AFTERSHOKZ OpenMove Wireless Headphones User Guide

AFTERSHOKZ OpenMove Wireless Headphones User Guide

Product Overview

How to Set Up OpenMove

1. Charge
   Charge the headphones with the included USB-C charging cable. The LED indicator will change from red to blue when charging is complete.

2. Pair
   Begin with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.

3. Connect
   Open your device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey will say “connected” and the LED indicator will flash blue one time.
   Let us take care of you! Protect your headphones against defects.
   Make sure to register your OpenMove at Aftershokz.com

Multifunction Button (A)

Play / pause music

| Click once| One beep
---|---|---
Skip to next song| Double-click

while music is playing

|

One beep

Skip to previous song| Triple-click

while music is playing

| One beep
Switch language| Double-click while on pairing|
Answer call| Click once| Two beeps
End call| Click once| One beep
Answer call waiting and hang up on current caller| Press and hold for 2 seconds| One beep
Reject a call| Press and hold for 2 seconds| Two beeps
Activate device’s voice assistant| Press and hold for 2 seconds| Device beep
Redial last number| Double-click (when idle)| “Redial last number”

Volume+ / Power Button (B); Volume- Button (C)

Power on| Press and hold volume+ for 2 seconds| “Welcome to AfterShokz”
---|---|---
Power off| Press and hold volume+ for 3 seconds| “Power off”
Mute| Press and hold both buttons for 2 seconds while on a call| “Mute on” or “Mute off”
Switch EQ| Press and hold both buttons for 3 seconds while music is playing| “Standard mode / Vocal booster mode / Earplug mode”
Check battery status| Click the volume+ or volume- button while music is paused| “Battery high/Battery medium/ Battery low/Charge me”
Adjust volume| Click the volume+ or volume- button to adjust volume while music is playing| One beep

Specifications

Model number
AS660

| Frequency response
20Hz – 20kHz
---|---
Speaker type Bone conduction transducer|

Speaker sensitivity
96 ± 3dB

Bluetooth® version

| Bluetooth® v5.0| Microphone sensitivity
-40 ± 2dB
---|---|---
Wireless range| 10 m|

Frequency band                2402 – 2480MHz

Battery     Rechargeable Li-Polymer battery

| Battery capacity                             135 mAh
Continuous play| Up to 6 hours|

Standby time                         Up to 10 days

Charge time

| 2 hours| Charge voltage                           5.25V ± 5%
Charge type| USB-C|

Speaker impedance                  8.0 ± 0.5ohm

Water resistance

| IP55| Maximum RF output power                 4dBm
Weight| 29 g|

Warranty                                          2 years

Compatible profiles

| HSP, HFP, A2DP AND AVRCP|
Solid red|

Charging

---|---

Solid blue

| Charging complete
Flashes red and blue|

Pairing mode

Flashes blue

| Incoming call
Flashes red every 2 minutes|

Low battery

Multipoint Pairing

1. Multipoint pairing allows OpenMove to be connected to two devices at once, allowing users to seamlessly transition between the two.
2. Begin with your headphones powered off.
3. Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
4. Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled”.
5. Open your first device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey says “connected”.
6. Turn your headphones off.
7. Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
8. Open your second device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey says “connected”.
9. Turn your headphones off.
10. Turn your headphones on. Your headphones are now connected to both devices. Audrey says “connected” and “device 2 connected”.
11. To turn off multipoint pairing: Press and hold the multifunction and volume – buttons for 3 seconds when pairing. Audrey says”multipoint disabled”.

More information: bit.ly/aftershokzpairing

How to Reset Your Headphones

1. Begin with your headphones powered off.
2. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
3. Press and hold the multifunction button, volume+ button and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
4. Turn your headphones off. OpenMove is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)
Use earplugs with headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

1. Roll earplugs firmly between fingers and place in ears.
2. To adjust EQ settings for earplugs, press and hold volume+ and volume- buttons simultaneously while music is playing. Continue through options until “earplug mode.”
3. Switch EQ to other settings when you take out the earplugs.

Manufacturer

AfterShokz LLC
3200 Gracie Kiltz Lane, 4th floor, Austin, TX 78758

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>