PORTA PHONE ULP16-MD Dual Speaker User Guide

PORTA PHONE ULP16-MD Dual Speaker

Product Information

Specifications:

• Model No.: ULP16-MD (Dual speaker)

Product Usage Instructions

Talking and Listening
To use the ULP16-MD, follow the steps below:

1. Ensure that the device is charged and turned on.
2. Pair the device with your smartphone or other compatible device via Bluetooth.
3. Once paired, you can use the ULP16-MD for both talking and listening.
4. To make a phone call, use the controls on the device to dial the desired number or use voice commands if supported by your connected device.
5. During a phone call, speak into the built-in microphone located on the device.
6. To listen to audio, such as music or podcasts, play the audio on your connected device, and it will be transmitted through the ULP16-MD’s dual speakers.
7. Adjust the volume using the controls on the ULP16-MD. Be mindful not to listen at high volume levels for long periods to prevent possible hearing damage.

FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FAQ (Frequently Asked Questions):

Q: How do I pair the ULP16-MD with my smartphone?
A: To pair the ULP16-MD with your smartphone, follow these steps:

1. Turn on the ULP16-MD and ensure it is in pairing mode. Refer to the user manual for specific instructions on how to enter pairing mode.
2. On your smartphone, go to the Bluetooth settings menu.
3. Scan for available devices.
4. Select the ULP16-MD from the list of available devices.
5. Follow any additional prompts on your smartphone to complete the pairing process.

• Q: How do I adjust the volume on the ULP16-MD?
  A: To adjust the volume on the ULP16-MD, use the volume controls located on the device. These controls allow you to increase or decrease the volume as desired.

• Q: Can I use the ULP16-MD with devices other than smartphones?
  A: Yes, you can use the ULP16-MD with other compatible devices such as tablets, laptops, or any device that supports Bluetooth audio connectivity.

Power ON/OFF

• Power ON: Press and hold the power button till to GREEN LED blinks or lights up.
• Power OFF: Press and hold the power button till to the RED LED flashes.

Pairing (Register mode)

• Press and hold the power button to turn the headset power ON, the power LED should blink in Green color.
• Enter the pairing mode: Press the volume down button 3 times continually, then press and hold the volume up  till to the RED and Green LED blink alternately.
• The main headset enters the pairing mode first then also the Remote to pairing mode.
• The Green LED of the Remote headset will blink quickly and then turn off after paired, press the power button to quit the pairing mode and keep the Main headset on the pairing mode can pair with more Remotes, or press the power button to quit pairing mode.
• Repeat the above step “d” for more Remote headsets paired with the same Main headset, or press the power button to finish the pairing(register).
• Press SW of the Main headset can make a total of 15 Remote headsets registered in 2 separate groups. The Main headset can accept a maximum of 15 remotes registered in full duplex, the power LED will flash in an ORANGE color when the register remote reaches 15., press the power button to quit the pairing mode)

Talking and listening

• The main headset and remote headset will start to search each other after powering ON, the GREEN LED flashes 1 time every 3 seconds. The headset will be linked together automatically when the pairing ID is confirmed by the main headset and the LED turns ON in GREEN color.
• Press the volume up and down  button to adjust the headset speaker sound volume.

CONFERENCE on MAIN

Press the switch located lower side of the ear cup to make 15 headsets to separate 2 groups or all in CONFERENCE if the remote headset has registered in 2 groups.

Mic Muted

The headset Microphone stopped automatically when the Mic boom swiveled up.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Warning:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device has been tested and complies with FCC/ISEDC SAR limits. To prevent possible hearing damage, do not listen at high volume levels for long periods.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>