MOMAN CP2 1-Trigger-2 Wireless Phone Microphone User Manual

June 12, 2024
MOMAN

CP2
1-Trigger-2
Wireless Phone Microphone

MOMAN CP2 1-Trigger-2 Wireless Phone Microphone

‘Thank you for choosing MOMAN product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your MOMAN Product

  • Please keep the product in a dry, clean, dust-free environment
  • Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
  • Use only a soft and dry cloth for leaning the product.
  • Malfunction may be caused by dropping, impact of external force.
  • Do not attempt to disassemble the product. Doing 5o voids warranty.
  • Please have the product checked of repaired by authorized technicians if any malfunctions happened.
  • Failure to follow all the instructions may result in mechanics damage.
  • Warranty does not apply to human errors.

Package List

MOMAN CP2 1-Trigger-2 Wireless Phone Microphone - Package
list

Product Introduction

Transmitter
(1) Foam Windscreen
(2) Transmitter Indicator Light
(3) Transmitter Charging Port
(4) Clip
(5) Power/Mute Button

Receiver
(6)  Phone Connector(Type-C or Lightning)
(7) Receiver Indicator Light
(8) Type-C or Lightning Port
(9) Strap Hole

Charging Case
(10)  Charging Case Indicator
(11) Type-C Charging Port

Indicator- TX Transmitter

Function/Status Operation Light
Power on Press power button 3s Green keep on
Power off Press power button 3s Light off
Unconnected / Red and green lights flash alternately
Connected / Red light off green light on

Switching noise
reduction| Switching with the click
of power button| Level 1: Green light flashes 1 time
Level 2: Green light flashes 2 times
Level 3: Green light flashes 3 times
Reverberation| /| Red light flashes once then green light on
Mute| Double click on the power button to mute and double click again to resume| Green light flashing, Red light off
Charging| /| Red ight on, Green light off
Fully charged| /| All light off
Low battery| /| Fed light flashes once every 105 Green light off

* Indicator- RX Receiver

Function/Status Operation Light
Power on Plug into devices ports Red light Flash
Power off Pull out devices ports Light Off
Unconnected / Red light Flash
Connected / Red light keep on

Indicator- Charging Case

Function/Status Light
Charging & Fully Charged White flashes. The flashing light moves in

proportion to the charge until it is fully charged.
Low Battery| Power indicator lights up for 5S and then turns off

Operation

. TX

  1. Power On/Off
    On: Press the Power/Mute Button once.
    Off: Long press the Power Mute Button for 3s.

  2. Pairing
    With two transmitters ON, plug the receiver into device and the system will pair automatically
    ※ If the TX and RX are not connected or you need 1o replace the RX, re-pairing is required.
    (1) With one TX ON, long press the Power/Mute Button for 8s until the the green light flashes quickly. Plug in the RX until the green light is on.
    (2) Plug out the RX. Follow step(1) to pair the other TX and plug in the RX again until the green light is on. When indicators of both TX show green, two- transmitter-one-receiver pairing is successful
    Note: Before TX pairing, do not plug RX into device and power it. Otherwise, the
    pairing may not be successful

  3.  Mute
    After pairing, press the Power/Mute Button once to mute. Press it again to cancel mute.

  4. Charging
    Place the TX in the case with contacts connected with the case’s OR charge them via charging cable. Please fully charge the TX transmitter with charging cable before use.

  5. Noise Reduction
    One Click off the button cycles through up to 3 levels of noise reduction and original sound in sequence, with a memory function that remembers the noise reduction level before the last switch off

  6. Reverberation
    The new Reverb function optimizes your sound and makes it more three- dimensional. Three clicks of the button toggles the reverb, which is not on by default, but needs to be tuned on manually, and exits the reverb after three
    clicks again.

* RX

  1. Power On/Off
    On: Plug in the device
    Off: Plug out of the device

  2. Connecting
    Connect the receiver to phone.
    ※ Use the Type-C to USB Adapter to connect with computer.
    ※ OPPOVIVO/IQOO/Realme mobile phones can be used normally only when OTG function ( please search “OTG” on the settings) turns on

  3. Pairing
    With two transmitters ON, plug the receiver into device and the system will pair automatically

  4. Charging
    There is no battery in RX receiver and no need 1o recharge during live. If the phone is low power during live, it can be recharged directly through the Type-C or Lightning port on the RX receiver.
    ※ Some models do not support this function.

MOMAN CP2 1-Trigger-2 Wireless Phone Microphone - Charging Case
2

Charging Case
Charging
Connect the case with power supply via the charging cable.
※ When two transmitters are put in the charging case again, the green lights are ON, displaying the remaining battery.

Specifications

TX

Transmission Frequency 2.4GHz
Transmission Distance ≥ 10m
Latency ≤ 20ms
Sensitivity – 38dB±3dB
Frequency Response 201-12-20KHz
Sampling Rate 48KHz
SNR ≥ 75dB
Battery 200mA
Working Time 15H
Charging Time 1.5H
 Working Current ≤ 512mA
Dimensions 42.3×32.5mm

Rx

Transmission Frequency  2.4GHz
Frequency Response 20Hz-20KHz
Dimensions 36x13mm

Charging Case

Charging Time  3H
 Battery  1000mA
Battery Life Provide 2 full charges
 Adapter 5V/1A
 Input Voltage 4.8-5.5V
Max. Current 500mA
Charging Port Type-C
Dimensions 106x65x33.5mm

Moman (UK) Limited
Unit 25 Basepoint Business Centre, Aviation Park, West Christchurch, United Kingdom BH23 6NX
www.momanx.com
@ Moman Global
https://moman.co/youtube

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals