GREENCUT PIN660C Paint Gun Instruction Manual

PAINT GUN PIN660C
Instruction manual

INTRODUCTION

Thank you for choosing this GREENCUT product. We are confident that you will appreciate its quality and meet your needs for a long period of time.
Remember that you can contact our Official Technical Service for questions about assembly, use, maintenance, identification and troubleshooting and for the purchase of spare parts and/or accessories.

ATENTION: Please read this manual carefully before using the product. Failure to comply with the operating instructions and safety warnings may result in damage to the  user and/or the product itself. The manufacturer is not responsible for accidents and damage to the user, third parties and objects resulting from ignoring the contents of this manual.

This product is not intended for professional use.
Keep this instruction manual for future reference. If you sell this product, remember to give this manual to the new owner.

SAFETY RULES AND PRECAUTIONS

The following symbols and signal words and their meanings are intended to explain the hazards and information related to this product.

full attention to avoid
any kind of personal injuries or damage to the device.
| NOTE| It indicates useful information which can facilitate your task.

ATENTION: Read and understand all warnings and safety instructions before using this product.
Failure to do so may result in electric shock, fire and/or serious injury.
All information in this manual is relevant to your own safety and that of your environment. If you have any questions about the information contained in this manual, consult  a professional or contact the Official Technical Service.
The following information on hazards and precautions includes the most likely situations that may arise during use of this machine. Consult all product documentation,  packaging and labels before use.
If you encounter a situation not described in this manual, use common sense to use the machine as safely as possible and if you see danger, do not use the machine.

USERS

• This product has been designed to be handled by users of legal age who have read and understood these instructions. Do not allow underage persons or persons who do  not understand these instructions to use the product.
•  Before using this product, familiarize yourself with it. Make sure you know where all the controls are, the safety devices and how they should be used.
• If you are an inexperienced user we recommend that you practice doing simple work and, if possible, in the company of an experienced person.

PERSONAL SAFETY

• Don’t force this machine. Use this machine, accessories, tools, etc. according to these instructions, taking into account the conditions and the work to be carried out.  Using this machine for unintended purposes can cause a dangerous situation.
• Be alert, watch what you’re doing when you drive this machine.
• Avoid unintentional start-up of the unit. Make sure the switches are in the off position before connecting the machine to an electrical power source.
• Do not use this machine when tired or under the influence of drugs, alcohol, or medications.
• Check that all security features are installed and in good condition. Do not use this machine if any of its components are damaged. Do not use blunt or bent blades.
• Operate the machine only when it is on a fixed, stable, level surface. Slippery or unstable surfaces may cause a loss of balance or control of the machine.
• Use only coating materials such as paints, enamels, varnishes, etc.
• During spraying, make sure there are no ignition sources nearby: open fire, cigarettes, sparks, incandescent wires, hot surfaces, etc.
• Never point the gun at you or other people or animals.
• Do not place machine under gun while spraying.
• Avoid inhalation of solvent vapours from the appliance. Wear a mask.
• When working outdoors, observe the direction of the wind. When working indoors, make sure there is sufficient ventilation.
• Do not spray the machine.
• Be sure to connect the hose correctly. The device is only splash proof when the air hose is properly connected.
• Do not use guns to spray flammable liquids.
• Do not operate the machine in rain or extreme humidity.
• Do not leave this machine running unattended.

WORK CLOTHES

• Dress appropriately. Do not wear loose clothing or jewelry that could get caught in moving parts. We recommend the use of: Safety glasses, gloves and mask.

SAFETY IN THE WORK AREA

• Do not use the machine at extreme temperatures or in excessively humid environments.
• Do not use this machine in explosive atmospheres in the presence of flammable liquids, gases and dust.
• Keep the work area clean and well lit. Cluttered, dark areas can cause accidents.
• Remove all objects from the work area before starting this machine. Objects near the product may be touched and projected by the machine causing personal injury.
• Keep children, people, or animals away while operating this machine.
• Remember that the machine operator is responsible for hazards and accidents caused to other people or things.
  Under no circumstances shall the manufacturer be liable for damage caused by improper or incorrect use of this machine.

ELECTRICAL SAFETY

• This equipment may be a potential source of electric shock if used improperly.
• Make sure all power supplies meet equipment voltage requirements before connecting or disconnecting equipment.
• Keep the machine away from water and excessive moisture.
• Do not use electrical cords to lift, move, or transport equipment. Protect cables from heat and sharp objects.
• Make sure that the electrical cables do not present a risk of tripping.
• When working outdoors, only use approved extension cords.

SAFETY IN MAINTENANCE, TRANSPORT AND STORAGE

• Do not modify product controls.
• Check regularly for broken parts or other conditions that may affect the proper operation of the machine.
• Replace worn or damaged parts immediately with original spare parts only.
• Carry out regular maintenance on the machine. Do not attempt any maintenance or repair work not described in this instruction manual. We recommend that  maintenance and repairs not described in this manual are carried out by the Official Technical Service.
• At the end of the work, always clean the machine of dust and dirt.
• Turn off and disconnect the machine completely before making any adjustments, changing accessories, servicing, transporting, or storing this machine.
• Do not clean the equipment with solvents, flammable liquids or strong abrasives.
•  Transport the machine through the base. Do not move it by pulling on the power cord.
• The equipment is not weather resistant, and should not be stored in direct sunlight, high ambient temperatures, or in humid or wet locations.
• Store the product out of the reach of children.

SERVICE

• Have the product checked periodically by a qualified technician and use only original spare parts. If you have any questions, please contact the Official Technical Service.

WARNING ICONS

The icons on the warning labels on this machine and/or in the manual indicate information necessary for the safe use of this machine.

| Attention, danger!
---|---
| Read this manual carefully before starting the machine.
| Use eye protection.
| Wear a face mask to protect against dust, steam and other toxic fumes.
| Use resistant and anti-slippery gloves.
| Do not expose to rain or damp conditions.
| Risk of electric shock.
| Keep unprotected people away and at a safe distance from the work area.
| Keep children away from this machine.
| Danger of projection of flying debris. Be careful with all projected materials.
| Turn off the machine and disconnect it completely before servicing the machine.
| Guaranteed sound power level XX LWA, dB (A).
| Dispose of your device in an environmentally friendly way. This product should not be disposed of with household waste.
| Complies with the European Union Directive.

PRODUCT DESCRIPTION

CONDITIONS OF USE
Use this machine with oil- and water-based products recommended for spray use, including paint, varnish, stains, and wood preservatives. Do not use the machine for  emulsions with wall paints, bleaches or other acid coating materials. Any use other than that described above may cause dangerous situations and exempts the manufacturer from any liability.

DETAILED DESCRIPTION OF THE PRODUCT

1. Hose Mouth
2. Air nozzle
3. Spray gun
4. Trigger
5. Spray Control
6. Container
7. Wheels
8. Knob
9. Air Hose
10. Power cord
11. ON/OFF switch
12. Handle
13. Handle close/open

NOTE: The products detailed in this manual may vary in appearance, inclusions, description and packaging as shown or described here.

TECHNICAL DATA

PAINT GUN

NOTE: GREENCUT reserves the right to modify the technical data without prior notice.

BOX CONTENTS

1. 1 Electric Paint Gun
2. 1 Viscosity measuring cup
3.  1 Nozzle Cleaner

• Remove the product and accessories from the box. Make sure all items are present.
• Inspect the product to ensure that it has not been broken or damaged in transit.
• Do not discard the packaging material until you have carefully inspected and satisfactorily used the product.

ATTENTION: If any part is missing or damaged, please contact the Official Technical Service. Do not use this product without replacing the part. Using this product with  damaged or missing parts can  cause serious injury to the operator.

PRODUCT USE

BEFORE COMMISSIONING
ATTENTION: The gun cannot be used for paints such as textured paints for exterior walls, materials containing abrasive substances, enamels, dispersion paints, caustic and  alkaline substances or textured coatings. To get the best results from your spray gun, read the instructions carefully before use.

PREPARATION OF THE COATING MATERIAL
The paints need a previous dilution to be able to use it in the spray gun. The following information indicates the recommended dilutions for paints according to their viscosity. (viscosity = consistency of material).

VISCOSITY CHART

VISCOSITY MEASUREMENT
Use the measuring cup to determine the viscosity grade of the coating material.

1. Mix the coating material well before starting the measurement.
2. Immerse the viscosity measuring cup (content 100cm3) completely in the coating material underneath the cup.
3. Lift the viscosity measuring cup and measure the time it takes for the cup to empty in seconds.

COMMISSIONING

AIR HOSE CONNECTION

1. Connect the air hose to the end of the mobile base. Align the tongue with the groove on the movable base. Secure by turning counterclockwise.
2. Connect the other end of the air hose to the gun. Align the tab with the slot in the gun. Secure by turning counterclockwise.
3. Unscrew the paint can from the spray gun.
4. Adjust the suction tube properly. It should be possible to spray the contents of the paint can leaving little paint in the paint can.

SPRAYING
HORIZONTAL AND OVERHEAD OBJECTS

1. Rotate the suction tube inside the container pointing towards the front of the gun.
2. Rotate the suction tube so that it points backwards, as the suction tube must point towards the back of the spray gun to expel the entire contents.

FILLING THE PAINT CAN

1. While filling the can with paint, filter the paint through a piece of nylon stocking or a funnel that incorporates a filter to remove any lumps or particles. Do not overfill.
2. Screw the canister onto the spray gun making sure it is securely fastened.

CONNECTION

1. Place the spray gun on the mobile stand of the machine base to transport it to the job site.
2. Unwind the connecting cable. Insert the plug into the outlet and turn it on.
3. Remove the spray gun from the gun holder on the mobile base and point it at a piece of cardboard or newspaper. Switch on the machine with the ON/OFF switch on the mobile base.

NOTE: When the mobile base is connected, air flows continuously from the air cap.

ADJUSTING THE SPRAY GUN

1. Squeeze the trigger while pointing the gun at a piece of cardboard or scrap material and wait for the spray to come out.
2. Turn the sprayer control dial to the desired position for optimal results.

NOTE: The spray control dial is a stop that limits the distance at which the trigger can be pulled.

CHOICE OF SPRAY TYPE
To select the spray type (b), with the air cap loosened (a), rotate the air nozzle to the desired spray pattern.

TYPES OF SPRAYING
A = vertical sprinkler – for horizontal surfaces
B = horizontal sprinkler – for vertical surfaces
C = round sprinkler – for corners, edges and other hard-to-reach places.

SPRAYING TECHNOLOGY

ATTENTION: The surface must be carefully prepared and kept free of dust. Surfaces and parts that are not to be sprayed should be masked by covering them with masking tape and newspaper.” Always keep the spray gun at an even distance from the object to be sprayed. The distance will vary depending on the type of paint being sprayed, it is suggested to start with  20 cm and adjust if necessary. Depending on the set spray effect, move the spray gun evenly upwards or downwards.
The movement of the spray gun should be by the arm and not by the wrist to ensure that the space between the gun and the surface remains the same throughout the operation.

The uneven movement of the pistol gives an uneven surface quality. A uniform movement of the spray gun provides a uniform surface quality.

If the coating material accumulates in the nozzle (b) and air cap (a). Remove the air cap nut and air cap (a). Clean both parts and around the nozzle (b) with solvent or water with a stiff brush. If the nozzle (b) is blocked, it can be removed with a 9 mm open-end wrench, carefully unscrew it from the paint head. Clean nozzle (b) and remove any accumulated paint. Be careful not to damage the nozzle (b), as this will affect the performance of the gun.

MAINTENANCE

Good maintenance will extend the life of the machine. Prolonged or constant use may require more intensive maintenance for the machine to continue to function properly.
ATTENTION: Make sure the machine is completely turned off before performing any maintenance or repairs. This will eliminate any potential risks.

CLEANING AFTER EACH USE

1. Turn off the device. Open the trigger to bring the spray gun coating back into the container.

2. Unscrew the container. Return the remaining material to the material container.

3. Clean container. Remove the suction tube by turning it counterclockwise and gently pull it away from the paint head.
   Disassemble the suction tube for cleaning by turning it clockwise and pulling to disassemble.

4. Clean the 3 holes in the suction pipe, if blocked, with the cleaning needle supplied. If these holes are partially blocked, the result will be uneven and inconsistent spraying.

5. Thoroughly clean the suction pipe with water or solvent before reassembling.

6. Replace the suction tube and fill the container with solvent or water.

7. Screw the container into place. Turn on the device and spray the solvent or water into a container.

8.  Repeat the above procedure until water or clear solvent comes out of the nozzle.
   NOTE: Only use a solvent with a flash point above 21°C.

9. Turn off the device.

10. Then empty the container completely. Always keep the closure of the container free of liner material and check for damage.

11. If the gun casing requires cleaning, immerse a cloth in the solvent or water, making sure the cloth does not leak, clean the outside of the spray gun.

12. Unscrew the nut from the air cap. Remove the air cap. Clean the air cap and nozzle with a brush and solvent or water.

13. Before storing the Mobile Paint Unit, make sure it is completely dry. This will minimize the accumulation of waste for the next use.

CLEANING THE PISTON OF THE PISTOL
If the paint has dried in the paint head or the spray gun has had a lot of use, removing, cleaning or replacing the plunger can restore the original performance of the spray gun.
To clean the plunger:

1. Remove the air hose from the spray gun. Carefully unscrew the piston from the pistol with an 8 mm sleeve (not supplied) and remove it from the back of the pistol.
2. Clean plunger and spray gun assembly, remove paint with clear solvent or water.
3. After cleaning, reassemble the plunger in the correct order and place it on the back of the spray gun.

TROUBLESHOOTING

The table includes some of the most common problems, their causes and remedies.

nozzle
Suction pipe is blocked| Clean the suction pipe
The hole in the suction pipe is clogged| Clean the suction pipe
The spray control dial on the material  has turned too far toward (-)| Turn the regulator dial (+) clockwise
Suction tube is loose| Tighten the tube
No pressure build-up in the paint can| Tighten the paint can
Coating material drips from nozzle| The nozzle is loose| Tighten the nozzle
The nozzle is worn.| Change nozzle
Accumulation of coating material in the air cap and nozzle| Clean air cap and nozzle
Spraying too coarse| The coating material has too high a viscosity| Dilute the coating material
Too much material, the spray control dial has turned too much to (+).| Turn the sprayer control dial to (-)
The nozzle is dirty| Clean nozzle
Very dirty air filter| Change the air filter
Not enough pressure build-up in
the paint can| Tighten the paint can
The spray jet emits impulses| The coating material in the paint container is running out.| Fill Paint Container
The small hole in the suction tube is blocked.| Clean the suction pipe orifice
The air filter is very dirty| Change the air filter
Too much vaporization of the  coating material (overspray)| The distance to the object to be sprayed is too great| Reduce spray distance
Too much coating material applied| Turn the knob on the media spray control to position (-)

NOTE: If you are unable to resolve the problem, please contact the Official Technical Service.

TRANSPORTATION AND STORAGE

• Allow equipment to cool completely before transporting or storing.
• Always store the product in a clean, safe, dry place with temperatures between 0º and 45ºC.
• The equipment is not weatherproof, and should not be stored in direct sunlight, high temperatures, or in humid locations.
• Clean the machine of traces of coating material before storing.
• Store the machine out of the reach of children.

RECICLYING AND DISPOSING

Worn products are potentially recyclable and should not be disposed of in the usual waste. Help us to protect the environment and preserve natural resources.
Dispose of the device in an environmentally friendly manner. Do not dispose of it with household waste. Its plastic and metal components can be separated and recycled.  Take this appliance to an approved recycling centre (green point).
Gasoline, used oils, oil/gasoline blends and objects stained with gasoline (e.g., rags) should not be disposed of in regular trash, sewage, dirt, rivers, lakes or the sea. Oil-stained  items should be disposed of in accordance with local regulations: take them to a recycling center.
The materials used in the packaging of the machine are recyclable: please dispose of them in the appropriate container.

GUARANTEE

GREENCUT guarantees all GREENCUT products for a period of 24 months (valid for Europe). The warranty is subject to the date of purchase taking into account the  intended use of the product.
As a condition subject to warranty, the original receipt must be presented indicating the date of purchase and its description as well as the defective tool.
The warranty does not cover normal wear and tear, especially on blades, blade fasteners, turbines, light sources, fan and transmission belts, impellers, air filters, spark plugs  and damage caused by improper use, especially noncompliance with operating and maintenance instructions.
In the event that repairs or modifications have been made by the consumer or other than with original GREENCUT spare parts, the warranty will be voided.
In the event of a justified warranty claim, we are entitled, at our discretion, to repair or replace the defective tool free of charge. Other claims beyond this warranty are not valid.

DECLARATION OF CONFORMITY (EC)

We, PRAT INTERNATIONAL BRANDS S.L., owner of the GREENCUT brand, based in Calle Blanquers (plot 7-8) Valls Industrial Estate. 43800 -, SPAIN, we declare that the paint gun PIN900C from the serial number of the year 2018 onwards, are in compliance with the requirements of the applicable European Parliament and Council  Directives:

• Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC.
• Directive 2004/108/CE of the European Parliament and of the Council of 15th December 2004 on the approximation of the laws of the Member States relating to  electromagnetic compatibility and repealing Directive 89/336/EEC.

The product delivered coincides with the specimen which was subjected to EC type-examination.
Valls (SPAIN), September 3, 2018,

Albert Prat Asensio, Founder (Authorized Representative and responsible for technical documentation).

www.greencut.es
Manual revised eon September de 2021

Documents / Resources

| GREENCUT PIN660C Paint Gun [pdf] Instruction Manual
PIN660C Paint Gun, PIN660C, Paint Gun, Paint, Gun
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>