SATCO NUVO 7 and 10 Inch LED Disk Lights Installation Guide
- June 3, 2024
- SATCO NUVO
Table of Contents
SATCO NUVO 7 and 10 Inch LED Disk Lights
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing the fixture. Retain for future reference..
WARNING: Risk of Fire or Electric Shock
- Disconnect power before installation or maintenance of the fixture.
- This product must be installed in accordance with applicable installation codes by a person familiar with mentioned abovementioned codes and the hazards involved. These fixtures are designed to meet the latest NEC requirements and are listed in full compliance with UL 1598.
- Supply wires must be rated a minimum of 90ºC. If uncertain consult an electrician.
- The product is purposed for interior use only, suitable for wet locations.
- Protect the product against direct contact with water.
- Assemble the product only with the use of the parts provided and the housing; improper assembly may result in the device failing which could damage the product, or personal property or cause injury.
- CAUTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
HARDWARE INCLUDED
WIRING DIAGRAM
INSTALLATION
NOTE: Shut OFF the power at the circuit breaker and remove the existing fixture, including the mounting hardware. Carefully unpack your new fixture and lay out all the parts in a clear area. Be careful not to lose any small parts necessary for installation.
-
Twist the lens cover counter-clockwise to remove from Disk Light.
-
Secure the Crossbar to the Junction Box using Junction Box Screws. Please note the crossbar mounting position.
-
7″ only: Place the Disk Light over the Crossbar and secure it with Junction Box Screws through canopy Keyholes. See Figure 1. Make sure Disk Light is flush to the ceiling.
10″ only: Place the Disk Light over the Crossbar and secure the Crossbar through the canopy Keyholes with Short Crossbar Screws. See Figure 2. Make sure Disk Light is flush with the ceiling. -
Replace the lens back onto the Disk Light by turning clockwise.
ELECTRICAL CONNECTION
Connect the fixture input wires to Junction Box wires as shown in the Wiring
Diagram, making sure all wire connectors are secure.
If the Junction Box has a Ground Wire (Green or Bare Copper), connect the
fixture’s Ground Wire to it. After the wires are connected, tuck them
carefully inside the Junction Box.
Dimming: This product is compatible with most residential-type dimmers
available on the market. The dimming performance will depend on the kind of
dimmer and dimmer settings. Visit Satco.com for an up-to-date list of
compatible dimmers.
Cleaning: Clean with a soft or damp cloth, and make sure the power is
OFF. Do not clean with liquids or abrasives.
5-Year Limited Warranty: The purchased product is covered with a 5-year
warranty in respect of any defect in material or workmanship after the
purchase date. Satco shall bear no responsibility on account of the guarantee,
as well as shall bear no liability for any faults, in case of improper
operation, use negligence, accident or exposure to natural hazard, or
excessive use over the limits specified for the unit, or if any unauthorized
alteration or repair followed.
© Copyright 2022 Satco Products, Inc. 8/22 v1.2
Documents / Resources
|
SATCO NUVO 7 and 10 Inch LED Disk
Lights
[pdf] Installation Guide
7 and 10 Inch LED Disk Lights, 7 Inch LED Disk Lights, 10 Inch LED Disk
Lights, LED Disk Lights, LED Lights, Disk Lights, Lights, 62-1660, 62-1661,
62-1662, 62-1663, 62-1670, 62-1671, 62-1672, 62-1673
---|---
|
SATCO NUVO 7 and 10 Inch LED Disk
Lights
[pdf] Instruction Manual
7 and 10 Inch LED Disk Lights, 7 Inch LED Disk Lights, 10 Inch LED Disk
Lights, LED Disk Lights, LED Lights, Disk Lights, Lights, 62 1660, 62 1661, 62
1662, 62 1663, 62 1670, 62 1671, 62 1672, 62 1673
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>