StarTech com 5G16AINDS-USB-A-HUB 16-Port Industrial USB 3.2 Gen 1 Hub User Guide

StarTech com 5G16AINDS-USB-A-HUB 16-Port Industrial USB 3.2 Gen 1 Hub

Product Information

The 16-Port Industrial USB 3.2 Gen 1 Hub with ESD and Surge Protection is a device used to connect up to 16 USB peripherals. It comes with 16 USB Data/Charge Ports (Screw Locking, USB-A), two USB Host Ports (Screw Locking, USB-B), and a DC Power Input. The USB Hub also includes DIN Rail Brackets that can be used to horizontally mount the USB Hub to a DIN Rail.

Product ID
5G16AINDS-USB-A-HUB

Package Contents

• 16-Port Industrial USB 3.2 Gen 1 Hub
• 2x USB-A to USB-B Cables
• 1U Mounting Brackets
• DC 2-Wire Terminal Block Power Input
• Quick-Start Guide

Requirements

The USB Hub requires an external DC Power Adapter or a Terminal Block Power Source with a voltage range of +12 – 24 V DC. Visit www.StarTech.com/5G16AINDS-USB-A-HUB for the latest drivers, manuals, product information, technical specifications, and declarations of conformance.

Product Usage Instructions

Installation
To install the USB Hub:

1. Connect up to 16 USB peripherals to the Screw Locking USB Data/Charge Ports located on the USB Hub.
2. Use the 2x USB-A to USB-B Cables to connect a USB port on each Computer to the USB Host A & B Ports located on the USB Hub.
3. Power the Hub using an external DC Power Adapter or a Terminal Block Power Source with a voltage range of +12 – 24 V DC.

Powering the Hub using Terminal Block Power Source
To power the Hub using the 2-Wire Terminal Block:

1. Remove the Terminal Block Connector Housing from the USB Hub’s Casing.
2. Loosen the screws for the Terminals located on the Terminal Block Connector, using a Flat Head Screwdriver.
3. Connect the Positive and Negative Wires from the 12-24V DC Power Source (not included) to the Terminals on the Terminal Block Connector.
4. Insert the Terminal Block Connector Housing back into USB Hub.

DIN Rail Mounting
To mount the USB Hub to a DIN Rail:

1. Align the Din Rail Brackets (x 2) with the DIN Rail Mounting Holes, located on either side at the back of the USB Hub.
2. Insert the Mounting Screws (x 4) through the DIN Rail Brackets, and into the USB Hub.
3. Using a Phillips Head Screwdriver tighten the Mounting Screws. Be careful not to over-tighten the Mounting Screws.

Trademark Usage
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols are subject to applicable trademark laws and regulations.

Warranty Information

The product comes with a 2-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
StarTech.com Ltd. is not liable for any loss, damage, or injury arising from the use of this product.

16-Port Industrial USB 3.2 Gen 1 Hub – ESD and Surge Protection – Dual Host

Product ID
5G16AINDS-USB-A-HUB

Product Diagram

Package Contents

• USB Hub x 1
• 10 ft [3 m] USB-A to USB-B Cable x 1
• Terminal Block Connector (Attached)
• DIN Rail Mounting Brackets (with Mounting Screws) x 2
• Quick-Start Guide x 1

Requirements

• Computer (1 or 2 units)
• USB-A Port
• 12-24V DC Power Source
  For the latest drivers, manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/5G16AINDS-USB-A-HUB

Installation

Notes:

• Connect the Power Source after all the other installation steps have been completed.
• There are two ways to power the USB Hub.
  Using an external DC Power Adapter or a Terminal Block Power Source. Voltage (+12 – 24 V DC).

Connect the USB Ports

1. Connect up to 16 USB peripherals to the Screw Locking USB Data/Charge Ports, located on the USB Hub.
2. Use the 2x USB-A to USB-B Cables (1x cable included, second sold separately), to connect a USB port on each Computer to the USB Host A & B Ports, located on the USB Hub.
   • The Computer will automatically detect the device and install the required drivers for the USB Hub.

Power the Hub
Power the Hub Using the 2-Wire Terminal Block

1. Remove the Terminal Block Connector Housing from the USB Hub’s Casing.
2. Loosen the screws for the Terminals located on the Terminal Block Connector, using a Flat Head Screwdriver.
3. Connect the Positive and Negative Wires from the 12-24V DC Power Source (not included) to the Terminals on the Terminal Block Connector

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Warranty Information
This product is backed by a 2-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you

Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire Terminal Block Pins to function properly and to prevent damage to the USB Hub and any connected peripherals

Insert the Terminal Block Connector Housing back into USB Hub.
Power the Hub Using an External Power Adapter

• Connect a Power Adapter (not included) to the Power Input Port, located on the front of the USB Hub and to an AC Electrical Outlet.

DIN Rail Mounting

This USB Hub includes DIN Rail Brackets that can be used to horizontally mount the USB Hub to a DIN Rail. To install the DIN Rail Brackets on the USB Hub:

1. Align the Din Rail Brackets (x 2) with the DIN Rail Mounting Holes, located on either side at the back of the USB Hub.
2. Insert the Mounting Screws (x 4) through the DIN Rail Brackets, and into the USB Hub.
3. Using a Phillips Head Screwdriver tighten the Mounting Screws. Be careful not to over-tighten the Mounting Screws

Regulatory Compliance

FCC – Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Rack Mount the USB Hub (5G16AINDS-USB-A-HUB)

This USB Hub includes Rack Mounting Brackets that can be used to mount the USB Hub into 1U of EIA-310 compliant 19” rack space.
The USB Hub features two sets of Rack Mounting Holes (front and rear), located on either side. This enables the USB Hub to be mounted to at either the front or rear, depending upon your preference.

To install the Rack Mounting Brackets on the USB Hub:

1. Remove the pre-installed Mounting Screws (x6) from the front or rear (depending upon your mounting preference) on both sides of the USB Hub (x3 Mounting Screws per side).
2. Align the Rack Mounting Brackets (x 2) with the Rack Mounting Holes, located on either side of the USB Hub.
3. Reinsert the Mounting Screws (x 6, removed in step 1) through the Rack Mounting Brackets, and into the USB Hub, on both sides, and tighten the Mounting Screwsusing a Phillips Head Screwdriver. Be careful not to over-tighten the Mounting Screws.

To install the USB Hub (with Rack Mounting Brackets attached) into 1U of EIA-310 compliant 19” rack space:

1. Locate a suitable location in the rack/cabinet to mount the USB Hub. The USB Hub itself requires 1U of space within the rack/cabinet.
2. If the Rack/Cabinet uses square mounting holes, install cage nuts into the square mounting holes on the front posts of the rack.
3. Place the USB Hub (with Rack Mounting Brackets attached) into the rack and align the mounting points on the front brackets of the USB Hub’s Mounting Brackets with the mounting points on the rack (e.g. the cage nuts, if used).
4. Use cabinet screws to secure the USB Hub to the rack. If not using cage nuts or M5/ M6 threaded rack posts, the appropriate mounting hardware for the rack should be used.
5. Make sure the screws are properly tightened and the USB Hub has no movement.

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada

StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.

StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom

StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands

References

• 16-Port Industrial USB 3.0 Hub/Switch - Industrial USB Hubs | StarTech.com
• StarTech.com Support
• StarTech.com Warranty Policy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>