SATCO STARFISH In-Wall Wi-Fi Switch S11267 Instruction Manual
- June 6, 2024
- SATCO
Table of Contents
START HERE
In-Wall Wi-Fi Switch S11267
Installation Guide
WIFI
2.4GHz NO HUB NEEDED
ENJOY THESE OTHER GREAT STARFISH WIFI SMART LED PRODUCTS
| 
---|---
| 
Technical Support www.satco.com/Starfish
WARNING:
This product may represent a possible shock or fire hazard if improperly
installed or attached in any way. The product should be installed in
accordance with the owner’s
manual, current electrical codes, and/or the current National Electric Code
(NEC).
CAUTION: RISK OF ELECTRIC SHOCK.
-
TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING.
CAUTION: RISK OF FIRE. -
FOR CONTROL OF INCANDESCENT, CFL, LED, AND RESISTIVE LOADS AS WELL AS MOTORS
-
DO NOT USE WITH CONTROL RECEPTACLE OUTLETS, FLUORESCENT LIGHTING FIXTURES,
-
DO NOT EXCEED ELECTRICAL RATINGS. – USE INDOORS ONLY.
-
SHALL INSTALL IN A METALLIC OUTLET BOX HAVING MIN. WIDTH 50MM, OR A NON-METALLIC BOX.
-
ONLY USE WITH SOLID COPPER WIRE OR COPPER-CLAD WIRE.
CAUTION: -
INSTALLATION REQUIRES A NEUTRAL WIRE.
-
THIS DEVICE DOES NOT WORK WITH SMART LAMPS.
REPLACING LIGHT BULBS. -
Make sure switches are in OFF position (no light level indicator lights are lit)
-
To ensure there is no power at the socket when replacing light bulbs, turn off power at the circuit breaker or fuse.
FCC/IC INFORMATION
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
OPERATION
- Power Indicator &
Configuration Light - On/Off Switch
PARTS INCLUDED
| | | |
---|---|---|---|---
Wall plate (x1)| Mounting the frame (x1)| Smart Switch (x1)| Inner frame
screws (x2)| Mounting screws (pre-installed) (x2)
Verify that a neutral wire is available prior to installatio n
How do I know if I have a neutral wire?
- Turn the power off at your breaker box and ensure the power is off
- Remove the wall plate and existing device from the wall box
- Remove and straighten all wires from the device
- If you see a white wire (or bundle of them), it is likely that you have a neutral in that switch box
- If you do not have a neutral wire, this switch WILL NOT work If this looks different from your wall box, please consult a certified electrician
SWITCH INSTALLATION
Turn power OFF at the circuit breaker and ensure power is off.
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off power at circuit breaker or
fuse and test that power is off before wiring.
CONTINUED ON THE OTHER SIDE
Identify if your wiring is SINGLE POLE or 3-WAY
SINGLE POLE: control from a single location
WAY: control from 2 locations
You will need to determine which is the “LINE” wire and wall box and which is
the“LOAD” wire and wall box.
Your old switch may have a screw terminal of a different color (usually
black). This will either be the “LINE” connection or the “LOAD” connection.
Tag this wire with a piece of electrical tape.
Disconnect all wires from the old switch and ensure no wires are touching.
Turn the power back on at the circuit breaker. Use a handheld voltage tester
to determine if the tagged wire is “live”.
If the tagged wire is “live”, this is the “LINE” wire and wall box. If not,
this is the “LOAD” wire (and wall box in 3-way applications).
NOTE: Ensure power is off before performing this step!
Preparing and connecting wires: Use with #12-14 AWG solid copper or
copper-clad wire. Strip wires to 2 cm (.8 inch).
Insert wires into terminal holes and secure connections by tightening terminal screws to 16 lbs-in (1.8 N.M) as shown.
SINGLE POLE WIRING
Ensure that the following connections are made:
“LINE” wire to the terminal marked AC-L
“LOAD” wire to the terminal marked LOAD
Neutral wire to the terminal marked AC-N
Ground wire to the terminal marked GND
Note: A single-pole or The 3-way switch can be used alongside the smart
switch.
IMPORTANT: The switch must be installed in the “LINE” wall box and the
smart switch must be installed in the “LOAD” wall box.
Ensure that the following connections are made at the switch:
“LINE” wire to one terminal Traveler wire to the other terminal Ground wire to
the GND terminal
Ensure that the following connections are made at the smart switch:
“LINE” wire to the AC-L terminal
“LOAD” wire to the LOAD terminal
Traveler wire to the YL/RD terminal
Neutral wire to the AC-N terminal
Ground wire to the GND terminal
MOUNTING
Push wires into the wall box and push the switch into opening Mount the
switch into wall box and install the wall plate
TESTING
Turn the power back on at the circuit breaker Test the device to ensure that
the lights will turn on and off
https://smartapp.tuya.com/satcosmart
DOWNLOAD THE FREE “STARFISH SMART LIGHTING” APP
Please refer to our Starfish user guide for detailed instructions on how to
pair your device
TROUBLESHOOTING
Lights are flickering:
- The lamp has a bad connection.
- The switch wire connections are not firmly secured. Light does not turn ON:
- The circuit breaker or fuse has tripped.
- The bulb or lamp is burned out. The power indicator light does not turn ON:
- Neutral is not connected to switch (white wire)
- Confirm that switch is being supplied from a 120V AC,60Hz source ONLY. Intermittent switch operation:
- Confirm that the LOAD being controlled does not exceed 6A (720W) INC, CFL, LED, Resistive 3.6A Motor
This switch is rated for Incandescent, CFL, LED
and resistive loads as well as motors
120VAC 60HZ 6A (720W) INC, CFL, LED,
Resistive, 3.6A Motor
NOTE: A NEUTRAL WIRE IS REQUIRED FOR INSTALLATION
No Derating is required when installing in
multi-gang applications.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>