StarTech com RK119WALLV2 19 Inch Vertical Wall Mount Rack Bracket User Guide

: October 30, 2023
: StarTech com

Table of Contents

StarTech com RK119WALLV2 19 Inch Vertical Wall Mount Rack Bracket
Product Information
Product Usage Instructions
Product IDs
Product Diagram
Package Contents
Requirements
Installation
- Regulatory Compliance
Warranty Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

StarTech com RK119WALLV2 19 Inch Vertical Wall Mount Rack Bracket

StarTechcom-RK119WALLV2-19-InchVertical-Wall-Mount-Rack-Bracket-
PRODUCT

Product Information

The 19 Vertical Wall Mount Rack Bracket is a product designed to mount equipment on a vertical surface. It comes in six different product IDs, namely RK119WALLV2, RK219WALLV, RK319WALLV2, RK419WALLV2, RK519WALLV, and RK619WALLV. The product includes mounting rails, wall brackets, M5 square cage nuts, and M5 screws. It has a weight capacity ranging from 125.3 lb (56.7 kg) to 200.5 lb (90.7 kg) depending on the specific product ID.

Product Usage Instructions

Before installation, read the entire Quick-Start Guide and ensure that the instructions are fully understood.
Ensure that the product has been properly mounted before adding equipment to it. Use the included wood screws for wood surfaces only.
Install the M5 square cage nuts onto the desired square cage nut holes where the equipment will be installed. Use a cage nut tool if available or your preferred installation method.
Use a Phillips head screwdriver to install the M5 screws and secure the equipment onto the mounting rails.
Ensure that the weight of the equipment does not exceed the weight capacity of the specific product ID. If it does, personal injury or damage to the equipment are possibilities.
Ensure that the type of wall structure and mounting hardware will properly support the mounted equipment. The wall or mounting structure should be capable of supporting at least four times the weight of the mounted equipment.
If lacking the necessary expertise to mount this product, contact a construction professional to install the Wall Rack Bracket or to provide specific mounting instructions for the wall structure.

For more information on regulatory compliance and warranty, refer to the product manual available at www.startech.com/support.

Product IDs

RK119WALLV2
RK219WALLV
RK319WALLV2
RK419WALLV2
RK519WALLV
RK619WALLV

Product Diagram

Component	Function *Product may vary from image
1	Mounting Rails

mount the equipment
2| Wall Bracket| • Mounting Holes along the Wall Bracket are used to

Fasten it to a Wall

Package Contents

Wall-Mount Bracket x 1
Wood Screws x 6
Quick-Start Guide x 1

Product ID	M5 Square Cage Nuts Quantity	M5 Screws Quantity
RK119WALLV2	x 4	x 4
RK219WALLV	x 8	x 8
RK319WALLV2	x 12	x 12
RK419WALLV2	x 16	x 16
RK519WALLV	x 16	x 16
RK619WALLV	x 16	x 16

Requirements

For the latest manuals, product information, technical specifications, and declarations of conformance, please visit:
www.StarTech.com/RK119WALLV2
www.StarTech.com/RK219WALLV
www.StarTech.com/RK319WALLV2
www.StarTech.com/RK419WALLV2
www.StarTech.com/RK519WALLV
www.StarTech.com/RK619WALLV

Appropriate mounting hardware for the wall or surface type

Phillips head screwdriver
Cage nut tool (Optional)

Warnings!

Read the entire Quick-Start Guide and ensure the instructions are fully understood before assembling and/or using this product.
Before adding equipment to this product, ensure this product has been properly mounted.
Never operate this product if parts are missing or damaged.
The mounting hardware included with this product might not be adequate for some wall or mounting structures. If lacking the necessary expertise to mount this product, contact a construction professional to install the Wall Rack Bracket or to provide specific mounting instructions for the wall structure.
Ensure the weight of the equipment does not exceed the weight capacity of this product. If the weight capacity is exceeded, personal injury or damage to the equipment are possibilities. These products can support the following weight: 130 lb (59 kg) for RK119WALLV2, 125.3 lb (56.7 kg) for RK219WALLV, 150lb (68 kg) for RK319WALLV2, 180 lb (81.6 Kg) for RK419WALLV2, 198.9 lb (90 kg) for RK519WALLV, and 200.5 lb (90.7 kg) for RK619WALLV.
Ensure the type of wall structure and mounting hardware will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall or mounting structure should be capable of supporting at least four times the weight of the mounted equipment.

Installation

Mount the Rack Bracket

The mounting holes are spaced 16 inches (2 inner holes) and 18.8 inches (4 outer holes) apart. Test fit the Rack Bracket on the surface to ensure proper fit on the designated location.

Mark the Mounting Points (x6) using the Mounting Holes (x6) on the Wall Bracket as a Template.
Use the Wood Screws (x6) to fasten the Wall Bracket to the Mounting Surface.
- The included screws are for wood surfaces only.
Install the M5 Square Cage Nuts onto the desired Square Cage Nut Holes where the Equipment will be installed. Use a Cage Nut Tool if available or your preferred installation method.
Use a Phillips Head Screwdriver to install the M5 Screws and secure the Equipment onto the Mounting Rails.

Regulatory Compliance

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
ES:startech.com/es
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.