havit HV3223T-WHT Seefore Polycarb White LED Step Light Instruction Manual
- June 5, 2024
- havit
Table of Contents
havit HV3223T-WHT Seefore Polycarb White LED Step Light
Polycarbonate Step Light Installation Instructions
Product Specifications
Model No.| HV3221T-BLK| HV3221T-WHT| HV3222T-BLK|
HV3222T-WHT| HV3223T-BLK| HV3223T-WHT| HV3225T-BLK|
HV3225T-WHT
Name| Seefore| Service
Material| Polycarbonate
Color| Black| White| Black| White| Black| White| Black| White
IP Rating| IP65
Input Voltage| 12v DC
Protection Class| (Low Voltage)
Lamp Base| Built in LED
Lamp Wattage| 1x 3w| 1x 5w
Color Temp| TRI Color – 3000k, 4000k, 5500k| TRI Color – 3000k, 4000k, 5500k
Lumens| 90lm, 95lm, 100lm| 150lm, 155lm, 160lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
HV3221 Dimensions| HV3222 Dimensions| HV3223
Dimensions| HV3225 Dimensions
|
| 
|
HV3221 Mounting Base
HV3223 Mounting Base
HV3222 Mounting Base
HV3225 Mounting Base
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- All O-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Remove face from base plate
- Remove screws and clear cover from front of fitting as set aside.
- Install base plate in desired location, Seal all holes in the backing plate including cable entry and screw holes.
- Using an appropriate 12v LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Fitting is preset to 3000k, To change move switch above PCB to desired color temperature
- Reattach clear cover making sure screws are tight to avoid water penetration.
- Reattach face onto fitting.
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions***
Additional Information
Documents / Resources
|
havit HV3223T-WHT Seefore Polycarb White LED Step
Light
[pdf] Instruction Manual
HV3223T-WHT, Seefore Polycarb White LED Step Light, White LED Step Light, Step
Light, HV3223T-WHT, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>