Startech com RK119WALLV2 1U 19 Inch Wall Mount Vertical Rack Bracket User Manual

Startech com RK119WALLV2 1U 19 Inch Wall Mount Vertical Rack Bracket

Product Information

The Quick-Start Guide provides instructions for the assembly and usage of the 1U 19in Vertical Wall Mount Rack Bracket. The product diagram for RK119WALLV2 is also included in the guide. The product is designed to mount equipment vertically on a wall or mounting structure.

Warnings

• Read the entire Quick-Start Guide and ensure the instructions are fully understood before assembling and/or using this product.
• Before adding equipment to this product, ensure it has been properly mounted.
• Never operate this product if parts are missing or damaged.
• The mounting hardware included with this product might not be adequate for some wall or mounting structures. If lacking the necessary expertise to mount this product, contact a construction professional to install the Wall Rack Bracket or to provide specific mounting instructions for the wall structure.
• Ensure the weight of the equipment does not exceed the weight capacity of this product. If the weight capacity is exceeded, personal injury or damage to the equipment are possibilities. This product can support the following weight: 130 lb (59 kg) for RK119WALLV2.

Component 1: Mounting Rails
The Mounting Rails are used to secure equipment in place on the Wall Mount Rack Bracket. The spacing between the mounting holes is 16 inches (2 inner holes) and 18.8 inches (4 outer holes) apart. The product may vary from the image provided.

Function
The Wall Mount Rack Bracket should only be mounted on a wall or mounting structure that is capable of supporting at least four times the weight of the mounted equipment. Failure to do so might result in personal injury and/or equipment damage.

Product Usage Instruction

Mount the Rack Bracket

1. Mark the Mounting Points (x6) using the Mounting Holes (x6) on\ the Wall Bracket as a Template.
2. Use the Wood Screws (x6) to fasten the Wall Bracket to the Mounting Surface. The included screws are for wood surfaces only.
3. Install the M5 Square Cage Nuts onto the desired Square Cage Nut Holes using the Nut Tool if available or your preferred tool.
4. Use a Phillips Head Screwdriver to install the M5 Screws and secure the Equipment onto the Mounting Rails.

Requirements
The product requires a mounting surface capable of supporting at least four times the weight of the mounted equipment. The M5 Square Cage Nuts and Screws are required to secure equipment onto the Mounting Rails.

Regulatory Compliance
The product complies with regulatory standards for safe usage. For further information on regulatory compliance, please visit www.startech.com/RK119WALLV2.

Warranty Information
The product is backed by a lifetime warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
StarTech.com Ltd. is not liable for any personal injury or damage to equipment resulting from improper use or installation of this product.

Contact Information

• StarTech.com Ltd., 45 Artisans Crescent, London, Ontario N5V 5E9 Canada
• StarTech.com LLP, 4490 South Hamilton Road, Groveport, Ohio 43125 U.S.A.
• StarTech.com Ltd., Unit B, Pinnacle 15 Gowerton Road, Brackmills, Northampton NN4 7BW United Kingdom
• StarTech.com Ltd., Siriusdreef 17-27, 2132 WT Hoofddorp, The Netherlands

Product Diagram

Product Diagram (RK119WALLV2)

Fasten it to a Wall

Package Contents

• Wall-Mount Bracket x 1
• Wood Screws x 6
• M5 Square Cage Nuts x 4
• M5 Screws x 4
• Quick-Start Guide x 1

Requirements

For the latest manuals, product information, technical specifications, and declarations of conformance, please visit: www.startech.com/RK119WALLV2.

• Appropriate mounting hardware for the wall or surface type
• Phillips head screwdriver
• Cage nut tool (Optional)

Warnings!
Read the entire Quick-Start Guide and ensure the instructions are fully understood before assembling and/or using this product. Before adding equipment to this product, ensure this product has been properly mounted.

Never operate this product if parts are missing or damaged. The mounting hardware included with this product might not be adequate for some wall or mounting structures. If lacking the necessary expertise to mount this product, contact a construction professional to install the Wall Rack Bracket or to provide specific mounting instructions for the wall structure. Ensure the weight of the equipment does not exceed the weight capacity of this product. If the weight capacity is exceeded, personal injury or damage to the equipment are possibilities. This product can support the following weight: 130 lb (59 kg) for RK119WALLV2.

Ensure the type of wall structure and mounting hardware will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall or mounting structure should be capable of supporting at least four times the weight of the mounted equipment.

Installation

Mount the Rack Bracket
The mounting holes are spaced 16 inches (2 inner holes) and 18.8 inches (4 outer holes) apart. Test fit the Rack Bracket on the surface to ensure proper fit on the designated location.

1. Mark the Mounting Points (x6) using the Mounting Holes (x6) on the Wall Bracket as a Template.
2. Use the Wood Screws (x6) to fasten the Wall Bracket to the Mounting Surface. The included screws are for wood surfaces only.
3. Install the M5 Square Cage Nuts onto the desired Square Cage Nut Holes where the Equipment will go. Use a Cage Nut Tool if available or your preferred installation method.
4. Use a Phillips Head Screwdriver to install the M5 Screws and secure the Equipment onto the Mounting Rails.

Regulatory Compliance

Use of Trademarks, Registered Trademarks, and Other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders. PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a lifetime warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Contact Information

• StarTech.com Ltd.
  45 Artisans Crescent London, Ontario N5V 5E9 Canada

• StarTech.com LLP
  4490 South Hamilton Road Groveport, Ohio 43125 U.S.A.

• StarTech.com Ltd.
  Unit B, Pinnacle 15 Gowerton Road Brackmills, Northampton NN4 7BW United Kingdom

• StarTech.com Ltd.
  Siriusdreef 17-27 2132 WT Hoofddorp The Netherlands

• FR: startech.com/fr

• DE: startech.com/de

• ES: startech.com/es

• NL: startech.com/nl

• IT: startech.com/it

• JP: startech.com/jp.

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

References

• Unsere Produkte dienen IT- und A/V-Profis zum Verbinden, Konvertieren, Erweitern, Splitten und Switchen | Deutschland
• StarTech.com diseña y fabrica una variada gama de componentes para ordenadores, cables, conmutadores KVM, racks para... | España
• StarTech.com conçoit et fabrique une vaste sélection de pièces d’ordinateur, de câbles, de commutateur KVM, de racks... | France
• Pezzi per computer, cavi, switch KVM, server rack e soluzioni per reti | Italia
• 当社は、接続、変換、拡張、分離、切換えを行うIT & A / Vプロフェッショナルのためのパーツを製造しています | 日本
• StarTech.com ontwerpt en produceert een enorme selectie computeronderdelen, kabels, KVM-switches, serverracks en... | Nederland
• 1U 19' Wall Mount Vertical Rack Bracket - Server-Racks | StarTech.com
• StarTech.com Support
• StarTech.com Warranty Policy

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>