StarTech Com DKT31CH2CPD3 USB C Multiport Adapter 4K 60Hz HDMI PD User Guide
- June 4, 2024
- StarTech com
Table of Contents
StarTech Com DKT31CH2CPD3 USB C Multiport Adapter 4K 60Hz HDMI PD User Guide
Product ID
DKT31CH2CPD3
Product Diagram (Side A)
Requirements
• Computer
• DP Alt Mode enabled USB-C Port
For the latest drivers, manuals, product information, technical
specifications, and declarations of conformance, please visit:
www.StarTech.com/DKT31CH2CPD3
Package Contents
- USB-C MultiPort Adapter x 1
- Quick-Start Guide x 1
Installation
Side A Ports
-
Connect the Built-in USB-C Host Cable , located on the Multiport Adapter, to a USB-C Port on your Host Computer. Your Host Computer will automatically detect the device and install the required drivers.
-
Connect an HDMI Enabled Display to the HDMI Output Port, located on the MultiPort Adapter, using an HDMI cable.
Notes:
• The computer’s USB-C port must support DP Alt Mode to output video.
• Video performance, such as resolution, and refresh rate depends upon the connected Host Computer’s video controller. Please verify the specifications of the Host Computer. -
Connect USB Peripheral Devices to the USB-A Data/Charge Port , located on the Multiport Adapter.
Notes:
• Power and charge the connected Peripheral Devices with up to 5 V/1.5 A (7.5 W).
• A USB-C Power Adapter must be connected to the USB-C 100 W Power Delivery Port , located on the Multiport Adapter, to charge Peripheral Devices.
• Without a power adapter connected, the USB port will output whatever bus power is available, up to 4.5W. -
Connect a USB Peripheral Device to the USB-C Data/Charge Port, located on the Multiport Adapter.
Notes:
• Power and charge the connected Peripheral Device with up to 5 V/3 A (15 W).
• A USB-C Power Adapter must be connected to the USB-C 100 W Power Delivery Port, located on the Multiport Adapter, to charge Peripheral Devices.
• Without a Power Adapter connected, the USB-C DATA/Charge Port will output whatever bus power is available, up to 4.5 W.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a 3-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Regulatory Compliance
FCC — Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by
StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada. CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp