vita SP-A1688-UV Bottom Loading Water User Manual

vita SP-A1688-UV Bottom Loading Water

SAFETYINSTRUCTION

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play children without with the appliance.
   Cleaning and user maintenance shall not be made by supervision.

2. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.

3. This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by lay persons.

4. If the supply wrd is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

5. The appliance must not be cleaned by a water jet.

6. The appliance is suitable for indoor use only.

7. WARNING : Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

8. WARNING : Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

9. WARNING : Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

PART NAME

NOTE
This machine can be suitable for bottle of 5 gallons. Do not use unhealthy hard water.

AFETY PRECAUTIONS

WARNING

• To reduce risk of injury and property damage, user must read this entire guide before assembling, installin g & operating dispenser.
• Failure to execute the instructions in this manual can cause personal injury or property damage.
• This product dispenses water at very hi gh temperatures. Failure to use properly can cause personal injury.
• When operating this dispenser, always exercise basic safety precautions, including the following:
• Prior to use, this dispenser must be properly assembled and installed in accordance with this manual.
• This dispenser is intended for water dispensing only. DO NOT use other liquids DO NOT use for other purposes. Never use any other liquid in the dispenser other than known and microbiologically safe bottled water.
• For indoor use only. Keep water dispenser in a dry place away from direct sunlight. DO NOT use outdoors.
• Install and use only on a hard, flat and level surface.
• DO NOT place dispenser into an enclosed space or cabinet.
• DO NOT operate dispenser in the presence of explosive fumes.
• Position back of dispenser no closer than 20cm from wall and permit free airflow between wall and dispenser. There must be at least 20cm clearance on the sides of the dispenser to permit airflow.
• Use only properly grounded outlets.
• Do not use an extension cord with your water dispenser.
• Always grasp plug and pull straight out from outlet. Never unplug by pulling on power cord.
• DO NOT use dispenser if cord becomes frayed or otherwise damaged.
• To protect against electric shock. DO NOT immerse cord, plug, or any other part of dispenser in water or other liquids.
• Ensure dispenser is unplugged prior to cleaning.
• Never allow children to dispense hot water without proper and direct supervision. Unplug unit to prevent unsupervised use by chalder.
• Service should be performed only by a certified technician.
•   Warning : DO NOT damage the refrigerant circuit.
• The appliance is not intended for use by persons (including children) with reduce physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safely.
• This appliance is intended to be used in household and similar applications such as: -staff kitchen in hotels, motels and other residential type
• farm houses; -by clients in hotels, motels and other residential type environments; -bed and breakfast type environments’.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified avoid.
• The appliance must MT be cleaned by a waters.
• The appliance is suitable for indoor only.
• WARNING : Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• WARNING : Do not  mechanical devices or other to accelerate the defrosting process, other than those recommended by the manufacturer.
• Do not store explosive substances such as aerosol cans with a hummable propellant in this appliance.
• The appliance must be immersed.
• This appliance should work under environment of temp from -43’C.
• This appliance is not suitable for installation in an area where a waters could be used.
• Never tum the machine upside down or £an it lolled than 45° .
• Thermostat has be adjusted. No need to adjust it by yourself. When the machine is under the ice point and blocked by ice, the cooling switch crust be closed for 4 lungs before turning it on again to continue its operation.
• This machine should not be turned on until 3 minutes later after turning off the power switch.
•  It i5 recommended to use bottled pure water. Bayou use hard water, may lead to hot pot furring or detonation tank or pipeline risk. If you need cleaning tube, remove scale, need to find a professional institutions and professional operation.
• This product i<; not recommended at an altitude of 1500 meters above the region to use.
• WARNING : When positioning the appliance, ensure the supply cord is not trapped or damaged.
• WARNING : Do not hcate multiple portable socket-outlets or portable power supplies at the rear of the appliance.
• In order to make sure the machine can be used normally, please keep it stand still fur 2A hours before powering up.
• WARNING : UV radiation is dangerous for eyes and skin. Do not operate the UV-C emitter outside the appliance.
• WARNING : Do not operate the UV-C emitter when it is removed from the appliance enclosure.
• WARNING : This appliance contains a UV emitter. Do not stare at the light source.
• Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV-C radiation .UV-C radiation may, even in little doses,-
• cause harm to the eyes and skin.
• Appliance the are obviously damaged must not operated.
• If the replacement of the UV-C emitter by the user is not allowed ,this must be clearly stated.

 OPERATION PANEL

1. Plug the power supply cord into a properly grounded wall outlet, the 3 pilot lamps will light up then go off, one at time, from left to right.

2. Tum on the heating switch. The heating pilot lamp will light up when heating is in progress and will go off when heating is completed and has stopped. The heating pilot lamp will also go off when the heating switch is turned off.

3. Turn on the cooling switch. The cooling pilot lamp will light up when cooling is in progress and will go off when cooling is completed and has stopped. The cooling pilot lamp will also go off when the cooling switch is turned off.

4. Under normal working conditions, after power on. When the UV module is working, the UV pilot lamp will light up. otherwise, the UV pilot lamp will go off.

5. The heating pilot lamp and the cooling pilot lamp will flashing at the same time when the water level in the bottle is low or empty.

GETTING STARTED

Locate Dispenser

1. Place dispenser upright.

2. Locate dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet.
   Notice : DO NOT plug in power cord yet.

3. Position dispenser so the back is at least 20cm from wall and there are at least 20cm of clearance on both sides.

Install Water Bottle

1. Open dispenser door.
2. Place probe assemply on probe hanger.
3. Place fresh bottle outside of cabinet.
4. Remove entire plastic cap from top of bottle.
5. Clean outside of new bottle with a cloth.
6. Place probe into bottle.
7. Slide collar down until it clicks in place.
8. Push head down until tubes hit bottom of bottle.
9. Slide bottle into cabinet and close door.

Provide Electricity

• Plug cord into a properly grounded wall outlet.
• At this time the pump will begin to move water from the bottle to the hot and cold tanks. It will take up to 5 minutes to fill the tanks for the first  time. During this period the pump will run continuously. This is normal.

Activate Heating & Cooling

• Notice : This unit will not dispense hot or cold water until the switches are activated.
• To activate. Push top side of power switches in to start heating and cooling water
• If you do not want to heat water, push bottom side of red switch on.
• If you do not want to cool water, push bottom side of green switch on.

DISPENSING WATER

This unit has been tested and sanitized prior to packing and shipping. During transit dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water.

Dispensing Cold Water
After setup, it will take up to I hour to get water to maximum cold temperature. During this time the compressor could run continuously. This is normal.

1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress normal water control downward to start cold water flow.
3. Release control once desired fill level is achieved.

Dispensing Normal Water

1. . Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control downward to start normal water flow.
3. Release control once desired fill level is achieved.

Dispensing Hot Water
After setup, hot water will be available in 15-20 minutes.

1. Position bottle, glass, pitcher or cooking pot below spout.
2. Slide red button away from you and depress hot water control downward to start hot water flow.
3. Release control once desired fill level is achieved.

UV display
Under normal working conditions, after power on, the UV module starts to work in a 3-hour cycle. In the first 40 minutes, the UV icon lights up and UV function is on. fter 40 minutes, the UV icon goes off and UV function is off. After 140 minutes, the UV icon lights up, UV function is on again, and keep cycling.

Changing Bottles
A flashing red light on your function lights alerts you when your bottle is empty. Replace the bottle as soon as possible.
Notice : Do not dispense hot, cool or cold water if the light is flashing as you could empty the tanks and cause the dispenser to overheat.

1. . Open dispenser door.
2. Slide empty bottle out of cabinet.
3. Remove probe assembly from empty bottle. Place probe assembly on probe hanger.
4. Set empty bottle aside.
5. Place fresh bottle outside of cabinet. Remove entire plastic cap from top of bottle. Clean outside of new bottle with a cloth.
6. Place probe into bottle.Slide collar down until it clicks in place. Push head down until tubes hit bottom of bottle.
7.  Slide bottle into cabinet and close door.

TROUBLE SHOOTING

Water is leaking

• Unplug dispenser, remove bottle and replace it.
• No water is coming from the spout.
• Make sure the bottle is not empty. If empty, replace it.
• Make sure to completely depress the push-button controls.

Cold water is not cold

• It takes up to one hour after setup to dispense cold water.
• Make sure the power cord is properly connected to a working outlet. Make sure the back of the dispenser is at least 20cm from a wall and there is free airflow on all 20cm sides of the dispenser.
• Make sure green power switch on back of dispenser is ON.
• If water stylist’ t cold, please ask for the service agent for assistance.

Hot water is not hot.

It takes 15-20 minutes after setup to dispense hot water.
Make sure the power cord is properly connected to a working outlet. Make sure red power switch on back of dispenser in ON.

Dispenser Is Noisy
Make sure the dispenser is positioned on a level surface.

TECHNICAL PARAMETERS

CIRCUIT DIAGRAM

CLEANING

To avoid accident, cut off the power supply before operation according to the following instruction.

1.  The machine had been disinfected before departed from factory. Cleaning the dispenser prior to installing a full bottle of water for the first time.
2.  Cleaning and draining ins traction:
3. Making sure the power switch m the O(off) position and unplug the water dis panzer before cleaning.
4.  Twist t out the two screws , then take down top cover, rod tank cover and separator 2.
5.  Fill 0.6 gallons pure water into cold tank to clean.
6. Tum on all the taps in tum fur 3 ninutes after the water ou tflow, which completes the internal pipeline flushing.
7.  Place a large water bucket beneath the drain outlet ¾hi.ch on the back of w.iter dispenser, then, remove the drain cover and drain the water 3.
8. Reposition the drain cover, separator, cold tank cover and top cover after draining. Ensure the pipe and wires are connected properly, then, you can use the machine normally.

Attention

1.  The cleaning must be under the guidance of professional staff.

2. The dispenser reads water 1D a temperature of approximately 85°C .It can cause severe bums. Please operate it carefully.

3. Sanitizing
   The machine should be disinfected with the disinfectant separately bought from drugstore or marketplace according to the instruction manual of the disinfectant and then clean it with waiters(see cleaning and draining instruction).Generally
   this should be done every three months.

4. To Remove Mineral Deposits:
   Mix 4 liters water “1th 200g citric acid crystals, inject into the machine and make sure the water can fob out of the hot waiters tap. Switch on the power and heat it about 10 minutes, 30 minutes later, drain off the liquor and clean it with water roe two or three times. Generally this should be done every six months. Never disassemble this machine by yourself 1D avoid danger :&om damaging machine.

MACHINE INSTALLATION

To prevent the machine from swaying to fall, please install the bracket accordingly.

1. Loosen the screw of the left or right bottom angle just as the picture shown.
2. Use the screw to fix the bracket on the left or right bottom angle of the water dispenser.
3. Make a hole on the floor’ s or the desk’ s surface where the water dispenser will be installed.
4. Fix the bracket on the floor by screw tightly.
5. Tighten the screw.

NOTE
Manufacture shall have the right to make changes without prior notice.

The packaging material used is recyclable; we recommend that you separate plastic, paper and cardboard and give them to recycling companies. To help preserve the environment, the refrigerant used in this product is R134a (Hydrofluorocarbon -HFC), which does not affect the ozone layer and has little impact on the greenhouse effect. According to WEEE (Waste of Electrical and Electronic Equipment) guidelines, waste from electrical and electronic devices should be collected separately. If you need to dispose of this appliance in the future, do NOT throw it away with the rest of your domestic garbage. Instead, please take the appliance to the nearest WEEE collection point, where available.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>