DELAVIN 211 Soft Close Sliding Frameless Shower Door Instruction Manual

DELAVIN 211 Soft Close Sliding Frameless Shower Door Instruction Manual

INSTALLATION INSTRUCTIONS

PREPARATION

1. We strongly recommend that this product be installed by a licensed and insured professional contractor, including the assistance of a second person during installation.

2. After opening all boxes and packages, please read this introduction carefully. Check that all required parts are included in the package by marking all components on the Shower Door Components Detail Sheet. Inspect boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that DELAVIN will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed. Feel free to contact DELAVIN if you have any questions.
   Attention: Please double check the glass corners and four edges of the two glass doors to ensure that all glass is in perfect condition and without any breakage. Do not attempt to install a shower door if the glass corners are broken.

3. Please note that if you are in doubt about installation compliance standards, please consult your local building codes. Building and plumbing codes may vary by location and DELAVIN is not responsible for your  project’s code compliance standards and does not accept any returns.

4. Before installation, make sure the installation surface is leveled and solid, and can support the total weight of the unit. Also, make sure the walls are at right angles. Irregular mounting surface levels or improper angle of side walls will cause serious problems during installation. Note that some adjustments and drilling may be required during installation.

5. Protect all major surfaces of the product during installation. Never place glasses directly on tile floors. Leave the corner protector in place until it needs to be removed. Always use a piece of wood or cardboard to protect the bottom edges and corners of the glass before and during installation.

TOOLS REQUIRED

|

|

|

---|---|---|---
Level| Tape Measure| Pencil| Phillips Screwdriver
``| | |
Drill bit| Drill bit| Silicone| Metal File
| | |
Power Drill| Hammer| M itter saw or Hacksaw

(No installation required):Only used for marking hole positions, please place this piece of aluminum on the ground against the wall and mark on the wall according to the holes in the al uminum,then you can make the hole.| 1 pc
10| Side Anti-Water Strip| 1 pc|
11| Screw M4X30| 2 pcs|
TEAR OFF THE GLASS PROTECTIVE FILM BEFORE INSTALLATION**

1. Place the Stationary Glass (8), align the hole above the glass with the Glass Bracket (2) that has been fixed with the stainless steel support rod, Cover the other half of the Glass Bracket (2) to lock the glass (two spacers are placed separately to protect the glass).
   ATTENTION :
   Never set your glass down directly onto a tile or concrete floor.
   Always use a piece of wood or cardboard and leave the corner pads on the glass until it becomes necessary to remove them to protect the bottom edge and the corners of the glass from breakage.
   

2. Place the Measuring Tool(#20) vertically against the wall on the floor, mark the wall according to the holes in the Measuring Tool(#20).
   Drill holes for the Guide Rail Brackets (#1) installation in the determined position and apply silicone into the holes, insert the Wall anchors (#15) for the Guide Rail Bracket.

3. Fix the Guide Rail Bracket(#1) to the wall on both sides with 5*40 screws (#18) as shown in the picture. The other side of the Guide Rail Bracket (#1) is installed in the same way.

4. Detach the Guide Rail Bracket(#1) as shown in the picture to open the connecting rod, then insert the Upper Guide Rail (#5) into the Guide Rail Bracket(#1). Put the Guide Rail Bracket Covers to the Guide Rail Brackets (#1) and secure it tightly with Allen Key（#19）
   

5. Install Glass Door Loosen the Rollers (4) screws and the Install the rollers.
   The Upper roller part is used to connect to the Upper Guide Rail (5) and the lower two parts are used to connect to the Glass Door (17)
   

6. Hang the Glass Door (17) installed with rollers, to the Upper Guide Rail (5). Slide the Guide Block (12) to the bottom of the glass door. Mark down the predrilled position of the guide block. Set the glass door aside. Now drill the hole with drill bit to the threshold. Put the silicone to the hole and then put the wall anchor (15) into the hole. Now secure the guide block to the threshold with Screw M4X30 (11)’

7. Hang the Glass Door (17) back to the Upper Guide Rail (5) , slide the bottom of the glass door into the slot of the Guide Block (12) . Be careful that the glass door should not touch the metal part of the guide block.
   

8. Slide the Side Anti-Water Strip (10) to the Glass Door (17), and slide the 2 pieces Anti-Water Strips (9) with an extended side to the middle glass, cut the extended side that interferes with the Upper Guide Rail (5).
   
   

9. Install the Anti-Splash Threshold (16) in front of the Glass Door (17). Put the Anti-splash threshold in front of the Glass Door (17), and then put the Aluminum Cover with slot （14）into the Stationary Glass (8), on top of the threshold. Mark down the predrilled holes on the threshold, drill the holes with drill bit, put the wall anchor (15). Put slicone sealant to the bottom of the Anti-splash threshold, secure it to the threshold with M4x25 Screw (13) and put the covers back on it.

10. Put the anti-jump buttons removed from step a on page 7 back into the Rollers (4) section
    

11. Tighten the fasteners on both Rollers (4) and Guide Rail Brackets（1） Cover, Glass Bracket（2）.

12. First, split handle ⑦ into two parts as shown in the figure
    

13. Install the handle as shown in the figure
    

14. Apply silicone sealant on the seams between the stationary glass and the shower base, and between the wall and the stationary glass.
    

TUB DOORS INSTALLATION the same as SHOWER DOORS

MUST ALLOW SILICONE TO DRY FOR 24 HOURS BEFORE STARTING USING THE SHOWER

Documents / Resources

| DELAVIN 211 Soft Close Sliding Frameless Shower Door [pdf] Instruction Manual
211 Soft Close Sliding Frameless Shower Door, 211, Soft Close Sliding Frameless Shower Door, Sliding Frameless Shower Door, Frameless Shower Door, Shower Door
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>