Porta HDA783Y Wall Mounted Bath Shower Mixer User Manual

User Manual

HDA783Y Wall Mounted Bath Shower Mixer

GENERAL GUIDELINES FOR TAP INSTALLATION AND CARE INSTRUCTIONS
Before commencing to install the taps & shower please read all of the following instructions carefully failure to observe these guidelines could invalidate the warranty on the product.
It is important for optimum performance of the tap that the hot and cold water supplies are balanced.
Local water authority regulations require that isolating valves are fitted in the pipe work beneath the tap to allow the tap to be individually isolated. This makes servicing or replacement of the tap much easier.
Any warranty claim on the tap will be handled on the basis that isolating valves have been fitted
Bath panels MUST be installed so that they can be removed to allow servicing /replacement of the tap and must NOT be tiled in. The panel must be installed AFTER all tiling has been completed.
Basin wastes should be installed with a bead of silicone to ensure a watertight seal and the rubber washer fitted before the nut. Do NOT over tighten the nut this could damage the basin and invalidate the warranty.
Basin wastes may be supplied with rubber washer(s) and it is recommended that where washer(s) are supplied a small bead of silicone is also applied to both sides of the bath before the nut is fitted and tightened. Do NOT over tighten the nut as this could damage the bath and invalidate the warranty.
Where flexi tails are supplied t is essential that they are NOT over tightened.
Once the tap has been installed the water supply should be turned on and the whole installation thoroughly checked for leaks. It is ESSENTIAL that the system is thoroughly flushed to remove any debris or foreign matter which could become lodged under the valve seat and cause dripping or premature failure.
It is important that tile grout or any aggressive cleaners do not come into contact with the tap and cleaning should be with warm soapy water and the tap thoroughly dried after cleaning.
Do not exceed the recommended maximum BAR pressure

Wall Mounted Bath Shower Mixer

Installation and Maintenance Instructions
FITIING YOUR NEW MIXER
Fitting your new mixer is easy when you follow these simple step-by-step instructions.

1. Identify all components.
2. IMPORTANT! Rinse out pipework prior to fitting.
3. After having rinsed the pipework, install the valve as a standard exposed fitting, with the hose outlet facing downwards.
4. When connecting the water supply to the valve. t is recommended that the hot supply is to the left and the cold supply to the right with the hose outlet from the batten.
5. Connect the eccentric threaded wall unions to the supply pipes.
6. Ensure that the wall coverings are fitted to the mixer prior to the connection to the water supply.
7. Set the eccentric unions so they correspond with the valves inlets.
8. Fit the mixer to the unions, ensuring to lit the sealing with a spanner until watertight.
9. Turn on the water supply and check for leaks.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.
AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item. the surtaces will wear if cleaned incorrectly. Clean this product with a sort cloth and clean water.
The use of any abrasive material will invalidate the guarantee.

Wall Mounted Basin Mixer

Installation and Maintenance Instructions
FITTING YOUR NEW MIXER
Fitting your new mixer is easy when you follow these simple step-by-step instructions.

1. Identify all components.
2. Ensure that the wall cavity or duct is large enough to make all necessary connections. Check that min/max depth of cavity is measured from behind the finished surface of the wall.
3. Prior to installation flush out pipework to remove any debris.
4. Connect the water supply and outlet pipework lo the valve section and fully tighten fittings.
5. Connect the outlet pipework from the tap sections to the spout and fully tighten fittings.
6. Turn on waier supply and test for leaks.
7. If no leaks are found, finish wall plastering and tiling as required.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.
AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used ,n the manufacture of this item, the surtaces will wear if ceaned incorrectly. Clean this product with a sort cloth and clean water.
The use of any abrasive material will invalidate the guarantee.

Pillar Mounted Bath Shower Mixer & Bath Filler

Installation and Maintenance Instructions
REMOVING OLD TAPS OR MIXER

1. A “Tap Spanner” may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Be earful to save and inspect the fibre washer between the base of the tap tails and the water pipe.

FITIING YOUR NEW MIXER
Fitting your new mixer is easy when you follow these simple step-by-step instructions.

1. Identify all components.
2. Prior to installation flush out pipework to remove debris.
3. Place washers into connecting nuts at rear of body prior to assembly of pillars.
4. Screw pillars to body ensuring that each pillar is angled outwards (See Fig 1) from the connecting nut to give correct centres to fit on bath. Fully tighten nuts.
5. Place washers onto threaded section of pillars. Insert pillars through holes in bath.
6. From underside fit and tighten backnut until mixer is secure. Do not overtighten, otherwise you risk damage to bath.
7. Reconnect supply pipes checking that the sealing washers are in good condition (if not replace). Again do not overtighten. It is recommendedthat the hot water supply be connected to the eft hand fitting when installed.
8. Turn on water supply to refill system and check for leaks. If any leaks are noticed. check that the connections are adequately tightened. Once the connections are satisfactory, you can then connect your shower kit (if applicable)

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.
AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surtaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water.
The use of any abrasive material will invalidate the guarantee.

Mono Sink Mixer

Installation and Maintenance Instructions
REMOVING OLD TAPS OR MIXER

1. A spanner may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITIING YOUR NEW MIXER

1. Identify all components.
2. Prior to installation flush out pipework to remove debris.
3. Screw threaded bar into base of body
4. Place anti-rotational washer into groove at base of tap body threaded bar through the sink unit.
5. Slide rubber horseshoe washer and metal horseshoe washer over threaded bar and fix unit in place using stud nut. Do not overtighten as it could damage the basin.
6. Connect the copper pipes to the base of tap body and re-connect the hot and cold water supply taps.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where
AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used ,n the manufacture of this item, the surtaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water.
The use of any abrasive material will invalidate the guarantee.

Maintenance/ Care and Cleaning Instruction

Maintenance and Cleaning Instructions
The finishes of our products are durable. To keep our products in good condition, the end users are required to regularly maintain and clean all the surfaces based on the following guidelines:

• Warm water or mild soapy water should be used to remove system debris and limescale.
• After cleaning, all soapy water should be removed by water and polished with a clean, soft and dry cloth.
• No abrasive cleaning agents or materials should be used.
• No corrosive cleaning agents should be used, which will cause corrosion.
• More care should be taken in hard-water areas to ensure all the surfaces are regularly cleaned.
• Failure to do so will invalidate the product warranty.

Care Instructions
Please be careful when installing, using, cleaning and maintaining this product. Any defects or damages like peeling problem at this product due to the following reasons is not covered by the product warranty:

• incorrect installation.
• accidental or wilful misuse.
• inappropriate cleaning products.
• inadequate maintenance.
• chemical damage caused by system debris and build-up of limescale (any soapy water left on the surface of the product and not cleaned regular will affect the finish of the product.)
• physical damages like scratches.
• damage caused during repair work.
• water quality i.e. rusting water from the pipework need to be fully flushed out after use or water pressure issues.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>