SATCO S18410 Lumos Light Bulb LED T8 U Bend Instruction Manual
- June 1, 2024
- SATCO
Table of Contents
SATCO S18410 Lumos Light Bulb LED T8 U Bend
Specifications
- Product Name: LED T8 DUAL MODE U-BEND LAMPS
- Models: S18410, S18411
- Overall Dimensions (mm): 92 x 562.1 x 572.3
- CCT Options: 30K, 35K, 40K, 50K
Installation Instructions
Direct Replacement / Plug & Play (Type A)
- STEP 1: Turn OFF power before installation.
- STEP 2: Remove the fixture diffuser (if present) and existing fluorescent lamps from the fixture.
- STEP 3: Install the LED U-bend.
- STEP 4: Attach the diffuser and turn the ON power. Installation is complete.
Bypassing Magnetic/Electronic Ballast (Type B)
- STEP 1: Turn OFF power before installation.
- STEP 2: Remove the existing ballast and existing starter (if present) from the fixture.
- STEP 3: Rewire the fixture to be single-end or double-end power as per the instructions provided.
- Single End Wiring: Leads 1 connected to L; Leads 2 connected to N; Leads 1 and 2 at the end of the lamp holder with LN.
- Double End Wiring: Leads 1 or 2 connected to L; Leads 3 or 4 connected to N.
- STEP 4: Install the LED U-bend.
- STEP 5: Turn the ON power. Installation is complete.
Frequently Asked Questions (FAQ)
Q: Is this product compatible with all ballasts?
A: This product may not be compatible with all ballasts. For more information about ballast compatibility, visit www.Satco.com.
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing the fixture. Retain for future reference.
WARNING
- DANGER: Risk of shock-disconnect power before installation.
- WARNING: Risk of fire or electric shock. The electrical rating of these products is 120-277Vac, the installer must determine whether they have 120-277Vac at the luminaire before installation.
- WARNING: Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- WARNING: The product must be installed per the national electrical code or your local electrical code.
- If you are not familiar with these codes and requirements, contact a qualified electrician.
- WARNING: Install this kit only in luminaries that have the construction features and dimensions shown in the photographs and/or drawing and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- WARNING: To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- WARNING: To avoid potential fire or shock hazards, do not use this retrofit kit in luminaries employing shunted bi-pin lamp holders.
- NOTE: Shunted lamp holders are found only in fluorescent luminaries with instant-start ballasts.
- Instant-start ballasts can be identified by the words “Instant Start” or “I.S.” marked on the ballast.
- This designation may be in the form of a statement of the ballast itself or may be combined with the marking for the lamps with which the ballasts are intended to be used, for example, F40T 12/IS, for more information contact the LED luminaire retrofit kit manufacturer. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. Installers should not disconnect the existing wire from lamp holder terminals to make new connections at lamp holder terminals. Instead, installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
- WARNING: Luminaire wiring and electrical parts may be damaged when installing retrofit kit hardware. Check for enclosed wiring and components.
- WARNING: Check the existing wiring for damage before installing the upgrade kit. Do not install if existing wires are damaged.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
- Type B Lamp – this LED tube is intended to replace fluorescent tube lamps with ANSI designation.
- This lamp is dimmable in Type A (Ballast Dependent) mode only. Dimmable ONLY with compatible dimmable ballasts.
- Visit www.satco.com for a compatibility list.
- Suitable for damp locations.
- Not for emergency lighting.
Item Number-Description| Overall Dimensions (mm)| Operating
Temperature| CCT| Volts
---|---|---|---|---
S18410 -13T8U6/LED/CCT/DUAL| 92 x 562.1 x 572.3| –20ºC ~ 45ºC| 30K, 35K,
40K, 50K
| 120V–277V
S18411 -13T8/U1/LED/CCT/DUAL
INSTALLATION: DIRECT REPLACEMENT / PLUG & PLAY (TYPE A)
NOTE: This product may not be compatible with all ballasts. For more information about ballast compatibility visit www.Satco.com.
- STEP 1: Turn OFF power before installation.
- STEP 2: Remove the fixture diffuser (if present) and existing fluorescent lamps from the fixture.
- STEP 3: Install the LED U-bend.
- STEP 4: Attach the diffuser and turn the ON power. Installation is complete.
INSTALLATION: BYPASSING MAGNETIC/ELECTRONIC BALLAST (TYPE B)
- STEP 1: Turn OFF power before installation.
- STEP 2: Remove the existing ballast and existing starter (if present) from the fixture.
Magnetic Ballast
The wiring can be single-end or double-end. The connection method refers to Step 3.
Electronic Ballast
STEP 3: Rewire the fixture to be one certain single-end/double-end power.
Single End
Single-end: Leads 1 connected to L; Leads 2 connected to N; Leads 1 and 2 at the end of the lampholder with LN.
Double End
Double-end: Leads 1 or 2 connected to L; Leads 3 or 4 connected to N.
- CAUTION: Use only non-shunted lamp holders for Single-edged wiring installations. Do not perform Single-Ended wiring installation of the product in a fixture with shunted lamp holders (found in all fixtures using instant start ballasts).
- If the existing lampholders are shunted and Single-Ended wiring is desired, remove and replace them with non-shunted lamp holders (or remove the external shunt if applicable).
- Make new connections directly to lampholder terminals as shown in Figure 1 below.
- After the wiring modification is completed, attach the replacement cautionary label onto a visible place on the fixture and remove any pre-existing labels.
Typical Non-Shunted Lampholder
Typical Shunted Lampholders
- STEP 4: Install the LED U-bend.
- STEP 5: Turn the ON power. Installation is complete.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>