sanding belt with the arrow on the inside of the belt pointing the same way as the direction of rotation on the tool.
Fold down the lever.
FIG. 3

NOTE :

Do not use worn, damaged or clogged sanding belts.
Do not use the same sanding belt for metal and wood. Metal particles embedded in the sanding belt will damage the surface of the wood.

ADJUSTING THE SANDING BELT

Tension the sanding belt. Plug in the power cord and start the tool briefly. The belt rotates for a short while.
FIG. 4

FIG. 5
While the belt is moving, turn the adjusting knob so that the belt runs in the middle of the roller.
FIG. 6
Press the power switch and turn the adjusting knob until the belt is properly adjusted.
Run the tool for one minute to check that the adjustment is correct before sanding.

DUST COLLECTION

Always use a dust extractor if possible. Push the dust bag onto the dust extraction port.
FIG. 7

STARTING/STOPPING
Push the power switch to start the tool and release the power switch to switch off.

Continuous operation

Activate
Press the lock button when the power switch is pressed.
FIG. 8

Deactivate
To switch off the tool, press the power switch and then release it.
FIG. 9

NOTE :

Always lift the tool off the workpiece before starting/stopping the tool.
It can pull away on first contact with the workpiece.

SANDING

NOTE :

Do not use the tool on plaster.

Secure small workpieces so that they cannot move.
Place the tool on the workpiece without pressing and start the tool.
Move the tool slowly over the workpiece. For best results, move the tool backwards and forwards, not in circles – this can cause the sanding belt to shift. Sand in the direction of the grain, with parallel, overlapping strokes.
• When removing paint and sanding very rough wood, sand at a 45° angle to the direction of the grain in two directions, and then in the direction of the grain.
• Only use the front roller to sand corners and irregular workpieces.
• Always lift the tool off the workpiece before stopping it. The sanding belt continues to move for a few seconds after the motor is switched off – keep your hands away.
FIG. 10

Tips!
If there are any scratches or marks on the workpiece after sanding, do as follows:
– Sand with a coarser grade of sanding belt.
– Use a new sanding belt of the same grade.