COOLER MASTER Synk X Gaming Chair User Manual

: May 15, 2024
: COOLER MASTER

COOLER MASTER Synk X Gaming Chair

COOLER-MASTER-Synk-X-Gaming-Chair-PRODUCT

Product Information

Specifications

Product Name: Synk X
Voltage: 100~240VAC 50/60Hz
Power: 100W Peak/50W RMS, 4, 2 sets of transducer
Structural Materials: Shock-absorbing plywood, Metal pipes
Seat Materials: Flame-resistant foam and three-layer breathable mesh, Goose down fabric
Size: Length: 683 mm,
Width: 726 mm,
Height: 1225 mm
Weight: 29.4 kg
Operating Temperature:
Operating Humidity:
Weight Capacity:
- Seat Weight Capacity: Maximum weight 136 kg
- Reclined backrest weight capacity: Maximum weight 96 kg
Battery Specifications: 4S2P Lithium-ion battery pack 16.8V 5200mAh

Specifications

Product Name	Synk X
Voltage	100~240VAC 50/60Hz
Power	**** 100W Peak/50W RMS, 4Ω, 2 sets of transducer
Structural Materials	Shock-absorbing plywood, Metal pipes
Seat Materials	Flame-resistant foam and three-layer breathable mesh,

Reclined backrest weight capacity: Maximum weight 96 kg

**Battery Specifications**| 4S2P Lithium-ion battery pack 16.8V 5200mAh

ACCESSORY NAMES AND FUNCTIONS

COOLER-MASTER-Synk-X-Gaming-Chair-FIG-1

Caution!

The weight capacity of the seat is 136 kg
The weight capacity of the backrest is 96 kg

Caution!

The weight capacity of the 4D armrest pad is 23 kg
The weight capacity of the leg rest is 30 kg

CONTROL PANEL AND FUNCTIONS

COOLER-MASTER-Synk-X-Gaming-Chair-FIG-3

LIST OF COMPONENTS

COOLER-MASTER-Synk-X-Gaming-Chair-FIG-4

PRESSURE CASTER WHEEL INSTALLATION

Take the five pressure caster wheels and insert them into the holes in the base

GAS CYLINDER INSTALLATION

Take the Gas Cylinder and insert it into the hole located at the center of the base

SEAT AND BACKREST INSTALLATION

Lay the backrest flat on the floor and insert the seat into the tilt structure
Take the 20 mm screws, insert them, and tighten them with the M5 hex wrench

4D ARMREST INSTALLATION

Place the left and right armrests in the holes on both sides of the base of the seat
Take the 25 mm screws, insert them, and tighten them with the M5 hex wrench

CABLE CONNECTIONS

COOLER-MASTER-Synk-X-Gaming-Chair-FIG-13

Connect the DC plug to the corresponding socket
Connect the DuPont connector to the corresponding DuPont socket

CHAIR ASSEMBLY

Align the gas cylinder with the hole in the center of the seat and press the seat into place

RECLINING ANGLE ADJUSTMENT

The maximum angle the backrest can recline is 135°

SEAT HEIGHT ADJUSTMENT

Seat Height Adjustment Lever

Push the lever down to lock the seat height
Pull the lever up to unlock the seat height

The adjustment range of the height is 46 to 55 cm

LEG REST ADJUSTMENT

Leg Rest Strap
Two-level length adjustment
The leg rest can be extended to a maximum of 36 cm

4D ARMREST ADJUSTMENT

The extension range of the armrest is 90 mm
The armrest pad can be rotated to the left or right by 35°
The left/right lateral sliding distance of the armrest pad is 25 mm
The front/back sliding distance of the armrest pad is 50 mm

ARGB LED CONTROL

Mode 1: Uniform red light
Mode 2: Uniform purple light
Mode 3: Uniform green light
Mode 4: Uniform blue light
Mode 5: Rainbow flow effect
Mode 6: Rainbow breathing effect
Mode 7: Off
When powered on, the system automatically remembers the ARGB illumination mode chosen when the system was last turned off

INTERFACE INPUT CONTROL

COOLER-MASTER-Synk-X-Gaming-Chair-FIG-30

HEADPHONE VOLUME AND VIBRATION LEVEL CONTROL

Headphone volume adjustment: Adjusts the volume in real-time
Vibration level adjustment: Adjusts the vibration level in real time

POWER OPERATIONS

Caution!

The Synk X system is powered by lithium-ion batteries, which are built into the chair.
Before using the system for the first time, please ensure that the lithium-ion battery pack is fully charged and properly connected. Only use the factory-certified DC19V power adapter that came with the chair.
The battery status indicator will be red when the battery is charging and goes out when the battery is fully charged.
The Synk X system can be used while charging. The vibration level will be reduced when the battery is below 30%.
The battery pack can be charged at any time; a full discharge is not required before charging. Keeping the battery fully charged and using it regularly will increase its performance and life cycles.
Caution: Avoid repeatedly discharging the battery completely, as it will cause the battery pack to age rapidly.

IMPORTANT SAFETY INFORMATION

Do not sit on the backrest, legrest, and armrests.
Place the chair on a level surface to prevent accidents or injuries.
Do not place any objects or body parts into any gaps in the chair.
To prevent accidents or injuries, do not crawl under the leg rest.
Keep sharp objects away from the surface of the chair.
Do not use the chair in damp environments.
Do not touch any plugs, sockets, switches, and wires that are powered with damp hands.
Do not sit in the chair simultaneously with another person.
Do not exceed the rated power during power operations.
Do not exceed the weight capacity of the chair.
Avoid excessively tilting the backrest and causing the wheels to rise beyond the proper range of motion.
Do not stand on the armrests or apply excessive force and pressure to them.
To prevent falls, do not stand on the seat, backrest, or legrest.
Do not place the chair in direct sunlight, as it could cause the chair to fade, deteriorate, or crack.
Apply appropriate force when moving the chair, and move it slowly.
Apply appropriate force when raising or lowering the seat, as excessive force could break and damage the gas cylinder.
Please keep the pressure caster wheels clean, as dust or other foreign objects could make the ground dirty or jam the wheels.
The pressure caster wheels may damage softer floors; floor mats are recommended in this case.
The seat may generate static electricity in dry weather or environments.
Do not place the chair near flames or lit cigarettes.
For safety reasons, do not play around while sitting in the seat.
Do not use the chair as a means of transportation; doing so may damage the chair and related property.
After assembling the chair, please make sure it is stable.
- Gently rock the chair to make sure it is level with the ground and that the screws are tight.
Please be patient when assembling the chair.
- Make sure each component is in the correct place.
Do not use or store the chair in high temperatures.
To prevent damaging the batteries or battery explosions, do not expose the control system to extreme temperatures or place it near sources of heat or flames.
Clean the control system with a soft and dry cloth only.
Do not drag the seat around while sitting in it; doing so may damage the braking effect of the pressure caster wheels.
To prevent wireless interference or poor reception, do not store or use the system near magnetic devices.
Only use the voltage specified by the chair’s power adapter. Using a higher voltage than required will damage the control system and may cause a fire or electric shock.
CAUTION Risk of fire or explosion if the battery is replaced by an incorrect type.
Do not ingest battery, Chemical Burn Hazard [The battery pack supplied with Synk X] This product contains a Lithium-ion battery. If the Lithium-ion battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

FREQUENTLY ASKED QUESTIONS

Question 1: How much space is needed?
- Answer: Please reserve enough space (at least 1.5 square meters) to safely tilt the seat back and extend the leg rest.
Question 2: Can I remove, repair, and reassemble the control system by myself?
- Answer: Please contact your local service provider for repairs.
Question 3: Can I replace the lithium-ion battery pack by myself?
- Answer: Only use certified battery packs made by the original manufacturer and strictly follow the battery specifications in this manual.
Question 4: How do I maintain the pressure caster wheels?
- Answer: Wipe them with water or detergent regularly or when they are dirty.
Question 5: How do I maintain the 4D armrest pads?
- Answer: Wipe them with water or detergent regularly or when they are dirty.
Question 6: How do I maintain the surface of the seat?
- Answer: Wipe them with water or detergent regularly or when they are dirty.
Question 7: How should I adjust the volume or vibration level when it is too low?
- Answer: Increase the output volume of the audio output device. If the device is a mobile phone or tablet, set the volume level to the maximum and use Synk X’s control interface to adjust the headphone volume and vibration level.
Question 8: The system’s indicators are normal and the headphone output is normal, but the vibration has stopped. How do I adjust it?
- Answer: Synk X may have entered protection mode due to overheating. Restart the system and reduce the vibration level.
Question 9: What are the contents of the warranty?
- Answer: Please visit www.coolermaster.com for the terms of the warranty.
Question 10: Which accessories are not covered by the warranty?
- Answer: The warranty covers all accessories except for consumables such as the pressure caster wheels, 4D armrest pads, and charging cables.

TROUBLESHOOTING

If the chair doesn’t respond when you press the buttons on the control interface located on the right side of the seat, please follow the steps below:
- A. Check whether the battery status indicator is lit
- B. Check whether the interface inputs have been connected successfully
- C. Check whether the headphone volume/vibration level knob is normal
- D. If the problem is not solved after you have completed the above steps, please press the power button again
If the chair cannot be adjusted, please follow the steps below:
- A. Check the tilt structure for foreign objects or damage
- B. Check the leg rest rail for foreign objects or damage
- C. Check the gas cylinder for foreign objects or damage
- D. Check the 4D armrest pad structure for foreign objects or damage
If the ARGB illumination mode cannot be adjusted, please follow the steps below:
- A. Check whether the battery status indicator is lit
- B. Check whether the ARGB illumination mode button is operating normally
- C. If the problem is not solved after you have completed the above steps, please press the power button again
If you cannot slide the chair, please follow the steps below:
- A. Check whether there are foreign objects on the ground
- B. Check whether the pressure caster wheels are installed correctly or damaged
- C. When the direction of the pressure caster wheels is inconsistent, more force is needed to move the chair or slide it to the left and right first to make it slide smoothly
If abnormal noise that’s not caused by vibration is emanating from the chair, please follow the steps below:
- A. Make sure the screws are secured correctly
- B. Check if the vibrator is working
- C. If the problem is not solved after you have completed the above steps, please contact customer service
If Synk X is not listed as a Bluetooth device name on the audio output device, please follow the steps below:
- A. Check whether the host is in Bluetooth mode
- B. Check whether Bluetooth is connected to another audio output device
- C. Disable Bluetooth on the audio output device and then enable it to search for devices
- D. Turn off the Synk X host and then turn it back on; make sure Synk X has entered into Bluetooth mode and is waiting to pair
If Synk X shuts down without warning, please follow the steps below:
- A. Check whether the battery is too low or completely drained
- B. Synk X may have activated battery protection mode due to overcurrent and shutdown.
- In this case, charge it with the power adapter for about one minute and then turn it back on If the problem is not solved after you have completed the above steps, please contact customer service

FCC REGULATORY STATEMENTS

United States FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

Un-license band: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

this device may not cause harmful interference,
this device must accept any interference received, including interference that may cause undesired operation.

(15.21) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.

Canada Canada, ISED notice:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Innovation, Science, and Economic Development Canada radio frequency exposure limits. The Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).

Europe(CE)

Hereby, [Cooler Master Inc.], declares that this [Haptic Chair] complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.
URL: www.coolermaster.com

United Kingdom

Hereby, [Cooler Master Inc., declares that this [Haptic Chair] complies with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
URL: www.coolermaster.com