MEEC TOOLS 018231 00 W 400-500 °C Soldering Gun User Manual
- June 8, 2024
- MEEC TOOLS
Table of Contents
Item no. 018231
100 W 400-500 °C
User Manual
OPERATING INSTRUCTIONS
Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)
SAFETY INSTRUCTIONS
- This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
- Always check before use that the product, its power cord and plug, are undamaged and safe to use.
- Check that the mains voltage corresponds with the rated voltage on the type plate.
- Avoid using the product in damp conditions or rain – risk of electric shock.
- Do not allow water or any other liquid to get into the product.
- Do not dismantle the product – risk of electric shock.
- A damaged cord or plug must be replaced by an authorised service centre or other qualified personnel to ensure safe use.
- The product is only intended to be used for household use.
- The product is not intended for hard soldering.
- Unplug the power cord after use.
- Do not leave the product unattended or on a flammable surface before it has cooled.
- Keep out of the reach of children
- Always be careful when using the product in places where there is flammable material.
- Do not apply to the same point for too long.
- Do not use in explosive environments.
- Be aware that heat can be conducted to flammable material that is out of sight.
- Put the product on its stand after use, and allow it too cool before putting it away.
- Risk of eye damage. Wear safety glasses when working with melted solder.
- Risk of damage to lungs and respiratory tracts. Avoid inhalation of fumes and smoke from soldering. Only solder in a well ventilated area.
- Risk of serious burn injury. The soldering tip gets very hot when in use – do not touch the soldering tip.
SYMBOLS
| Read the instructions
---|---
****| Approved in accordance with the relevant directives.
| Safety class II
| Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
| Rated voltage | 230 V ~ 50 Hz |
|---|---|
| Output | 100 W |
| Temperature range | 400-500°C |
| Cord length | 1.1 m |
DESCRIPTION
High speed soldering gun with resistive heating element supplied from
transformer. Short heating time and low power consumption.
The pistol grip and soldering tip light make the product easy and convenient
to use. Quick and effective heat transfer for soft soldering. Extra tip
included.
- Soldering tip
- Sleeve
- Status and torch light
- Trigger
- Handle
- Plug
FIG. 1
USE
The product is intended to be supplied with 230 V ~ 50 Hz. Check that the mains voltage corresponds to the rated voltage on the type plate. Plug the plug into a suitable power point. Hold the product by the handle. Point the soldering tip at the junction and press the trigger. The status and torch light go on. After six–eight seconds the soldering tip is heated to 230°C and the soldering can be carried out. The solder temperature is controlled with the trigger. The soldering tip is supplied with power when the trigger is pressed and its temperature increases. For this reason do not press the trigger all the time, release it now and then so that the temperature drops a little. Release the trigger when the soldering tip begins to get too hot, but after no more than 12 seconds, and keep it released for at least 48 seconds for it to cool. Press the trigger again when temperature of the soldering tip begins to get too low – the temperature will then quickly increase. The soldering temperature is kept within suitable limits in this way, which ensures better results, reduces oxidisation on the soldering tip and increases the life span.
MAINTENANCE
REPLACING THE SOLDERING TIP
The soldering tip can after prolonged use become oxidised and worn thin,
and should therefore be replaced.
Undo both retaining screws on the soldering tip. Remove the old soldering tip,
fit a new one and tighten the screws. The product can now be used again as
usual.
REPLACING BULB
Contact the retailer if the bulb needs to be replaced. Bulb data: 6 V, 3 W.
Jula reserves the right to make changes.
For latest version of operating instructions, see
www.jula.com
2021-11-24
© Jula AB
Jula AB, Box 363, SE-532 24 SKARA
Documents / Resources
| MEEC
TOOLS 018231 00 W 400-500 °C Soldering
Gun
[pdf] User Manual
018231 00 W 400-500 C Soldering Gun, 018231, 00 W 400-500 C Soldering Gun,
Soldering Gun, Gun
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>