RUST-OLEUM ROC-98 Roof and Construction Sealant User Guide
- June 4, 2024
- Rust-Oleum
Table of Contents
RUST-OLEUM ROC-98 Roof and Construction Sealant User Guide
DESCRIPTION AND USES
Rust-Oleum® Roof and Construction Sealant is a high performance elastomeric sealant designed for sealing roofs, walls, trim, doors and windows. It is ideal for residential and commercial applications. This water-based sealant remains flexible and can be painted.
PRODUCT FEATURES
- Highly flexible for superior durability
- Patches seams & splits and seals roof fasteners
- Easy water clean up
- 10 Year warranty
- Use for vinyl, wood, masonry and most roofing surfaces
PRODUCT
| SKU | DESCRIPTION |
|---|---|
| 301827 | 10.1 Ounce Cartridge |
PRODUCT APPLICATION
SURFACE PREPARATION
All surfaces must be clean, dry, sound and free from dirt, grease, oil, mold, algae, loose granules, loose gravel, loose paint, rust, excess chalk and other foreign matter which could prevent proper adhesion. Wire brush all rusted metal and prime with Rust-Oleum Universal Roof Primer.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-Approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800- 424-LEAD or log on to www.epa.gov/lead.
APPLICATION
For exterior use only.
Apply only when air, material, and surface temperatures are between 40-100ºF (4-38ºC) and the relative humidity is below 85%.
Place cartridge in a cradle type caulking gun. Cut tip and puncture seal in spout. Squeeze trigger slowly. Apply ¼-½” bead of sealant to areas that are to be sealed. Use backer rod for deep joints.
COVERAGE
Will cover approximately 25 linear feet. Actual coverage will vary depending upon application method.
DRY & RECOAT TIMES
Dry and recoat times are based on 70ºF and 50% relative humidity. Allow to dry
at least 4-8 hours for thorough dry.
Product will reach full cure in 24 hours. Environmental or site specific
conditions may lead to a variation in dry time.
CLEAN-UP
Clean up wet product with water. Wash tools and equipment with soap and water. Properly dispose of all soiled rags and containers.
LIMITATIONS
Do not store above 90ºF (32ºC). DO NOT apply if rain is expected within 48 hours of application.
PROTECT FROM FREEZING
PHYSICAL PROPERTIES
| ROOF AND CONSTRUCTION SEALANT
---|---
Resin Type| Elastomeric Acrylic
Pigment Type| Titanium Dioxide, Mineral
Solvents| Water
Weight| Per Gallon| 11.5 lbs.
Per Liter| 1.38 kg
Solids| By Weight| 69%
By Volume| 55%
VOC| <25 g/l
Practical Coverage| Approximately 25 linear feet depending on ambient
temperature and surface conditions
Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity| Through
Dry| 4-8 hours
Full Cure| 24 hours
Shelf Life| 3 years
Flash Point| 200ºF (93ºC)
Safety Information| For additional information, see SDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 844∙888∙0485
www.rustoleum.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>