Porta PT-WC-012N Two Piece Toilet Installation Guide
- June 28, 2024
- PORTA
Table of Contents
PT-WC-012N Two Piece Toilet
Product Information
Specifications
- Product Type: Two-Piece Toilet
- Model Number: Not specified
- Manufacturer Contact : kilitde980@outlook.com
Product Usage Instructions
SUGGESTED TOOLS AND MATERIALS
Before Installation
Inspect the toilet for damages, ensure compliance with plumbing codes, and
remove the old toilet. Make sure the mounting surface is clean and level
before proceeding.
- Inspect the toilet to ensure no damages have occurred while in shipping.
- Observe all plumbing and building codes by your
- state and local requirements.
- Remove the old toilet.
- Make sure the mounting surface is CLEAN and LEVEL.
General Recommendations
Read the installation and maintenance instructions thoroughly. Use proper
tools and wear personal safety accessories for protection. Please read the
installation and maintenance instructions thoroughly before installing the
toilet. Be sure to use proper tools and always wear proper personal safety
accessories for your protection.
PARTS LIST.
Tank lid, water fitting, soft-close toilet seat, bolts kit, wax ring,
installation instruction.
- Read the complete instruction manual before beginning installation.
- Confirm that your model will fit in the intended location and that plumbing fixtures are located where legally required before beginning installation.
- Not all drawings in this manual are drawn to scale. Please refer to the model chart.
- Two people are recommended to install and move this product.
- The product is FRAGILE! To avoid breakage and possible injury handle with care.
NOTE: Drawings may not exactly define the contour of the product.
Installation Steps
Step 1: Wax Ring Installation
Insert new toilet bolts in the slotted flange with bolt heads down. Place
the toilet bowl upside down on a soft material. Apply the wax ring evenly
around the waste flange with the tapered end facing the toilet. Apply a thin
bead of sealant around the base.
Step 2: Bolts and Nuts
Insert new toilet bolts in the slotted flange with bolt heads down. Place
the wax ring evenly around the waste flange. Apply sealant around the toilet
base. Avoid over-tightening nuts to prevent damage.
IMPORTANT – DO NOT OVER TIGHTEN NUTS! Over-tightening the nuts can cause chips and cracks.
NOTE: Drawings may not exactly define the contour of the product.
Step 3: Water Supply Connection
Connect the water supply line to the supply valve. Place the washer inside
the coupling nut and screw it onto the toilet water inlet. Tighten all nuts
securely without over-tightening to avoid chips and cracks. Carefully remove
the tank and lid. Gently place the tank
upside down on a soft material to prevent scratching. Please make sure the
large washer (doughnut) is installed correctly. lt should fit snugly over the
plastic lock nut on the threaded tank outlet. Remove the plastic nut and metal
washer, Place the tank on the toilet bowl with the large doughnut washer
centre on the bowl inlet. From underneath, a metal washer and plastic nut to
each bolt were left loose for adjustments. Verify the tank is parallel to the
wall and slightly tighten the plastic nutsalternatingback and fort until the
tank is in contact with the bowl piers.
IMPORTANT
DO NOT OVER TIGHTEN NUTS! Over-tightening the nuts can cause chips and
cracks.
Step 4: Tubing Connection
If the plastic tubing comes out of the overflow tube, connect it from the
water inlet regulator tip to its holding ring inside the overflow tube. Trim
excess tubing if needed to eliminate leaks. Connect the water supply line (not
included) to the supply valve. Place the washer inside the coupling nut and
screwonto the toilet water inlet. lf necessary, slightly bend the supply line
to reach the water inlet. Tighten all nuts securely.
Step 5:
lf the plastic tubing comes out ofthe overflow tube please connect the plastic
tubing from the tip of the water inlet regulator into its holding ring inside
the overflow tube. lf necessary,- excess may be trimmed to eliminate any
leaks.
Step 6:
Remove the lever and nut from the parts bag. insert the lever through the
hole in the tank. thread the nut onto the threaded shank. (Left-handed evers
will turn clockwise; Righthandeoevers furn counterclockwise.) Tighten the nut
with a wrench until snug.
NOTE : Skip this step if the lever is already installed.
Step 7:
Turn on the supply valve and check for leaks. Flush the toilet and let the
toilet complete one cycle. Adjust the water level as needed to ensure it
rea:hes the water level line marked inside the toilet.
- Raise water level: Turn the flow adjusting screwlockwise.
- Lower water level: Turn the flow adjusting the screw counterclockwise.
Step 8:
Place the cover on the tank. Instal the toilet seat according to the
manufacturer’s instructions.
NOTE: Drawings may not exactly define the contour of the product.
Step 9:
Care and Cleaning of Vitreous China
Your new toilet is made of stain, acid and abrasion-resistant vitreous china.
But, like all fine finishes, china requires reasonable care. For day-to-day
cleaning, wash with warm water, a soft cloth, and a mild detergent, On
stubborn stains, use one of the powdered detergents, on a damp sponge or
scouring pad of ylon, saran, or poly-ethylene. Never use abrasive scouring
powders,- cleansers, or pads as they tend to create microgrooves that dull the
finish and allow it to work into the surface. Use of tank cleaning products
containing calcium hypochlorite (chlorine) or any other reactive chemical
shall constitute improper maintenance and may void the warranty.
Step 10:
Please keep this manual for future reference. Retain product invoice.
Record the Mode Number ofthe toilet in this booklet. This will assist when
ordering replacement parts.
NOTE: Drawings may not exactly define the contour of the product.
LIMITED WARRANTY COVERAGE
1 YEAR TOILET BOWL & TANK
We warrant its toilet bowl & Tank against fading/staining of the glaze as a
result of a deflection in materials and workmanship for one (1) year from the
purchase date. SCRATCHES ARE NOT COVERED UNDER WARRANTY.
1 YEAR TOILET SEAT ·1 YEAR FILL VALVE & FLUSH VALVE ·1 YEAR PLUMBING
PARTS
We warrant factory-installed plumbing parts fittings, and electrical
components to be free from defects in materials and workmanship for one (1)
year from the purchase date.
The manufacturer warrants this product to be free of manufacture defects during the above-mentioned warranty time. Please keep a copy of the original invoice as proof of purchase. We will, as an option,(1) repair or replace the defective part(s) or product(s) at no charge, (2) issue a refund of the original purchase price of the product(s) (Valid within 30 days from the date of purchase), or (3) issue a credit to be applied toward the purchase of a new product Shipping/delivery charges may apply and are at our sole discretion. Our products must be installed by a fully insured and licensed plumber only. Installation of any of our products by anyone other than a fully insured and licensed plumber shall void the limited warranty. This limited warranty shall not apply to goods that have been subject to accident, negligence, improper installation, product abuse, product misuse, or use of cleaners containing abrasives , alcohol or other organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this warranty. Our responsibility under this limited warranty is limited to only replacement parts and no other costs. We will not be responsible for labour charges and/or damage incurred by installation, repair or replacement, nor for any indirect incidental or consequential damages, losses, injury or costs of any nature relating to this product. Except as provided by law, this limited warranty is instead of and excludes all other warranties, conditions, and guarantees, whether expressed or implied, statutory or otherwise, including without restriction those merchantability of fitness for use.
RESPONSIBILITIES OF OTHERS
Inspecting the unit before installation is the responsibility of the
installer or building contractor who acts on behalf of the user. They are
responsible for ensuring the unit is free of defects or damage. Notices are
placed on and in the unit and on the shipping carton advising the installer of
this responsibility. In the event of a problem, the unit must not be
installed. We are not responsible for failures or damage that could have been
discovered, repaired, or avoided by proper inspection and testing before
installation. Damage occurring in transit is the responsibility of the
carrier. The user or installer MUST open the crate and inspect the unit for
damage when it is delivered. If damage is discovered, it must be reported
immediately to the seller and the carrier in writing, and an inspection
requested. Failure of the carrier to respond should be reported to the seller
and the carrier. Your freight claims should be filed promptly thereafter.
LIMITATIONS AND EXCLUSIONS
This warranty does not cover any claim arising from abuse, misuse, negligence,
accident, improper installation, or operations on the part of the purchaser.
This warranty is void if the product is subject to alteration, or if repairs
are attempted by anyone other than an authorized agent of ours. This warranty
does not extend to plumbing or components installed by dealers, installers, or
by any party other than us. We will not be liable for loss of use of the
product inconvenience, or any other incidental or consequential costs,
expenses or damages. Please note that some states do not allow the exclusion
or limitation of incidental damages.
DISCLAIMER
Except as expressly provided, there shall be no warranty or obligation,
express or implied, oral or statutory. No dealer or other person has the
authority to make any warranties or representations concerning our company or
its products. In no event shall we be held responsible for any such warranties
or representations?
WARRANTY SERVICE
NOTE: When requesting a warranty, be sure to have the following:
- Copy of original invoice
- Date of installation
- Description and pictures of the defect
- Model number or description of the model
To obtain warranty service and replacement parts, please contact our Customer Service. We will determine whether to repair or replace your product, issue a refund, or issue a credit.
FAQ (Frequently Asked Questions)
Q: Can one person install the two-piece toilet alone?
A: It is recommended to have two people for installation and moving due to the
product’s fragile nature.
Q: Why is it important not to over-tighten nuts during installation?
A: Over-tightening nuts can cause chips and cracks in the product, leading
to potential damage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>