LUMINO V36I OPTIC Installation Guide

June 6, 2024
LUMINO

LUMINO logo

LUMINO V36I OPTIC

LUMINO V36I OPTIC product

HANDLING PRECAUTIONS

GLASS
Take extra care with glass when handling the product. Glass can be chipped, if hit on the edge against hard objects. Do not apply pressure with small or sharp objects to the lass. Glass is rated for a walk-over use.
POWER CABLES
The product end caps, power cables, and connectors must not be pulled or twisted. Never pull the product by its power cables or hang it from its power cables or connectors.
IMPACT PROTECTION AND STATIC LOAD
This product has a maximum IK rating of IK09 and can resist a maximum 5kN/min static load. The product is not vandal resistant.
CUTTING AND SAWING
The product must not be cut, sawn, drilled, or otherwise modified in any way.
DAMAGES
Inspect the product and if you see any damage upon unpacking report to LUMINO immediately and do not install the product
LOCATION
Suitable for wet and damp locations. IP68 rated for temporary submersion. Max depth. 1.2M / Max duration. 30mins. Ensure there is adequate drainage made available for the product. Protect product from dust, paint and harmful substances during installation and use. Ensure the product is not exposed to VOC gases. Do not obstruct the product and its light output.

SAFETY GUIDANCE

WIRING GUIDE
Follow the guidance shown in the provided wiring guide, including maximum cable lengths, cable sizes, and other wiring instructions. When running cables through an enclosure, ensure cables are protected from damage, separated from mains voltage cables, and anchored against being pulled. Make connections appropriate for the IP rating of the product.
QUALIFIED INSTALLER
Installation must be carried out by a qualified person and conducted in accordance with local regulations and applicable standards.
THERMAL MANAGEMENT
Ensure ambient temperature (Ta) does not exceed 40°C (104°F) and case temperature (Tc) does not exceed 70°C (158°F). Exceeding maximum Tc will cause permanent damage and void the product warranty. Allow sufficient clear air space for the LED drivers, as well as suitable access to the drivers as specified in installation instructions.
REPAIR AND REPLACEMENT
If the product is not functioning, contact LUMINO to register a Service Call for factory repair or replacement. The light source is not user-replaceable. See page 4 for Ecodesign and end-of-life information.

DRIVERS

POWER OFF
Product and driver must not be live wired. Switch off the power before work begins. Follow instructions and guidance for the make and model of the driver being used.
CONSTANT CURRENT DC
Ensure supply current does not exceed 350mA or 500mA (see product label). Drivers must be the constant current type with both overload and short-circuit protection. Exceeding the stated voltage or current will cause permanent damage and void the product warranty.
DIMMERS
Check dimmer is compatible with the driver and certified to local regulations.
INRUSH CURRENT
Many LED drivers can have high inrush current at power-on. Driver inrush current can be many times the normal operating current. Use a suitable MCB. Type C MCBs are normally suitable but if inrush current is a persistent problem an inrush suppressor may be required.
PROTECTION
Use only with constant current Class 2 power unit to UL1310 standard with overload and short-circuit protection. Rate drivers for at least 10% above load. Driver protection circuitry must not be relied upon to protect secondary electrical circuits from damage caused by over-voltage or short circuit. DC fuses or DC electronic circuit breakers are recommended for full protection. Allow for access to drivers for maintenance and sufficient clear air space for ventilation.
CABLING
Do not overload the driver. Damage will be caused by incorrect input voltage, reverse polarity, or a short circuit. Plan for loads, driver locations, dimming, and cabling prior to the start of work. Ensure basic insulation is maintained between mains and dimming control wires.

ACCESSORIES

LUMINO V36I OPTIC fig-1

Cable VECA-CA010-R1 2 Core 0.75mm² cable 10m cable lengthLUMINO V36I OPTIC
fig-2

Connector VECA-CA003-R1 2 Pole connector Up to 4 cables

Ground Channel V36G-B2050-R1 2050mm Profile Site cuttable

Ground Channel End Caps V36G-MB202-R1 2pcs end caps

Ground Channel Joining Kit V36G-JB203-R1 Joining kit

Clips V36G-MB201-R1 10pcs clips 4 pairs per meter

Removal Tool V36I-MA204-R1 1pcs tool

**CHECK FIRST!

LUMINO V36I OPTIC fig-8**

INSTALLATION

Plan Installation
Check product and its dimensions against the planned installation. Runs of LEDs may have to be installed in a particular sequence.LUMINO V36I OPTIC
fig-9

Prepare Power Supply
This product requires a 350mA or 500mA (see product label) constant current power supply. Please refer to the provided wiring guide document. Failure to follow the guidelines may result in damage to the product and voiding of the warranty.LUMINO V36I OPTIC fig-10

LED driver must be located somewhere suitable for its IP rating. All connections made to and from the LED driver must be IP rated.

Install Clips
See V36G installation manual for instructions for ground channel installation. Insert and equally space the retaining clips into the channel. 4 pairs per meter for a secure hold.LUMINO V36I OPTIC fig-11

Connect Cable

Connect cables using VECA-CA003-R1 IP68 connector.

  • Local regulations must be observed.
  • Do not exceed the current rating on the product label.
  • Do not hot-wire the luminaire.

Please refer to provided wiring guide document. Failure to follow the provided guide may result in damage to the product and voiding of the warrantyLUMINO
V36I OPTIC fig-12

Test V36I
Verify that the circuit is working. Then lower the V36I into the V36G channel. If the product does not function as expected, turn the power off immediately and check all connections.LUMINO V36I OPTIC fig-13

Cables
Make sure not to pinch any cables within the channel. Take care to tuck the cables beneath the V36G’s internal lip (see diagram).

Silicone
Silicone around the glass edge and the V36G create a good watertight seal and allow to dry for 6 hours.LUMINO V36I OPTIC fig-15

Clean
Clean using a glass cleaning cloth and glass cleaning solution. The profile must be checked every 12 months and cleaned to maintain the warranty.LUMINO
V36I OPTIC fig-16

ECODESIGN REGULATION

This product is considered to be a “containing product” in the sense of Regulations (EU) 2019/202 (EU) 2019/2015. The contained light source is an integrated part of the containing product and its removal can only  be done by causing permanent
damage to the containing product.
Therefore, replacement of the light source with the use of commonly available tools is not justified due to its restricted mechanical, electrical, optical, thermal, and/or environmental protection requirements.

DISMANTLING

Dismantling of the light source from the containing product at end of life: The containing product shall be cut to the length of the contained light source and the light source mechanically detached from the containing product. Containing product component parts shall then be disassembled. Containing products shall be separated from building material and/or from other additional mounting accessories by means of a professional installer. Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. LUMINO is a member of the WEEE producer compliance scheme. Registration number: WEE/MM8138AA

ENERGY RATING

This product contains light sources of energy efficiency classes as shown:

LED CCT 60W/m

ColorCORE

| 4000K| F
3500K| F
3000K| F
2700K| F

**LED Driver Wiring

LUMINO V36I OPTIC fig-17**

LUMINO V36I OPTIC fig-18 Observe maximum cable lengths – as shown above, or as specified by the driver manufacturer, whichever is the shortest. Longer cable lengths increase EMI susceptibility.

**Wiring Diagram

LUMINO V36I OPTIC fig-19**

LUMINO V36I OPTIC fig-20

Cable lengths are based on average resistance for typical copper cables. Cable characteristics may vary according to manufacturer, temperature, copper purity, connections, etc.
For further help regarding installation visit lumino. lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals