TRUE FINE TD90031FL Bohemian Rattan Semi Flush Mount Ceiling Light Instruction Manual

TRUE FINE TD90031FL Bohemian Rattan Semi Flush Mount Ceiling Light

Product Information

The Flush Mount Lighting product is a lighting fixture that is designed to be mounted onto an outlet box. The product has a fixture body (A), shade (B), socket ring (C), mounting strap (E), and canopy (D). The wiring of the product follows a group system where [GROUP A] consists of wires that need to be connected to the black house wire and [GROUP B] consists of wires that need to be connected to the white house wire. The product has an input voltage of 120V and a rated power of 40W MAX. The product uses an E26 lamp socket.

Product Usage Instructions

1. Attach the shade (B) onto the socket and tighten it with the socket ring (C).
2. Fix the mounting strap (E) to the outlet box using the long screw (F).
3. Connect the wires according to the picture above, making sure to follow the wiring instructions for details.
   • Insert the green grounding screw into the hole with two raised dimples on the mounting bar.
   • Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied).
   • If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   • Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions provided.
   • Connect the fixture wire from [Group A] to the black wire from the outlet box.
   • Connect the fixture wire from [Group B] to the white wire from the outlet box.
   • Make sure no bare wires can be seen outside wire connectors.
   • Never connect ground wire to black or white power supply wires.
4. Place the canopy (D) onto the outlet box and secure it with the short screw (G).

Overview

Assembly Instruction

1. Attach Shade (B) up onto the socket , then tighten with Socket ring (C).
2. Fix Mounting strap (E) to outlet box with Long screw (F).
3. Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
4. Place Canopy (D) onto the outlet box, secure with Short screw (G).

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
   [GROUP A]: Connect to Black House Wire| [GROUP B]: Connect to White House Wire
   ---|---
   BLACK| WHITE
   PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
   WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
   BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER

3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.

4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.

5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.

6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

• Input voltage 120V
• Rated power 40W MAX
• Lamp socket E26

Product Packaging

• Fixture body × 1
• Mounting strap × 1
• Screw × 2 & Wire nut × 3
• Shade × 1
• Lamp instruction × 1

Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US
E-mail:service@24h-reply.com

References

• Digital Services, Technology and Consulting | Reply

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>