LUMINO V12S IP50 Lighting

June 6, 2024
LUMINO

V12S IP50
INSTALLATION MANUAL
IMV12S_IP50_R2102

TECHNICAL SUPPORT
+44(0) 1279 635 411 www.lumino.lighting
LUMINOX DISTRIBUTION LTD
Lumino House, Lovet Road Harlow, Essex CM19 5TB United Kingdom
Installers must read this document and any other referenced documents in full before commencing installation work. Failure to observe all installation guidance in this document may result in unsafe installation, cause permanent product damage and void product warranty.
This document is subject to change without notice. Check for the latest documentation with LUMINO. Copyright © LUMINO. E&OE

HANDLING PRECAUTIONS

PLASTIC COVER / DIFFUSER
To avoid permanent damage, do not allow small or sharp objects to apply pressure on to the plastic cover/diffuser.
STRESS
Never stand or place weighted items on the product. The product is not vandal resistant and has no IK rating. Do not subject the product to impact forces.
POWER CABLES
The product end caps, power cables, and connectors must not be pulled or twisted. Never pull the product by its power cables or hang it from its power cables or connectors.
CUTTING AND SAWING The  product must not be sawn, drilled, or otherwise modified in any way.
DAMAGES
Inspect the product. If you see any damage upon unpacking, report to LUMINO immediately and do not install the product.
LOCATION
Use in dry locations only. This product is unsuitable for wet and damp locations. IP50 rated for dust protection.
Protect products from dust, paint, and harmful substances during installation and use. Ensure the product is not exposed to VOC gases. Do not obstruct the product and its light output.

SAFETY GUIDANCE

WIRING GUIDE
Follow the guidance shown in the provided wiring guide, including maximum cable lengths, cable sizes, and other wiring instructions. When running cables through an enclosure, ensure cables are protected from damage, separated from mains voltage cables, and anchored against being pulled. Make connections appropriate for the IP rating of the product.
QUALIFIED INSTALLER
Installation must be carried out by a qualified person and conducted in accordance with local regulations and applicable standards.
THERMAL MANAGEMENT
Ensure ambient temperature (Ta) does not exceed 40°C (104°F) and case temperature (Tc) does not exceed 70°C (158°F). Exceeding maximum Tc will cause permanent damage and void the product warranty.
Allow sufficient clear air space for the LED drivers, as well as suitable access to the drivers as specified in installation instructions.
REPAIR AND REPLACEMENT
If the product is not functioning, contact LUMINO to register a Service Call for factory repair or replacement. The product’s light source is replaceable by a qualified professional. See page 3 for Ecodesign and end-of-life information. DRIVERS
POWER OFF
Product and driver must not be live wired. Switch off the power before work begins. Follow instructions and guidance for the make and model of the driver being used.
24VDC SELV Only uses drivers with a maximum output of 24VDC. Drivers must be SELV, constant voltage with both overload and short-circuit protection.
DIMMERS
Check dimmer is compatible with the driver and certified to local regulations.
INRUSH CURRENT
Many constant voltages LED drivers can have a high inrush current at power-on. Driver’s inrush current can be many times the normal operating current. Use a suitable MCB. Type C MCBs are normally suitable but if inrush current is a persistent problem an inrush suppressor may be required.
PROTECTION
Use only with 24VDC Class 2 power unit to UL1310 standard with overload and short-circuit protection. Rate drivers for at least 10% above load. Driver protection circuitry must not be relied upon to protect secondary 24VDC electrical circuits from damage caused by over-current or short circuits. DC fuses or DC electronic circuit breakers are recommended for full protection. Allow for access to drivers for maintenance and sufficient clear air space for ventilation.
CABLING
Do not overload the driver. Damage will be caused by incorrect input voltage, reverse polarity or short circuit. Plan for loads, driver locations, dimming, and cabling prior to the start of work. Ensure basic insulation is maintained between mains and dimming control wires.
ACCESSORIES
Cable & Connector
VECA-CA0250- MF-R1 2 / 4 Pole power link 250mm cable length
VECA-CA1000- MF-R1 2 / 4 Pole power link 1000mm cable length
IDC Connector
VECA-CA90 -R1 Sealant
connector. 1 – 3A Max / 3 – 5A Max. Pair
Self-closing Cable Sleeving
VECA-SL001-R1 1000mm Cable sleeving
Fixed Mount
V12S-MA -R1 20/100/500pcs Fixed clip S – Silver / B – Black W – White
Rotation Mount
V12S-MA -R1 20/100/500pcs Rotation clip S – Silver / B – Black W – White
IMV12S_IP50_R2102
CHECK FIRST!
TURN OFF POWER! COUPER LE COURANT! STROM ABSHALTEN! CORTE CORRIENTE!
CHECK THE WALL! VËRIFIER LE MUR!
DIE WAND ÜBERPRÜFEN! COMPRUEBE LA PARED!

INSTALLATION

1. Plan Installation
Check product and its dimensions against the planned installation. Runs of LEDs may have to be installed in a particular sequence. 2. Prepare Power Supply
This product requires a 24VDC power supply.
Please refer to provided wiring guide document. Failure to follow guide may result in damage to the product and voiding of the warranty. 3. Mounting Clips
Fix all the clips securely to the mounting surface. Recommended screw size is an Nº 4 gauge wood screw. If necessary, use alternative fixings of a similar gauge and size suitable for the material being fixed into.

Products should be held by at least 3 equally spaced clips per meter. Products that are shorter than 505mm may be held by just 2 clips. There must always be a clip within 100mm of each end of the product.

4. Install V12S Align clips and carefully push the product into the clips. Ensure the product is fully clipped in place and check it is not misaligned or misplaced due to screw heads or wires. Ensure that cables are not pinched when installed.
5. Connect to LED Driver With the power off. Feed the power cables to the V12S, connecting the product to the LED driver. Finalize all electrical connections and test the circuit. If the product does not function as expected, turn the power off immediately and check all connections.

For further help regarding installation visit lumino. lighting

REPAIR & REPLACEMENT
VERY IMPORTANT! PLEASE READ BEFORE CARRYING OUT ANY WORK!

This product’s light source is only replaceable by a qualified professional.
If the product has stopped working, please review the following before replacing the light source. It is important to identify why the product has stopped working first, as replacing the light source might not fix the cause of the failure.
When installed correctly, LEDs have a long service life, with light output gradually decreasing over time (L70 60k hrs, 70% light output after 60,000 hours of use).
Check the lighting circuit.
Was the correct power source used? Check the product label for requirements.
Are there nearby heat sources that might overheat the product? See the first page for maximum Ta and Tc details.
All work must be done by a qualified professional and carried out in accordance with local regulations. All tools required to replace the light source are commonly found tools. Please contact LUMINO if further assistance is required.
It is the full responsibility of the professional carrying out the repair work to ensure that after the work is complete, the repaired product still complies with all relevant safety standards and is safe to use. LUMINO cannot accept liability for any harm resulting from an unsafe repair. If in any doubt, do not carry out repair work and contact LUMINO for support.
TOOLS & PARTS LIST
Tools & Consumables Required

  • Isopropyl alcohol
  • T8 Torx screwdriver
  • Scissors
  • Small hole punch tool (Ø1.2mm)
  • Soldering iron
  • Solder wick/sucker
  • Solder (lead-free)
  • Wire cutters

Spare Parts
The following spare parts are available to order. Please contact LUMINO if any spare parts are required.
Diffusers
V12S Clear diffuser
V12S Opal diffuser
Instructions are meant for IP50 rated products only. Do not attempt to repair the IP67 version of this product and instead contact LUMINO if a repair is required.
4. Move the Product
Move the V12S to an ESD-safe workspace. Take all necessary ESD precautions where appropriate.
1. Turn off the power.
Make sure no electricity can reach the LED power supply. 2. Check Product Label
See the product label and check the specification of LED tape inside. Replacement power output should match or be no greater than that of the original LED tape.
3. Disconnect V12S from the LED driver.

4. Move the Product
Move the V12S to an ESD-safe workspace. Take all necessary ESD precautions where appropriate. ****5. Remove End Caps Carefully remove the end caps from the V12S using a Torx T8 bit.
6. Remove Diffuser Slide plastic diffuser off from the V12S. Take care not to damage the diffuser.

For further help regarding installation visit lumino. lighting
7. Unsolder Cable
Unsolder the individual wires from the LED tape. Solder and solder wick may be required to complete this step. Once the solder pad is at the correct temperature, pry closest end and slowly lift the LED tape away from the wires.

8. Remove LEDs Remove the original LED tape. Lift one end of the LED tape and unpeel from the profile.
9. Recycling
Dispose of electronic waste in accordance with local environmental regulations. Do not send to landfill. 10. Clean

10. Remove any remaining adhesive residue inside the V12S profile. Use isopropyl alcohol if necessary and allow to air dry.
11. Measure LED Tape
Layout the new LED tape, measuring how much is required. V12S profile’s length should closely match the cut increments of the LED tape.

12. Trim LED Tape Cut between solder pads using scissors. LED tape cut increments shown on right.

13. Punch Holes
Using a small hole punch tool, create Ø1.2mm holes in the LED tape as shown.


The hole position must match up with the cable entry hole on the V12S’s profile. See hole offsets set on the right.
14. Solder Cables
With the paper backing still applied. Resolder the cable/s to the LED solder pads. Take care not to overheat the pads.
IMPORTANT: Observe LED tape’s polarities!

Wiring Diagram

15. Install LED Tape
Peel back 50mm to 100mm of the adhesive backing, starting with the hole punched end of the LED tape. Carefully align the beginning of the tape with the start of the V12S extrusion. Simultaneously unpeel backing and press down on the LED tape, working along the length of the profile. Only use finger/thumb pressure on the LEDs.
16. Test LED
Before any further work is done. Momentarily power the LED to verify that the cable was soldered to the LED tape correctly and that the tape itself is functioning.
17. End Cap & Gasket
Install one end cap with a gasket, using a Torx T8 screwdriver onto one end of the V12S. Hand tightens the screw, do not over-torque.

18. Install Diffuser
Slide the diffuser fully into the V12S. Then complete the build by attaching the final end cap and gasket. Hand tighten screw, do not over-torque.

19. Reconnect
With the power off, reconnect the V12S to the LED driver.
20. Power Up
Test the V12S. If the product does not function as expected, turn the power off and inspect all connections.

ECODESIGN REGULATION

This product is considered to be a “containing product” in the sense of Regulations (EU) 2019/2020 and (EU) 2019/2015.
The contained light source is replaceable only by a qualified professional.
This product contains a light source of energy efficiency class as shown in the Energy Rating table. Replacement light sources must be of equal or higher energy rating. Full electrical, mechanical, thermal, and optical functionality must be restored by a qualified professional when the light source is replaced.

DISMANTLING
Dismantling of light source from the containing product at end of life:
The product shall be disassembled in accordance to the provided instructions.
Containing products shall be separated from building material and/or from other additional mounting accessories by means of a professional installer.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK.
LUMINO is a member of the WEEE producer compliance scheme. Registration number: WEE/MM8138AA
ENERGY RATING
This product contains light sources of energy efficiency classes as shown:

LED CCT 6W/m 12W/m
color code 4000K F F
3500K F F
3000K F F
2700K F F
2500K F F
2200K F F
EQ 4000K F F
3000K G G
2700K G G
RGB N/A

For further help regarding installation visit lumino.lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals