RUST-OLEUM SRT-09 Stops Rust Textured Sprays User Manual
- June 3, 2024
- Rust-Oleum
Table of Contents
RUST-OLEUM SRT-09 Stops Rust Textured Sprays
DESCRIPTION AND USES
Rust-Oleum® Stops Rust® Textured Sprays are designed to provide a durable protective coating with excellent resistance to rust, and excellent resistance to abrasion, fading, chipping, and dulling. These sprays apply easily, provide excellent coverage and dry fast to a tough attractive finish. Rust-Oleum Stops Rust Textured Sprays are ideal for outdoor metal surfaces. These sprays feature a comfort tip with a wider finger pad to reduce fatigue caused by continuous spraying. Not for use on galvanized metal.
PRODUCTS
SKU DESCRIPTION (Aerosol)
MULTICOLOR TEXTURE
- 223523 Autumn Brown
- 223524 Desert Bisque
- 223525 Aged Iron
- 223526 Deep Forest
- 239119 Sea Green
- 239120 Radiant Brass
- 239121 Caribbean Sand
- 239122 Rustic Umber
TEXTURED METALLIC
- 251053 Silver
- 252303 Galaxy
- 252304 Moonlit Copper
- 262660 Mystic Brown
- 353030 Midnight Gold
TEXTURED
- 7220830 Black
- 7221830 Dark Pewter
- 7222830 Forest Green
- 7223830 Sandstone
- 7225830 White
- 7226830 Bronze
- 241255 Dark Brown
PRODUCT APPLICATION
Use outdoors or in a well-ventilated area such as an open garage. Use when temperature is between 50-90°F (10-32°C) and humidity is below 70% to ensure proper drying. Do not apply to surfaces that, when heated, exceed 200°F (93°C) or galvanized metal. Avoid spraying in very windy, dusty conditions. Cover surrounding area to protect from spray mist.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants by washing the
surface with a commercial detergent, or other suitable cleaning method. Rinse
with fresh water and allow to thoroughly dry. Remove loose paint and rust with
a wire brush or sandpaper. Previously coated surfaces must be sound and in
good condition. Smooth, hard, or glossy finishes should be scarified by
sanding to create a surface profile.
WARNING! If you scrape, sand or remove old paint from any surface, you
may release lead paint dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by contacting the
National Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRIMING
Use of a Stops Rust® Primer provides added corrosion protection, superior adhesion and hiding and is especially recommended for bare wood and metal.
- 7769830 Rusty Metal Primer
- 7780830 Clean Metal Primer
APPLICATION
Shake can vigorously for one minute after mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use. Hold can upright 18-24″ from surface and spray in a steady back- and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying. It is recommended to apply a light first coat, target 50% coverage. Apply 2 or more light coats a few minutes apart.
DRY AND RECOAT TIMES
Based on 70°F (21°C) 50% relative humidity. Allow more time at cooler temperatures. Dries to touch in 15 minutes, dry to handle in 1-2 hours, and fully dry in 48 hours. Primers may be top coated immediately. Apply a second coat or clear coat within 1 hour or after 48 hours.
CLEAN UP
Wipe off tip before storing. Clean up wet paint with Xylene or mineral spirits. Throw away empty can in trash pickup. Do not burn or place in home trash compactor.
CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other objects into the stem.
TECHNICAL DATA
PHYSICAL PROPERTIES
| TEXTURED SPRAYS
---|---
Resin Type| Solvent Acrylic
Pigment Type| Varies with color
MIR| Textured 0.80 Max Multicolor Texture1.05 Max Textured Metallic 1.25
Max
Fill Weight| 12 ounces
Solvents| Acetone, Toluene, Xylene
Recommended Dry Film Thickness (DFT) Per Coat| 1.0-2.0 mils (25-50µ)
Practical Coverage at Recommended DFT (assumes 15% material loss)| 4-8
sq. ft./can (0.37-0.74 m2/can)
Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity| Touch|
15 minutes
Handle| 1-2 hours
Recoat| Apply a second coat or clear coat within 1 hour or after 48
hours
Dry Heat Resistance| 200°F (93°C)
Shelf Life| 5 years
Flash Point| -156°F (-104°C)
Safety Information| For additional information, see SDS
Calculated values are shown and may vary from the actual manufactured material.
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation 11 Hawthorn Parkway Vernon Hills, Illinois 60061
Phone: 877∙385∙8155 www.rustoleum.com
Form: GDH-729
Rev.: 102021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>