TRUE FINE TD20029FL Celina 3 Light Drum SemiFlush Mount Light Instruction Manual

TRUE FINE TD20029FL Celina 3 Light Drum SemiFlush Mount Light

Product Information

The 3-Light Flush Mount Lighting (TD20029FL) is a ceiling light fixture that comes with metal bands, a canopy, a mounting strap, screws, wire nuts, a shade, an acrylic board, and lamp instructions. The fixture requires three E26 bulbs that are not included. The input voltage for the fixture is 120V, and the maximum rated power is 60W.

Product Usage Instructions

1. Assemble the metal band (B) by screw nut (C) onto the canopy (A) and bottom frame (E).
2. Assemble two pieces of metal band (B) first, then put the shade (D) on. After that, repeat step 1 to assemble the third and last metal band.
3. Adjust the three metal bands (B) and make sure they’re all well positioned, then tighten all screw nuts (C).
4. Install bulbs (not included), need three E26 bulbs.
5. Fix mounting strap (I) to outlet box with screw (G).
6. Connect the wires according to the wiring instruction provided. Do not connect the ground wire to black or white power supply wires.
7. Place canopy (A) onto the outlet box, and secure with screw (H).
8. Peel off the protective cover on the acrylic board (G).
9. Gently bend the acrylic board (G) a little bit and insert it into the bottom of the fixture and then release it. Adjust it to make it well-positioned.

Product Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
2. Identify which group your fixture wire(s) falls into and connect the wires according to the directions provided.
3. Take your fixture wire(s) from [Group A] and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Cleaning

To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powder, steel wool, or abrasive paper.

Product Safety Information

Make sure to follow the wiring instructions provided carefully to avoid any electrical hazards. Do not connect the ground wire to black or white power supply wires. Do not use abrasive materials to clean the fixture.

Instructions Manual

3-Light Flush Mount Lighting

• TD20029FL

Overview

Assembly Instruction

1. Assemble Metal band(B) by Screw nut(C ) onto Canopy(A) and Bottom frame( E )
2. Assemble 2 pcs of Metal band(B) first, then put the shade on. After that, repeat step 1 to assemble the third and last metal band.
3. Adjust the 3 Metal bands(B) and make sure they’re all well positioned, then tighten all Screw nuts( C )
4. Install Bulbs (not included), need three E26 bulbs.
5. Fix the Mounting strap (I) to the outlet box with Screw (G).
6. Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
7. Place Canopy (A) onto the outlet box, and secure it with Screw (H).
8. Peel off the protective cover on the acrylic board(G)
9. Gently bend the acrylic board (G) a little bit and insert it into the bottom of the fixture and then release it. Adjust it to make it well-positioned.

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
   [GROUP A]:

Connect to Black House Wire

| [GROUP B]:

Connect to White House Wire

---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WHITE TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD, OR BLACK

WITHOUT TRACER

| BROWN, GOLD, OR BLACK

WITH TRACER

3. Take your fixture wire(s) from [Group A] and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do the steps3 and4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

• Input Voltage: 120V
• Rated Power: 60W Max
• Lamp Socket: E26

Product Packaging

• Metal band x 3 & Screw nut x 6
• Canopy x 1 & Mounting strap x 1
• Screw x 2 & wire nut x 3
• Shade x 1
• Acrylic board x 1
• Lamp instruction x 1

Cleaning

• To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Safety Information

• Always switch off the electricity supply and allow it to cool for 10 minutes before changing the light bulbs.

CONTACT US

E-mail: service@24h-reply.com.

References

• Digital Services, Technology and Consulting | Reply

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>