RUST-OLEUM ROC-222 Wheel Paint Instruction Manual

June 15, 2024
Rust-Oleum

TECHNICAL DATA
ROC-222
RUST-OLEUM®
WHEEL PAINT

DESCRIPTION AND USES

Rust-Oleum® Wheel Paint enhances the look and color of your vehicle’s wheels while keeping the surface free from rust. This fade resistant formula provides ultimate durability and performance on metal surfaces. Recommended for use on hubcaps and wheels  made of aluminum or steel.

PRODUCT FEATURES

  • Fade resistant
  • No peel promise
  • Adhesion guarantee

PRODUCTS

SKU DESCRIPTION (Aerosol)
368076 Wheel Gloss Black
266439 Wheel Gloss Clear
368077 Wheel Metallic Gold
366441 Wheel Metallic Graphite
366440 Wheel Metallic Steel
366438 Wheel Matte Black

PRODUCT APPLICATION

READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING PROJECT

SURFACE PREPARATION
Remove loose paint and rust with a wire brush or sandpaper.
Lightly sand smooth and glossy surfaces. Wipe the surface clean with Rust- Oleum Wax & Tar Remover and then let dry.

APPLICATION
Shake can vigorously for one minute after mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN.
Contact Rust-Oleum. Shake often during use. Hold can 10-16″ from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying. For best  appearance, apply one light coat followed by one heavier coat.

NOTE: Rust-Oleum Wheel Paint features an advanced spray system that allows you to spray at any angle, even upside down for those hard to reach areas. A comfort spray tip with wider finger pad reduces fatigue caused by continuous spraying.

DRY & RECOAT TIMES
Based on 70°F and 50% relative humidity. Dries to touch in 10 minutes and is fully dry in 30 minutes. Allow more time at cooler temperatures. Apply an additional coat at any time.
For an even glossier finish, top coat with Rust-Oleum Wheel Clear after 10 minutes.

CLEAN-UP
Wipe off tip when finished. Clean up wet paint with Xylol or Acetone. Throw away empty can in trash pickup. Do not burn or place in home trash compactor.

CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a solvent such as Acetone. Do not stick a pin or other objects into the stem.

PHYSICAL PROPERTIES

| WHEEL PAINT
---|---
Resin| Acrylic
Pigment| Varies with color
Solvents| Ketones, Dimethyl Carbonate
MIR| 0.95 max
Fill Weight| 11 oz.
Recommended Dry Film Thickness (OFT) Per Coat| 1.5-2.5 mils
Dry Times @ 77°F (25°C) and 50% Relative Humidity| Touch| 10 minutes
Handle| 30 minutes
Recoat| Anytime
Shelf Life| 5 years
Dry Heat Resistance| 200°F
Flash Point| -156°F
Safety Information| For additional information, see SDS

Calculated values are shown and may vary from the actual manufactured material.

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As  conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change  without notice.

Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
Phone: 866∙585∙8430
www.rustoleum.com/automotive
Form: ARJ-2241
Rev.: 062723

Documents / Resources

| RUST-OLEUM ROC-222 Wheel Paint [pdf] Instruction Manual
ROC-222 Wheel Paint, ROC-222, Wheel Paint, Paint
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Rust-Oleum User Manuals

Related Manuals