TRUE FINE TD10026C 4-Light Chandelier Instruction Manual

TRUE FINE TD10026C 4-Light Chandelier

Product Information

The 4-Light Chandelier is a ceiling-mounted lighting fixture that comes with a fixture body, mounting strap, canopy, canopy lock ring, fixture chain, and wire connectors. The product is designed to be connected to an outlet box and is suitable for indoor use. The chandelier does not come with light bulbs, and the user needs to purchase them separately.

The fixture has two groups of wires: Group A comprises green, bare copper wire, and white ribbed wire. Group B comprises the fixture chain, mounting strap, canopy, canopy lock ring, and fixture body. The wiring instructions provide a clear picture of  how to connect the wires to the outlet box.

Product Usage Instructions

1. Pass the wire through Loop (C), then screw Loop (H) to Fixture body (A).
2. Fix Mounting strap (G) to outlet box with Screw (F).
3. Link Loop (B) and Canopy (E) by Fixture chain (C).
4. Connect the wires according to the wiring instructions.
5. Fix Canopy (E) to Mounting strap (G) with Canopy lock ring (D).
6. Install light bulbs (not included).

Wiring Instructions

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
   • [GROUP A]: Connect to Black House Wire
   • [GROUP B]: Connect to White House Wire
3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Cleaning:
To clean the fixture, wipe it with a soft cloth. Clean the glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Safety Information:
Always switch off the electricity supply and allow it to cool for 10 minutes before changing the light bulbs.

Contact Information:
If you have any questions or concerns regarding the product, you can contact us via email at service@24h-reply.com.

Overview

Assembly Instruction

1. Pass the wire through Loop (C), then screw Loop (H) to Fixture body (A).
2. Fix Mounting strap (G) to outlet box with Screw (F).
3. Link Loop (B) and Canopy (E) by Fixture chain (C).
4. Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
5. Fix Canopy (E) to Mounting strap (G) with Canopy lock ring (D).
6. Install the bulbs(not included).

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. [GROUP A]:
   Connect to Black House Wire| [GROUP B]:
   Connect to White House Wire
   ---|---
   BLACK| WHITE
   PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
   WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
   BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

• Input voltage 120V
• Rated power 60W MAX × 4
• Lamp socket E12
• Cord Length 7ft.

Product Packaging

• Fixture body × 1
• Loop × 1 & Fixture chain × 1
• Mounting strap × 1
• Canopy × 1 & Canopy lock ring × 1
• Screw × 2 & Wire nut × 3
• Lamp instruction × 1

Cleaning

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Safety Information

Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US
E-mail: service@24h-reply.com

References

• Digital Services, Technology and Consulting | Reply

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>