StarTech com DKM31C3HVCPD USB-C 10Gbps Docking Triple Monitor Mini Station User Guide

: October 30, 2023
: StarTech com

Table of Contents

Product ID
Product Diagram (Side A)
Requirements
Installation
Use of Trademarks
Warranty Information
Limitation of Liability
Regulatory Compliance
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

StarTech com DKM31C3HVCPD USB-C 10Gbps Docking Triple Monitor Mini Station

StarTech com DKM31C3HVCPD USB-C 10Gbps Docking Triple Monitor Mini
Station

Product ID

DKM31C3HVCPD

Product Diagram (Side A)

$Product Diagram $Side A$$

Requirements

For the latest requirements, please visit www.StarTech.com/DKM31C3HVCPD

Component	Function

1

| Built-in USB-C Host Cable|

Connect to a USB-C Port on a Host Laptop
USB 3.2 Gen 2 (10Gbps)
Power Delivery 3.0 Specification

2

| VGA Video Port|

Connect a VGA Display Device
Up to 1080p (1920×1200/1920×1080) 60Hz
Via DisplayPort 1.4 DP Alt Mode

3

| HDMI Video Port|

Connect an HDMI Display Device
HDMI 2.0b HDR10
Up to 4K (4096×2160) 60Hz
Via DisplayPort 1.4 DP Alt Mode

4

| USB-C Data/Charge/DP++ Video Port|

Connect and/or charge a USB-C peripheral
Connect a USB-C display directly, or for any other Display, a USB-C Video Adapter is required
USB 3.2 Gen 2 (10Gbps)
Supports 5V/2A (10W) charging
Display output via DisplayPort 1.4 DP Alt Mode
USB-C Power Adapter required for charging

5

| 2x USB-A DataPorts|

Connect and/or charge USB-A peripherals
USB 3.2 Gen 2 (10Gbps)

6

| USB-C 100W Power
Delivery Input Port|

Connect a USB-C power adapter
USB Power Delivery 3.0

7

| Gb Ethernet Port|

Connect a CAT 5e/CAT 6 cable to establish a network connection
10/100/1000Mbps

Installation

Side A Ports

Connect the Built-in USB-C Host Cable on the Multiport Adapter to a USB-C port on your host laptop. Your computer will automatically detect the device and install all the required drivers.
Connect a VGA cable from your VGA enabled display device to the VGA Output Port on the Multiport Adapter, to add a VGA display to your workstation.
Connect an HDMI cable from your HDMI enabled display device, to the HDMI Output Port on the Multiport Adapter, to add an HDMI display to your workstation.
To connect a display: If using display with USB-C input, connect a USB-C cable from your display to the USB-C DP++ Video Port on the Multiport Adapter . For other displays, connect a USB-C Video Adapter (HDMI, DisplayPort or VGA, sold separately) from the USB-C DP++ Video Port on the Multiport Adapter to your display device.

To connect and/or charge a USB-C peripheral device: Connect a USB-C cable from your USB peripheral device to the USB-C Data/Charge Port on the Multiport Adapter.

Notes:

A video cable may also be required to connect your display, depending upon your USB-C video adapter.
Your computer’s USB-C port must support DP Alt Mode in order to output video.
Video performance, such as resolution, refresh rate depends upon your host computer’s video controller. Please verify the specifications of your computer.
A USB-C power adapter must be connected to the USB-C 100W Power Delivery Input Port on the Multiport Adapter, in order to charge connected peripheral devices with up to 5V/2A (10W).
Without a power adapter connected, the USB port will output whatever bus power is available, up to 4.5W

Side B Port

5. Connect USB-A cables from your USB peripheral devices to the USB-A Data Ports on the Multiport Adapter, to connect the devices to your computer.

Notes:
• One of the USB-A Data Ports is located on Side C.
• The USB port will output whatever bus power is available, up to 4.5W.

Side C Port

6. Connect a USB-C power adapter (up to 100W) from an AC outlet to the USB-C 100W Power Delivery Input Port on the Multiport Adapter, to charge the laptop that’s connected to the Built-in USB-C Host Cable.

Side D Port

7. Connect a CAT 5e/CAT 6 cable from your local area network (e.g. Router, Switch,
Modem, etc.) to the Gb Ethernet Port on the Multiport Adapter, to access your
network via a wired LAN connection.

Use of Trademarks

Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a 3-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Regulatory Compliance

FCC – Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.