MEEC TOOLS 019797 12V 28Nm Screwdriver Instruction Manual

June 3, 2024
MEEC TOOLS

MEEC TOOLS 019797 12V 28Nm Screwdriver

MEEC-TOOLS-019797-12V-28Nm-Screwdriver-PRODUCT-IMAGE

PERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)

Jula reserves the right to make changes.
For latest version of operating instructions, see www.jula.com

EU DECLARATION OF CONFORMITY

Item number: 021737

Jula AB, Box 363, SE-532 24 SKARA, SWEDEN

This declaration of conformity is issued under the sole responsibility of the manufacture

METAL CUTTING BANDSAW
Conforms to the following directives, regulations and standards:

This product was CE marked in year:
Dit product werd CE-gemarkeerd in het jaar: -22

Directive/Regulation Harmonised standard
MD 2006/42/EC EN 60745-1:2009+A11, EN 60745-2-20:2009
EMC 2014/30/EU EN IEC 55014-1:2021, EN IEC 55014-2:2021
RoHS 2011/65/EU + 2015/863 EN 50581:2012

Mattias Lif
BUSINESS AREA MANAGER (Signatory for Jula and authorized to compile the technical documentation.

SAFETY INSTRUCTIONS

WARNING!
Read all warnings, safety instructions and other instructions carefully before use. Failure to follow all the instructions and safety instructions can result in the risk of electric shock, fire and/or serious personal injury. Save these instructions and safety instructions for future reference. The term
“power tool” in all the warnings below refers to mains-powered (corded) or battery-powered (cordless) power tools.

WORK AREA
  • Keep the work area clean and well lit. Dark and cluttered work areas increase the risk of accidents and injuries.
  • Do not use power tools in explosive environments, such as in the vicinity of flammable liquids, gas or dust. Power tools produce sparks that can ignite dust and fumes.
  • Keep onlookers, especially children, and pets at a safe distance when using power tools. You can easily lose control of the product if you are distracted.
ELECTRICAL SAFETY
  • The plug on the power tool must match the power point. Never modify the plug in any way. Never use an adapter with earthed products. Unmodified plugs and matching power points reduce the risk of electric shock.
  • Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
  • Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
  • Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the power point. Keep the power cord away from heat, oil, sharp edges and moving parts. Damaged or tangled power cords increase the risk of electric shock.
  • If using the power tool outdoors, only use an extension cord approved for outdoor use. Cords intended for outdoor use reduce the risk of electric shock.
  • If it is absolutely necessary to use power tools in damp conditions, use a mains connection protected by a residual current device (RDC). Using an RCD reduces the risk of electric shock.

NOTE: When starting the product there may be a temporary voltage drop in the mains supply, which could affect other equipment. Such interference does not normally occur if the impedance in the mains supply Zmax is less than 0.402 ohm. Contact your electricity supplier for more information.

PERSONAL SAFETY

  • Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. Remember that a fraction of a second of inattention or negligence can result in serious personal injury.
  • Use personal safety equipment. Wear safety glasses. Depending on the type of tool and how it is used, safety equipment such as dust masks, non-slip safety shoes, safety helmets and ear protection reduce the risk of personal injury.
  • Avoid accidental starting. Make sure the power switch is in the OFF position before plugging in the plug or inserting the battery, or lifting/carrying the tool.
  • Carrying a power tool with your finger on the switch, or connecting a tool to the mains supply when the switch is in the ON position, increases the risk of accidents and injuries.
  • Remove adjuster keys/spanners before switching on the tool. Spanners or the like that are left in a rotating part of the tool can cause personal injury.
  • Do not overreach. Always maintain a firm footing and good balance. This ensures better control over the power tool in unexpected situations.
  • Wear suitable clothing. Do not wear loose-fitting clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose-fitting clothing, jewellery and long hair can get caught in moving parts.
  • If dust extraction and dust collection equipment is available, this should be connected and used correctly. The use of such devices can reduce the risk of
    dust-related problems.

USING AND LOOKING AFTER POWER TOOLS

  • Do not force the power tool. Use the correct power tool for the planned work. The tool does the job better and more safely when used at the rate for which it was designed.

  • Do not use the power tool if it cannot be switched on and off with the power switch. Power tools that cannot be controlled with the power switch are dangerous and must be repaired.

  • Pull out the plug and/or remove the battery before making any adjustments, changing accessories or putting the power tool away. These safety precautions reduce the risk of accidentally starting the power tool.

  • Store power tools out of the reach of children when not in use. Never allow children, or anyone who is unfamiliar with the power tool and these instructions, to use the tool. Power tools are dangerous if used by inexperienced persons.

  • Maintain power tools and accessories. Check that moving parts are properly adjusted and do not jam, and that no parts are incorrectly fitted or damaged. Check for other factors that could affect functionality. If a power tool is damaged it must be repaired before it is used again.
    Many accidents are caused by poorly maintained power tools.

  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.

  • Use the power tool, accessories and bits etc., in accordance with these instructions, taking into account the actual working conditions and the work that is to be done. It can be dangerous to use power tools for purposes other than those for which they are intended to be used.

  • Keep handles and grips clean, dry and free from oil and grease. Greasy handles and grips make it difficult to hold and control the tool in unexpected situations.

USING AND MAINTAINING BATTERY­POWERED TOOLS
  • Only charge the battery with the charger recommended by the manufacturer. Charging other batteries can result in a risk of personal injury and/or fire.
  • Only use batteries recommended by the manufacturer. The use of other batteries can result in a risk of personal injury and/or fire.
  • When the battery is not in use keep it away from metal objects such as paperclips, coins, keys, nails, screws and other small metal objects that can short circuit the terminals. Short circuiting discharges large amounts of energy that can cause a fire and/or burn injuries.
  • Failure to handle the battery carefully can cause fluid to leak from the battery. Avoid contact with battery fluid. On contact with battery fluid, rinse immediately with plenty of fresh water. Seek medical attention if you get battery fluid in your eyes. Battery fluid can cause skin irritation and/or burns.
  • Do not use damaged or modified batteries, or power tools that are damaged. Damaged or modified batteries can behave unexpectedly and cause a fire, explosion or risk of personal injury.
  • Do not expose batteries or power tools to naked flames or heat. Batteries can explode when exposed to naked flames or temperatures higher than 130°C.
  • Follow the instructions for charging and charge the battery only at the temperature indicated in the instructions. Incorrect charging or charging outside the given temperature range can damage the battery and cause a fire.
SERVICE
  •  The power tool must only be serviced by qualified personnel using identical spare parts. This will ensure that the power tool remains safe to use.

SAFETY INSTRUCTIONS FOR CORDLESS SCREWDRIVER

  • Hold the power tool by the insulated grips when working in areas where the tool could come into contact with concealed electrical cables or its own power cord. Contact with a live cable will cause the metal parts on the power tool to also become live – risk of electric shock.

SAFETY INSTRUCTIONS FOR USE OF LONG DRILLS

  • Never work with a speed higher than the rated speed for the drill. At higher speed there is a risk that a freely rotating drill without contact with the workpiece can bend and cause personal injury.
  • Always start drilling at low speed and with the tip of the drill in contact with the workpiece. At higher speed there is a risk that a freely rotating drill without contact with the workpiece can bend and cause personal injury.
  • Only apply pressure in line with the drill. Do not press too hard. The drill can bend, which can cause it to break, or that you loose control of the tool, and result in personal injury.

ACCESSORIES/ATTACHMENTS

  • Only use the accessories and attachments specified in the instructions and which are compatible with the product.
SAFETY INSTRUCTIONS FOR BATTERY CHARGER
  • This product can be used by children from 8 years of age and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Keep children under supervision to make sure they do not play with the tool. Do not allow children to clean or maintain the tool without supervision.
Symbols

The following symbols can be of importance for how you should use your power tool. Make sure you understand the symbols and their significance.

|

Read the instructions.

---|---

CE

| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.

Always wear ear protection!
The declared values for vibration and noise, which have been measured according to a standardized test method, can be used to compare different tools with each other and for a preliminary assessment of exposure. The measurement values have been determined in accordance with EN 60745-2-20:2009.

WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

TECHNICAL DATA
  • Voltage 12 V
  • Torque 28 Nm
  • Speed 0-400 / 0-1300 rpm
  • Chuck size 10 mm
  • Capacity in wood 16 mm
  • Capacity in steel 6 mm
  • Size L 16.8 x H 17.5 x D5.8 cm
  • Sound pressure level, LpA 71.1 dB(A), K= 5 dB
  • Sound power level, LwA 82.1 dB(A), K= dB
  • Vibration level 1.987 m/s², K= 1.5 m/

DESCRIPTION

Two speed screwdriver included in Meec Tools Multiseries 12 V. With integrated LED, rubber coated grips and 20+1 torque settings. Battery and battery charger sold separately.
The product is intended for drilling and screw driving in wood, plastic and metal. The product must only be used for its intended purpose and in accordance with these instructions. All other use is considered to be unsuitable. Incorrect use, inadequate maintenance and/or illicit use of the product can result in serious personal injury and/or material damage. The manufacturer cannot accept liability for personal injury or material damage resulting from improper use. The product is only intended for household use.

  1. Power switch with speed control
  2. Rotoation selector
  3. Keyless chuck
  4. Torque cover
    FIG. 1

ASSEMBLY

PREPARATIONS

Inserting/removing the battery

  • The battery is only partially charged on delivery. The battery must be charged before the power tool can be used. Lithium-ion batteries can be charged at any time without affecting their lifespan. Interrupting the charging will not damage the battery.
  • Charging temperature: 10 to 40°C. Check the battery charge status at regular intervals if the product has not been used for some time. The optimum charge is 50 to 80%. Store the tool in a dry place. Storage temperature: 0 to 25°C.

IMPORTANT: Pull out the charger plug from the power point before the battery is connected to, or disconnected from the charger.

  1. Press the battery lock and pull the battery  out directly.
    FIG. 2

    1. Put the battery in the battery charger.
  2. Plug in the plug. The red charging indicator light goes on.

  3. The green charging indicator light goes on when the battery is fully charged.
    FIG. 3

  4. Replace the battery in the product.
    The battery can be hot after use. Allow the battery to cool before charging.
    FIG. 4MEEC-TOOLS-019797-12V-28Nm-Screwdriver-03

Checking the battery charge
The charging indicator light shows the battery status as follows when the product is started. Red, orange and green = fully charged.
Red and orange = partially charged.
Red = discharged. Charge the battery.

Replacing bits/accessories
The product has an automatic spindle lock.
The drive unit is locked when the motor has stopped and the quick chuck can be opened by twisting it clockwise. Insert the required bit/accessory and twist the chuck anticlockwise. The spindle lock is released automatically when the motor starts (power switch pressed).
Fig 5

2 gears

IMPORTANT: Do not move the mode selector when parts are rotating, this can damage the product.

Gear 1 (mode selector in position 1)

Speed up to approx. 400 rpm and right-hand torque. This mode is suitable for screwdriving.

Gear 2 (mode selector in position 2)
Speed up to approx. 1300 rpm. This mode is suitable for drilling.

Removing the chuck
The keyless chuck must be removed to use the bit adapter.

Removing the chuck
  1. Firmly grip the keyless chuck from the front.
  2. Press the chuck ring against the chuck.
  3. The chuck releases and can be pulled loose.
Fitting the chuck
  1. To replace the chuck, pull the chuck ring towards the chuck.
  2. Put the chuck over the bit adapter.
  3.  Release the chuck ring so that the chuck clicks in place.

NOTE: If the chuck does not click in place automatically, twist the chuck ring.

Using the bit adapter

The bit adapter can be used when the chuck has been removed.

  1. Put the required bit in the bit adapter.
  2. Press in the bit as far as it goes in the bit adapter.
  3. The guides and magnetic holder hold the bit firmly in place.
  4. Pull the bit out of the bit adapter.

USE

DIRECTION SELECTOR/POWER SWITCH LOCK

Release the power switch lock and change the direction of rotation by moving the direction selector to the left or right.

Switching on/off

Starting
Start the product by pressing the power switch and holding it in. The work light goes on when the power switch is fully or partly pressed. The work light simplifies working in dark areas.
FIG. 6

MEEC-TOOLS-019797-12V-28Nm-Screwdriver-04

Switching off
Switch off the product by releasing the power switch.

Adjusting the speed
The power switch on the product provides variable speed control. Press the power switch a little for low speed. The speed increases the more the switch is pressed.
FIG. 7

NOTE:
The integrated brake function in the motor ensures quick stop.

Mode selector
Use speed mode 1 (low speed) for small screws.
Use speed mode 2 (high speed) for large screws.
FIG. 8

Rotation selector
Move the rotation selector to the left to screw in screws.
Move the rotation selector to the right to unscrew screws.
FIG. 9

Torque setting ring
Set the required torque with the torque setting ring.

  • Set a low torque for small screws and/or soft material.
  • Set a high torque for large screws and/or hard material, and for unscrewing screws.
  • Set the drilling mode by twisting the torque setting ring to the position that shows a drill.
  • Move the mode selector forward for drilling (mode 2).
    FIG. 10

Activate power switch lock
Move the direction selector to the mid point.
This locks the power switch.

TIPS AND TRICKS

  • Always check before use that the bit is correctly fitted and centred in the chuck.
  • Screw bits are marked with size and shape. If unsure, check if the bit fits the screw head without any play.

Torque
Small screws can be damaged if they are driven with high torque or speed.

Screw unions in hard materials (for example metal)
The torque is very high for metal screw unions tightened with screw sleeves. Use a low speed.

Screw unions in soft material (for example soft wood)
Use a low speed to avoid damaging the wood on contact with the screw head. Countersunk screw hole

Note the following points when drilling in wood, metal and other materials

  • Use high speed for drills with a small diameter and low speed for drills with a large diameter.
  • Use a low speed for hard materials and a high speed for soft materials.
  • Secure the workpiece if possible with clamps, clips or in a vice.
  • Mark the drilling point with a punch. Start drilling at low speed.
  • Pull out the rotating drill from the hole now and then to remove dust and shavings and to clean the hole.

Drilling in metal
Use a high speed steel drill intended for metal. Use coolant for best results. Metal drills can also be used for drilling in plastic. Drill first with a 3 mm diameter drill and then with a drill with the required diameter.

DRILLING IN WOOD
Use a centre drill. Use a twist drill for deep holes, and use a pin drill for holes with a large diameter. Small screws can be driven in soft wood without predrilling.

MAINTENANCE

WARNING!
RISK OF PERSONAL INJURY Switch off the product and remove the battery before cleaning and/or maintenance.

The product is maintenance-free.

  • Keep the product clean, dry and free from oil and grease.
  • Make sure no liquid gets into the product.
  • Use a soft, dry cloth to clean the casing. Do not use petrol, solvent or detergent that can damage the plastic parts.
  • Check the battery charge status at regular intervals if the product has not been used for some time. The optimum charge is 50 to 80%. Store the product in a cool and dry place.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals