PORTA PHONE ULP16-RD Dual Speaker User Guide
- June 14, 2024
- PORTA PHONE
Table of Contents
PORTA PHONE ULP16-RD Dual Speaker
Product Information
Specifications
- Model No.: ULP16-RD (Dual speaker)
- FCC Compliance: Part 15 of FCC Rules
Product Usage Instructions
Talking and Listening
To use the ULP16-RD device for talking and listening, please follow the steps
below:
- Ensure that the device is powered on and properly connected.
- Adjust the volume to a comfortable level using the volume control buttons.
- Place the device close to your ear for optimal sound quality.
- Speak directly into the device’s microphone for clear communication.
- If you experience any interference or undesired operation, try adjusting the position of the device or moving away from potential sources of interference.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Hearing Protection
To prevent possible hearing damage, it is important not to listen at high
volume levels for long periods. Excessive exposure to loud sounds can cause
permanent hearing loss. Please use the device responsibly and take breaks when
necessary.
FAQ (Frequently Asked Questions)
-
Q: How do I adjust the volume on the ULP16-RD device?
A: To adjust the volume, use the volume control buttons located on the device. Press the “+” button to increase the volume and the “-” button to decrease the volume. -
Q: What should I do if I experience interference or undesired operation?
A: If you encounter interference or undesired operation, try adjusting the position of the device or moving away from potential sources of interference. Additionally, ensure that the device is properly connected and powered on.
Power ON/OFF
- Power ON: Press and hold the power button till to GREEN LED blinks or lights up.
- Power OFF: Press and hold the power button till to the RED LED flashes.
Pairing (Register mode)
- Press and hold the power button to turn the headset power ON, the power LED should blink in Green color.
- Enter the pairing mode: Press the volume down button 3 times continually, then press and hold the volume up till to the RED and Green LED blink alternately.
- The main headset enters the pairing mode first then also the Remote to pairing mode.
- The Green LED of the Remote headset will blink quickly and then turn off after paired, press the power button to quit the pairing mode and keep the Main headset on the pairing mode can pair with more Remotes, or press the power button to quit pairing mode.
- Repeat the above step “d” for more Remote headsets paired with the same Main headset, or press the power button to finish the pairing(register).
- Press SW of the Main headset can make a total of 15 Remote headsets registered in 2 separate groups. The Main headset can accept a maximum of 15 remotes registered in full duplex, the power LED will flash in an ORANGE color when the register remote reaches 15., press the power button to quit the pairing mode)
Talking and listening
- The main headset and remote headset will start to search each other after powering ON, the GREEN LED flashes 1 time every 3 seconds. The headset will be linked together automatically when the pairing ID is confirmed by the main headset and the LED turns ON in GREEN color.
- Press the volume up and down button to adjust the headset speaker sound volume.
CONFERENCE on MAIN
Press the switch located lower side of the ear cup to make 15 headsets to separate 2 groups or all in CONFERENCE if the remote headset has registered in 2 groups.
Mic Muted
The headset Microphone stopped automatically when the Mic boom swiveled up.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Warning:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
The device has been tested and complies with FCC/ISEDC SAR limits. To prevent possible hearing damage, do not listen at high volume levels for long periods.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>