RUST-OLEUM ROC-270 Platinum Truck Bed Coating Spray Paint User Manual

June 15, 2024
Rust-Oleum

RUST-OLEUM ROC-270 Platinum Truck Bed Coating Spray Paint

Product Information

Specifications

  • Product Name: ROC-270 Truck Bed Spray
  • SKU: 382630
  • Description: 15 Oz. Aerosol, Black
  • Resin Type: TRUCK BED PLATINUM Urethane
  • Pigment Types: Carbon Black Mixture of Aliphatic, Aromatic and Ketones
  • Solvents: MIR (27.89%), Weight Volume (15.92%)
  • Fill Weight: 15 Oz. (425g)
  • Recommended Dry Film Thickness (DFT) per Coat: 1 mil
  • Practical Coverage at Recommended DFT (assumes 15% material loss): Up to 30 sq. ft./15 Oz.
  • Touch Dry Time: Not specified
  • Handle Recoat Time: Not specified
  • Full Cure Time: Not specified
  • Flash Point: Not specified
  • Shelf Life: Not specified

Description and Uses
Rust-Oleum’s ROC-270 is a highly advanced and durable truck bed spray designed specifically for use on bare or primed metal truck beds. It provides excellent protection against rust and other environmental elements.

Product Usage Instructions

Surface Preparation

  1. Remove all rust, oil, and grease from the surfaces to be coated.
  2. Ensure that the surface is clean and dry.
  3. Mask off the surrounding area to avoid overspray on the auto finish.

Product Application

  1. Read all directions and safety instructions before beginning the project.
  2. Shake the can vigorously for at least one minute before use.
  3. Hold the can approximately 8-12 inches away from the surface to be coated.
  4. Apply the spray evenly in smooth, overlapping strokes.
  5. For best results, apply multiple thin coats rather than a single heavy coat.

Dry and Recoat Times
The dry and recoat times for ROC-270 Truck Bed Spray are not specified in the user manual. It is recommended to allow sufficient drying time between coats as per your project requirements.

Cleanup

  • When finished spraying, wipe off the tip before storing.
  • Clean up wet or dry coating with Xylol.
  • Mineral spirits can also be used to remove wet paint.
  • Throw away the empty can in trash pickup. Do not burn or place it in a home trash compactor.

Clogging
If the valve clogs, twist and pull off the spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other object into the stem.

FAQ (Frequently Asked Questions)

  • Q: Can ROC-270 Truck Bed Spray be used on surfaces other than bare or primed metal truck beds?
    A: No, this product is specifically formulated for use on bare or primed metal truck beds. Using it on other surfaces may result in poor adhesion and performance.

  • Q: How long does it take for ROC-270 Truck Bed Spray to dry?
    A: The user manual does not specify the exact drying time. It is recommended to allow sufficient drying time between coats and follow the manufacturer’s instructions for the specific project requirements.

  • Q: Can ROC-270 Truck Bed Spray be used on a wet surface?
    A: No, the surface must be clean and dry before applying the spray. Applying it on a wet surface may affect adhesion and result in an uneven finish.

  • Q: What should I do if the spray nozzle clogs?
    A: If the valve clogs, twist and pull off the spray tip, and rinse it in a solvent such as mineral spirits. Avoid using pins or other objects to unclog the stem as it may damage the nozzle.

DESCRIPTION AND USES

Rust-Oleum® Platinum Series Truck Bed Coating is built for truck owners who demand long-lasting protection from scratches, impacts, corrosion, and fading.
Rust-Oleum’s most advanced and durable truck bed spray contains:

  • Specialized Polyurethane technology to provide 5X tougher impact resistance compared to Rust-Oleum’s standard truck bed spray
  • Stops Rust® formula offers superior protection from rust and corrosion
  • High-Output Spray System delivers premium spray experience for even coats and no-drip coverage

For use on: Bare or primed metal truck beds.

PRODUCT

PRODUCT APPLICATION

READ ALL DIRECTIONS BEFORE BEGINNING PROJECT

SURFACE PREPARATION
Remove all rust, oil and grease from surfaces to be coated. Surface must be clean and dry. Mask off area to avoid overspray on auto finish. Apply to bare or primed metal surface.
WARNING: If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800-424-LEAD or log on to www.eps.gov/lead.

APPLICATION
Use outdoors or in a well-ventilated area such as an open garage. Use when temperature is above 50°F (10°C) and humidity is below 65% to ensure proper drying. Avoid spraying in very windy, dusty conditions. Cover nearby objects to protect from overspray.
Shake can vigorously for one minute after mixing ball begins to rattle. If the mixing ball fails to rattle DO NOT STRIKE. Contact Rust-Oleum. Shake often during use. Hold can upright 12-18” from surface and spray in a steady back- and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface and in motion while spraying. Remove any overspray from the auto finish immediately. For the best results, apply two coats (allow product to dry for 1-2 minutes between coats).

DRY AND RECOAT TIMES
Air dry for a minimum of one hour at 70°F (21°C) – 50% relative humidity. Allow more time at cooler temperatures. Surface can be recoated within 1 hour or after 24 hours. Allow 72 hours for full cure before placing items in the truck bed.

CLEANUP
When finished spraying, wipe off tip before storing. Clean up wet or dry coating with Xylol. Mineral spirits can also be used to remove wet paint. Throw away empty can in trash pickup. Do not burn or place in home trash compactor.

CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other object into the stem.

PHYSICAL PROPERTIES

  TRUCK BED PLATINUM
Resin Type Urethane
Pigment Types Carbon Black
Solvents Mixture of Aliphatic, Aromatic and Ketones
Solids Weight
Volume 15.92%
Fill Weight 15 Oz. (425g)
MIR 0.80 Max
Recommended Dry Film Thickness (DFT) per Coat 1 mil per coat
Practical Coverage at Recommended DFT (assumes 15% material loss) Up to

30 sq. ft./15 Oz.
Dry Times at 77°F (25°C) and 50% Relative Humidity| Touch| 1 hour
Handle| 2 hours
Recoat| Before 1 hour and after 24 hours
Full Cure| 7 days
Flash Point| 141°F
Shelf Life| 5 years.
Safety Information| For additional information, see SDS

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice.

Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 800∙481∙4785
www.rustoleum.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Rust-Oleum User Manuals

Related Manuals