PORTA PHONE ULP16-MSW Single Speaker with Switch Button User Manual
- June 14, 2024
- PORTA PHONE
Table of Contents
PORTA PHONE ULP16-MSW Single Speaker with Switch Button
Product Information
Specifications
- Model No.: ULP16-MSW (Single speaker with Switch button)
- Conference Mode: Supports separating headsets into 2 groups or all in conference mode
- Mic Muted: The microphone automatically stops when the Mic boom swivels up
Product Usage Instructions
Conference Mode
To use the conference mode, follow these steps:
- Locate the switch button on the lower side of the ear cup.
- Press the switch button to separate the 15 headsets into 2 groups or to have all headsets in conference mode.
- If a remote headset has registered in 2 groups, it will be included in the conference mode.
Mic Muted
The microphone automatically stops when the Mic boom swivels up.
To mute the microphone, follow these steps:
- Swivel up the Mic boom to stop the microphone.
- To unmute the microphone, swivel down the Mic boom.
Frequently Asked Questions (FAQ)
-
Q: What does FCC Warning mean?
A: FCC Warning means that this device complies with part 15 of the FCC Rules. It indicates that the device will not cause harmful interference and must accept any interference received, including interference that may cause undesired operation. -
Q: How can I prevent possible hearing damage?
A: To prevent possible hearing damage, avoid listening at high volume levels for long periods. It is recommended to take breaks and lower the volume when necessary.
Power ON/OFF
- Power ON: Press and hold the power button till to GREEN LED blinks or lights up.
- Power OFF: Press and hold the power button till to the RED LED flashes.
Pairing (Register mode)
- Press and hold the power button to turn the headset power ON, the power LED should blink in Green color.
- Enter the pairing mode: Press the volume down button 3 times continually, then press and hold the volume up till to the RED and Green LED blink alternately.
- The main headset enters the pairing mode first then also the Remote to pairing mode.
- The Green LED of the Remote headset will blink quickly and then turn off after being paired, press the power button to quit the pairing mode and keep the Main headset on the pairing mode can pair with more Remote or press the power button to quit pairing modes.
- Repeat the above step “d” for more Remote headsets paired with the same Main headset, or press the power button to finish the pairing(register).
- Press SW of the Main headset can make a total of 15 Remote headsets register in 2 separate groups. The Main headset can accept a maximum of 15 remotes registered in full duplex, the power LED will flash in an ORANGE color when the register remote reaches 15., press the power button to quit the pairing mode)
- Press the Switch button, and you can change from ”Main” mode to ”Remote” mode when enter the ”Remote” mode, can only pair to the particular Main headset
Talking and listening
- The main headset and remote headset will start to search each other after powering ON, the GREEN LED flashes 1 time every 3 seconds. The headset will be linked together automatically when the pairing ID is confirmed by the main headset and the LED turns ON in GREEN color.
- Press the volume up and down button to adjust the headset speaker sound volume.
CONFERENCE on MAIN
Press the switch located lower side of the ear cup to make 15 headsets to separate 2 groups or all in CONFERENCE if the remote headset has registered in 2 groups.
Mic Muted
The headset Microphone stopped automatically when the Mic boom swiveled up.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Warning:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
The device has been tested and complies with FCC/ISEDC SAR limits. To prevent possible hearing damage, do not listen at high volume levels for long periods.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>