SILENTAIRE 559061000 Plasma Air Disinfection Air Purifier User Guide
- June 10, 2024
- SILENTAIRE
Table of Contents
Product Information
The Plasma Air Disinfection Round 24 Purifier is a part of the SAP-PL-R24-MV- BK/SAP-PL-R24-MV-WH model series with model number 559061000/559061010. It is a fixture that weighs 35lbs and requires an installation height of above 10ft. The package contents include a fixture, chain, wire connector, mounting bracket, screw, side cover, and safety rope.
Product Usage Instructions
-
Select a suitable location that can support the weight of the fixture.
-
Determine the method of mounting before drilling.
-
Suspend Mounting
-
Punch out the knock out hole of the mounting bracket.
-
Install the mounting bracket and pass the wires through the
flexible pipe (1/2in or 3/4in, not included). -
Slide the mounting bracket into the fixture and fix the
mounting. -
Install three chains.
-
Make the electrical connections: Black color to black color.
White color to white color. Green color to green color. -
Fix the side cover.
-
Hang the safety rope to complete the installation.
-
-
Stem Mounting
-
Punch out the knock out hole of the mounting bracket.
-
Slide the mounting bracket into the fixture.
-
Fix the mounting bracket by screws and then connect wires:
Black color to black color. White color to white color. Green color
to green color. -
Fix the side cover.
-
Hang the safety rope to complete the installation.
-
-
To replace the Ozone net, check that the knob is tightened all
the way. If the fixture is not turning on, after replacing the
Ozone net, check the knob again. -
To clean the air inlet net, remove the Fixture Air Inlet Net
and clean it before replacing it.
For any questions, problems, or missing parts, contact ETiSSL Customer Service at 1-855-ETI-SSLI (1-855-384-7754) or visit www.ETiSSL.com from Monday to Friday, 8 a.m. to 5 p.m., CST.
USE AND CARE GUIDE
PLASMA AIR DISINFECTION ROUND 24” PURIFIER
NOTE: Keep your receipt and these instructions for proof of
purchase.Dispose used products according to local regulation.
WARNING: Shut off the power at the circuit breaker or fuse panel before
removing the old fixture, ballast, or fluorescent tubes. The installation
height must be above 10ft. Make sure the ceiling can withstand the weight of
this product at 35LBS.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
PACKAGE CONTENTS
INSTALLATION
Select a suitable location that can support the weight of the fixture.
Determine the method of mounting before drilling.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you
are working on is shut off. Either remove the fuse or turn off the circuit
breaker before removing the existing light fixture or installing the new one.
With power disconnected to your electrical box, remove the existing fixture.
Make a sketch of how the current fixture is wired (by wire color) or mark the
wires with masking tape and a pencil so you will know how to properly
reconnect the wires to the new LED light fixture.
RISK OF ELECTRIC SHOCK – These servicing instructions are for use by
qualified personnel only. To reduce the risk of electric shock, do not perform
any servicing other than that contained in the operating instructions unless
you are qualified to do so.
This product complies with the maximum allowable concentration of ozone of
0.050 parts per million by volume (ppmv) in a 24-h period.
Suspend Mounting (dimension of the chain is 31.5inch)
- Punch out the knock out hole of the mounting bracket. Install the mounting bracket. Pass the wires through the flexible pipe (1/2in or 3/4in, not included). Slide the mounting bracket into the fixture, and then fix the mounting.
- Install three chains.
- Make the electrical connections:
- Black color to black color.
- White color to white color.
- Green color to green color.
- Fix the side cover.
- Hang the safety rope, to complete the installation.
Stem Mounting Not Included (diameter of the stem is 1.1inch)
- Punch out the knock out hole of the mounting bracket. Slide the mounting bracket into the fixture.
- Fix the mounting bracket by screws and then connect wires.
- Black color to black color.
- White color to white color.
- Green color to green color.
- Fix the side cover.
- Hang the safety rope, to complete the installation.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
- Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45°C. SUITABLE FOR DAMP LOCATIONS. MINIMUM 90°C SUPPLY CONDUCTORS. CAUTION-RISK OF SHOCK. DISCONNECT POWER BEFORE SERVICING. • STORE IN AMBIENT NOT EXCEEDING 45°C.
FCC STATMENT
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. MAINTENANCE: See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. – 5
p.m., CST, Monday – Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>