SATCO 60-7375 Sullivan Large Wall Lantern Instruction Manual
- June 3, 2024
- SATCO
Table of Contents
SATCO 60-7375 Sullivan Large Wall Lantern
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT
OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are
included as shown in figure. Be careful not to misplace any of the screws or
parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Thread the 2 mounting screws (B) into the mounting plate (C) spaced
the same distance apart as the holes in the fixture back plate. (Adjust the
length of the screws if necessary.)
STEP 2: Attach the mounting plate (C) to the outlet box (not supplied) with
mounting screws (D). Ground Wire must face out.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
| GROUP B:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check again for
a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1: Align the fixture back plate (E) to mounting plate (C) and secure
with washer (G) and screws (F).
STEP 2: Install Bulb (1) A19 100W MAX/Medium base (not included).
STEP 3: To prevent moisture from entering the outlet box and causing a
short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant). Outline the
outside of fixture back plate where it meets the wall leaving a space at
bottom to allow moisture a way to escape.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration when
ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>