TRUE FINE TD10023FL Sputnik 23 in. 6-Light Brass Semi Flush Mount Ceiling Light Instruction Manual

: October 30, 2023
: TRUE FINE

Table of Contents

TD10023FL Sputnik 23 in. 6-Light Brass Semi Flush Mount Ceiling Light
Overview
Product Information
Product Usage Instructions
Wiring Instructions
Assembly Instruction
Product Specifications
Product Packaging
Cleaning
Safety Information
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TD10023FL Sputnik 23 in. 6-Light Brass Semi Flush Mount Ceiling Light

Overview

Product Information

The Flush Mount Lighting is a product designed for indoor lighting purposes. It comes with a fixture body (A), stem (B), canopy (D), mounting strap (E), finial (C), wire nuts, and screws for installation. The product is designed to be connected to an outlet box with black and white wires and a ground wire using wire connectors. The fixture body is made of glass and metal, and it requires a maximum of 60 watts incandescent bulbs.

Product Usage Instructions

Pass the wires through Stem (B) and Canopy (D) and tighten them.
Fix Mounting strap (E) to outlet box with Screw (F).
Connect the wires according to the wiring instruction provided in the manual.
Pass Canopy (D) through the screw and fix it with Finial (C).
Install a light bulb with a maximum of 60 watts incandescent bulbs.
To clean the fixture, wipe it with a soft cloth and clean the glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Always switch off the electricity supply and allow the fixture to cool for 10 minutes before changing the light bulb.

Wiring Instructions

Insert the green grounding screw into the hole with two raised dimples on the mounting bar.
Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
- [GROUP A]: Connect to Black House Wire
- [GROUP B]: Connect to White House Wire
Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
[GROUP A]:

Connect to Black House Wire

| [GROUP B]:

Connect to White House Wire

---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
10. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors. 11. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. 12. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection. 13. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Assembly Instruction

Pass the wires through Stem (B) and Canopy (D) and tighten them.
Fix Mounting strap (E) to outlet box with Screw (F).
Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
Pass Canopy (D) through the screw and fix it with Finial (C).

Product Specifications

Input voltage 120V
Rated power 60W MAX × 6
Lamp socket E26

Product Packaging

Fixture body × 1
Stem × 1
Mounting strap × 1 & Canopy × 1
Screw × 2 & Wire nut × 3
Lamp instruction × 1

Cleaning

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.