PHILIPS CN-SBM210 Portable Microphone Loudspeaker User Manual
- June 4, 2024
- Philips
Table of Contents
Portable Microphone Loudspeaker
User Manual
CN-SBM210 Portable Microphone Loudspeaker
Before using your product,read all accompanying safety information.
- AUDIO IN
- MIC IN
- DISPLAY
- ANTENNA
-
-
-
- SOURCE
- HOOK
- USB
- MICRO USB
- TF CARD
- POWER ON/OFF VOL+-
- CHARGING INDICATOR
REC
Preparation for Recording
- Connect the headset microphone to the M IC slot.
- Insert a USB flash disk or a TF card into the speaker.
Recording Procedure
- Press the SOURCE key to switch to Recording Mode(as shown in Fig.1.2)
- Press ****to start recording(as shown in Fig.3.4)
- Long press ****to end recording and store the audio file into the USB flash disk or TF card(as shown in Fig.5)
- Listen to your recordings: Press the SOURCE key to switch to MP3 mode, and press ****to listen to your latest recording. (as shown in Fig.6.7.8)
Power On/Off
Rotate the volume knob clockwise/anticlockwise to turn the speaker on or off.
Tips: When the speaker is not connected to any signal source and there is
no operation for 15 minutes. The speaker will automatically enter into power-
saving mode. You need to switch the knob off and then switch on to wake up the
speaker.
Wired Microphone Instructions
Please direct the positive hole of the wired microphone to your mouth when using it. If you do not direct the positive side to your mouth,it might be a howling or weak sound. Please do not forget to use black cotton. The black cotton can filter the interfering sound with the airflow. ( Lock Touch Key: double press the SOURCE key quickly to lock the touch operation. You will hear a voice prompt. Unlock Touch Key: double press the SOURCE key again to unlock the touch operation. You will hear twice the voice prompt. The touch key will be automatically locked after 20 seconds with no operation in the microphone mode.)
AUDIO IN Mode
Connect your Audio in the cable to the AUDIO IN socket, there will be voice
prompts and the speaker will enter into the AUDIO IN mode automatically.
FM Radio Mode Instructions
Search FM Radio stations automatically: Short press the SOURCE key to select an FM source. When you enter FM radio mode for the first time, press and hold the key for two seconds to scan and save stations automatically. Press or to switch to the previous or next station. Search FM Radio stations manually: In FM Radio Mode, press and hold or key for two seconds, When the display frequency is blinking. Press or **to switch to your favorable station, press the key to save it. Press and hold **the key for 2 seconds to exit. Clear the radio station: In FM mode, long press the SOURCE button for 5 seconds, it will clear all radio stations, and at the same time there will be voice prompts
Charging Instructions: Blinking continuously while the low battery, voice
prompts to remind you to charge the speaker.
****The Red indicator keeps solid while charging, Red indicator is off when
gets fully charged. It takes around 3 hours to get the battery fully charged.
Bluetooth Mode Instructions
- Press the SOURCE key to switch to Bluetooth pairing mode. The bLUE icon blinks on the screen and there is a voice prompt.
- Activate Bluetooth of your phone or device, scan for “Philips SBM210”, click and connect successfully, the blue icon keeps solid on the screen, and there is a voice prompt that the Bluetooth is connected.
Safety
Important Safety Instructions
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Do not block any ventilation openings] install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Devices shall not be exposed to dripping or splashing.
- Do not place any sources of danger on the device(e.g. liquid filled objects, lighted candles).
Always bring your product to a professional to remove the built-in battery.
Environmental information All unnecessary packaging has been omitted. We have
tried to make the packaging easy to separate into three materials: cardboard
(box), polystyrene foam (buffer), and polyethylene (bags, protective foam
sheet.)
Your system consists of materials that can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, exhausted batteries, and old
equipment.
Note
- The type plate is located at the bottom of the apparatus.
MP3 Mode Instructions
Set loop one/loop all playing: In MP3 mode, the default setting is loop all.
If you want to play the current track repeatedly, press and hold for 2
seconds while playing, and there will be voice prompts to tell you the loop
one function has been enabled. To enable the loop all function, press and hold
for 2 seconds again, there will be voice prompts to tell you the loop all
function has been enabled.USB flash disk and TF card support 32GB max. Audio
format: support MP3 / WMA / WAV (sampling frequency 8k-48k)
Specifications
Rated Output Power | 3W RMS |
---|---|
Signal-to-Noise Ratio | 50dBA |
Aux Input | 600mV RMS,22 ohm |
Power Supply | 5V ****0.5A |
Built-in Battery | lithium battery |
Dimensions – Main Unit | ‘(W x H x D) 90 x116 x 32 mm |
Weight -Main Unit | 0.198kg |
Warning
- Never remove the casing of this apparatus.
- Never lubricate any part of this apparatus.
- Never place this apparatus on other electrical equipment.
Notice
Any changes or modifications made to this device that are not expressly
approved by MMD Hong Kong Holding Limited may void the user’s authority to
operate the equipment.
Disposal of your old product
Your product is designed and manufactured with high-quality materials and
components, which can — be recycled and reused.
Do not throw away the product with the normal household waste at the end of
its life, but hand it in at an official collection point or recycling. By
doing this, you help to preserve the environment.
Caution
- Removal of the built-in battery invalidates the warranty and may destroy the product.
Names and Contents of Hazardous Substances
Name of the Parts | Hazardous Substances |
---|---|
(Pb, I Pad) | (Hg, Mercury) |
Housing | 0 |
Loudspeakers | 0 |
PWBs | X |
Accessories (Cables) | X |
The table is compiled according to SJ/T 113641
0: Indicates that this hazardous substance part is below the limit requirement
in contained in all of the homogeneous materials for this /T 26572.
X: Indicates that this hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit req increment in
GB/T 26572.
Environmental Protection Use Period
This logo refers to the period (10 years) di_ ring which the hazardous
substances in electronic and electrical products will not leak or mutate so
that the use of these [substances) will not result in any severe environmental
pollution, bodily injury, or damage to any assets.
2021 MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.
CN-SBM210/93-UM-3.0
Be responsible
Respect copyrights
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>