HAMPTON BAY HD5887E3 1-Light Flush Mount User Guide

: October 30, 2023
: HAMPTON BAY

Table of Contents

HAMPTON BAY HD5887E3 1-Light Flush Mount
Product Usage Instructions
Safety Information
Warranty
Pre-Installation
- PACKAGE CONTENTS
Installation
Care and Cleaning
Troubleshooting
Service Parts
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HAMPTON BAY HD5887E3 1-Light Flush Mount

Product Usage Instructions

Read and save the instructions provided in the manual for your protection and safety.
Before attempting to assemble, install, or operate this product, carefully read and understand the information provided in the manual completely.
To avoid any hazards, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit before starting the installation of this fixture or removal of a previous fixture. Tape a sign to the panel warning others to leave the circuit alone while you work.
Use a voltage tester to make sure that the wire is not live before touching any wire.
Make sure your hands and feet are dry when replacing fuses, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch the plug fuse only by its insulated rim, and remove the cartridge fuses with a fuse puller.
Use tools with insulated handles and ladders made of wood or fiberglass.
Place a safety cover over any unused outlets to protect children.
If you have any electrical questions, consult a qualified electrician. For non-electrical questions about this fixture, please call the Customer Service Team at 1-855-HD-HAMPTON or visit HAMPTONBAY.COM. Please reference the model and item numbers.
Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call the Customer Service Team at 1-855-HD-HAMPTON.

THANK YOU

We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this light fixture. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!

Safety Information

READ AND SAVE THESE INSTRUCTIONS

For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install, or operate this product. Failure to do so could lead to electrical shock, fire, or other injuries that could be hazardous or even fatal.
Before touching any wire, use a voltage tester to make sure it is not live.
When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch the plug fuse only by its insulated rim. Remove the cartridge fuses with a fuse puller.
Use tools with insulated handles and ladders made of wood or fiberglass.
To protect children, place a safety cover over any unused outlets.

DANGER: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.

CAUTION: Consult a qualified electrician if you have any electrical questions. If you have any non-electrical questions about this fixture, please call our Customer Service Team at 1-855-HD-HAMPTON or visit HAMPTONBAY.COM. Please reference the model and item numbers.

Warranty

THREE (3) YEAR WARRANTY

WHAT IS COVERED

The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

WHAT IS NOT COVERED

The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Pre-Installation

PLANNING INSTALLATION

Read all instructions before installing.
To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.

IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call the Customer Service Team at 1-855-HD-HAMPTON.

NOTE: This product requires one 60W maximum medium base (E26) type “A” or type “S” or 9W maximum medium base (E26) self-ballasted LED vintage Edison bulb (sold separately).

TOOLS REQUIRED (NOT INCLUDED)

HARDWARE INCLUDED

NOTE: Hardware is not shown to actual size.

Part	Description	Quantity
AA	Crossbar assembly

(Pre-assembled to fixture body)

| 1
BB| Outlet box screw| 2
CC| Wire connector| 3
DD| Lock screw

(Pre-assembled to fixture body)

| 2

PACKAGE CONTENTS

Part	Description	Quantity
A	Fixture body	1

Installation

Preparing the crossbar assembly

Unscrew the mounting screws (DD) from the crossbar assembly (AA), remove the crossbar assembly (AA) from the fixture body (A), and keep the mounting screws (DD) for later use.

Installing the crossbar assembly

Secure the crossbar assembly (AA) to the outlet box (not included) with outlet box screws (BB). Tighten until snug.

NOTE: The tab on the crossbar should protrude outward.

Making the electrical connections

Use wire connectors (CC) to connect the wires.

Ground Wire:
- Wrap the supply ground wire around the green ground screw on the crossbar assembly (AA), no less than 2 in. from the end of the wire. Tighten the ground screw.
- Connect the fixture ground wire to the supply ground wire with a wire connector (CC).
Supply Wire:
- Connect the supply white wire to the white fixture supply wire with a wire connector (CC).
- Connect the supply black (or red) wire to the black fixture supply wire with a wire connector (CC).
- Wrap each connection with approved electrical tape and carefully insert all of the connected wires into the outlet box.

Attaching the fixture body to outlet box

Line up the holes on the canopy of the fixture body (A) and the mounting holes on the crossbar assembly (AA).
Secure with the mounting screws (DD). Tighten until snug.

Installing the light bulb

Install the correct bulb (not included) referring to fixture markings and/or labels for maximum wattage.

NOTE: Use one 60W maximum medium base (E26) type “A” or type “S” or 9W maximum medium base (E26) self-ballasted LED vintage Edison bulb (sold separately).

Care and Cleaning

Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box, and use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.

Troubleshooting

Problem	Possible Cause	Solution
The light(s) will not turn on.	The bulb is burned out.	Replace the light

bulb.
The power is off.| Ensure the power supply is turned on.
There is a faulty switch.| Test or replace the switch.
There is a faulty wire connection.| Check the wiring.
The fuse blows or the circuit breaker trips when the light is turned on.| There are crossed wires, or the power wire is grounding out.| Discontinue use of the light.

Check the wire connections.

Contact a qualified electrician or call the Customer Care Service Team at 1-855-HD-HAMPTON.