MEEC TOOLS 019114 Soldering Gun Kit User Manual

019114 Soldering Gun Kit
User Manual
Item no. 019114

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Never place a soldering pen directly on a workbench or other surface, regardless of whether it is hot or cold – always put it in a stand during pauses in the work or before putting it away.
• A damaged cord or plug must be replaced by an authorised service centre or other qualified personnel to ensure safe use.
• Check that the mains voltage corresponds with the rated voltage on the type plate.
• Keep children under supervision to make sure they do not play with the product.
• Smoke will develop from the soldering tip the first time the product is connected to a power point. This is completely normal and soon stops.
• Use a soldering stand and a suitable helping hand device to minimise the risk of burn injuries.
• Never use the product if the soldering tip is not correctly and firmly pressed in place – otherwise this will reduce the life span of the heating element.
• Pull out the plug and allow the product to cool after use before putting it away.
• Do not file soldering tips of the long-life type.
• Be careful when using the product in places where there is flammable material.
• Do not apply to the same point for too long.
• Do not use in explosive environments.
• Be aware that heat can be conducted to flammable material that is out of sight.
• Do not leave the product unattended or on a flammable surface before it has cooled.
• Risk of eye damage. Wear safety glasses when working with melted solder.
• Risk of damage to lungs and respiratory tracts. Avoid inhalation of fumes and smoke from soldering. Only solder in a well ventilated area.
• Risk of serious burn injury. The soldering tip gets very hot when in use – do not touch the soldering tip.

SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Safety class II
| Recycle discarded product in accordance with local regulations.

TECHNICAL DATA

DESCRIPTION

Soldering gun (100 W) and soldering iron (30 W). The kit also includes a repair stand with crocodile clips, table stand for the soldering iron, soldering paste, tin solder and a  solder sucker. Extra tip included.

1. Soldering gun 100 W
2. Soldering pen 30 W
3. Tin solder
4. Stand for soldering pen
5. Extra tip for soldering gun
6. Scraper
7. Solder sucker
8. Soldering paste
9. Fixed magnifying glass
   FIG. 1

USE

SOLDERING GUN 100 W

1. Check that the mains voltage corresponds to the rated voltage on the type plate.
2. Plug in the power cord and press the power switch. After 20 seconds the tip has reached 300°C and the product is ready to use.
3. Never lock the power switch in the On position – risk of overheating and serious material damage.
4. First warm the parts that are to be soldered, and then put the solder on the junction.

Replacing the soldering tip

1. Undo the two retaining screws.
2. Remove the old tip and put in a new one.
3. Press in the tip as far as it goes and tighten the screws.
4. The transfer of heat will be reduced if the screws are not correctly tightened.
   FIG. 2

SOLDERING PEN 30 W

1. Check that the soldering tip is correctly in place and the retaining screws tightened.
2. Plug in the power cord.
3. Do not allow the soldering pen to heat up without a soldering tip.
4. Check that the product has enough power to heat the parts to be joined.
5. Clean the parts that are to be joined. Do not touch the clean parts, grease reduces the capacity of the solder to adhere.
6. Heat up the parts and apply solder. If the parts are properly cleaned and heated the solder spreads smoothly.

Replacing the soldering tip

1. Switch off the product, unplug the power cord and allow the product to cool before replacing the soldering tip. Undo the retaining screws and carefully pull out the tip.  Press in a new tip as far as it goes and tighten the screws.
   FIG. 3

Jula reserves the right to make changes.
For latest version of operating instructions, see www.jula.com
2021-11-24
© Jula AB
Jula AB, Box 363, SE-532 24 SKARA

Documents / Resources

| MEEC TOOLS 019114 Soldering Gun Kit [pdf] User Manual
019114 Soldering Gun Kit, 019114, Soldering Gun Kit, Gun Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>