LUMINO HXA1-MA005 LED Light Installation Guide

June 6, 2024
LUMINO

LUMINO HXA1-MA005 LED Light

LUMINO-HXA1-MA005-LED-Light-image

Installers must read this document and any other referenced documents in full before commencing installation work. Failure to observe all installation guidance in this document may result in unsafe installation, cause permanent product damage and void product warranty. This document is subject to change without notice. Check for latest documentation with LUMINO. Copyright © LUMINO. E&OE.

HANDLING PRECAUTIONS

LED PROFILE

To avoid permanent damage, do not allow small or sharp objects to apply pressure on to any part of the LED tape.

STRESS

Never stand or place weighted items on the product. The product is not vandal resistant and has no IK rating. Do not subject the product to impact forces.

POWER CABLES

The product end caps, power cables and connectors must not be pulled or twisted. Never pull the product by its power cables or hang it from its power cables or connectors.

CUTTING AND SAWING

The product must not be sawn, drilled or otherwise modified in any way.

DAMAGES

Inspect the product. If you see any damage upon unpacking, report to LUMINOX immediately and do not install the product.

LOCATION

Suitable for wet locations. IP67 rated for temporary submersion for no more than 30mins. Ensure there is adequate drainage made available for the product. Protect product from dust, paint and harmful substances during installation and use. Ensure the product is not exposed to VOC gases. Do not obstruct the product and its light output.

SAFETY GUIDANCE

  1. LED MODULE
    The product is classed as a built-in, non-integrated LED module and therefore must be mounted into an enclosure, box, luminaire or the like. Do not use the product mounted directly to a wall, ceiling or other surface without some kind of enclosure.

  2. WIRING GUIDE
    Follow the guidance shown in the provided wiring guide, including maximum cable lengths, cable sizes and other wiring instructions. When running cables through an enclosure, ensure cables are protected from damage, separated from mains voltage cables and anchored against being pulled. Make connections appropriate for the IP rating of the product.

  3. QUALIFIED INSTALLER
    Installation must be carried out by a qualified person and conducted in accordance with local regulations and applicable standards.

  4. THERMAL MANAGEMENT
    Ensre ambient temperature (Ta) does not exceed 25°C (77°F) and case temperature (Tc) does not exceed 70°C (158°F). Exceeding max Tc will cause permanent damage and void the product warranty. Allow sufficient clear air space for the LED drivers, and suitable access to the drivers as specified on installation instructions.

  5. REPAIR AND REPLACEMENT
    If the product is not functioning, contact LUMINO to register a Service Call for factory repair or replacement. Light source is not user replaceable. See page 5 for Ecodesign and end of life information.

DRIVERS

  1. POWER OFF
    Product and driver must not be live wired. Switch off power before work begins. Follow instructions and guidance for the make and model of driver being used.

  2. 24VDC SELV
    Only use drivers with a maximum output of 24VDC. Drivers must be SELV, constant voltage with both overload and short-circuit protection.

  3. DIMMERS
    Check dimmer is compatible with the driver and certified to local regulations.

  4. INRUSH CURRENT
    Many constant voltage LED drivers can have high inrush current at power-on. Driver’s inrush current can be many times the normal operating current. Use a suitable MCB. Type C MCBs are normally suitable but if inrush current is a persistent problem an inrush suppressor may be required.

  5. PROTECTION
    Use only with 24VDC Class 2 power unit to UL1310 standard with overload and short-circuit protection. Rate drivers for at least 10% above load. Driver protection circuitry must not be relied upon to protect secondary 24VDC electrical circuits from damage caused by over-current or short circuit. DC fuses or DC electronic circuit breakers are recommended for full protection. Allow for access to drivers for maintenance and sufficient clear air space for ventilation.

  6. CABLING
    Do not overload the driver. Damage will be caused by incorrect input voltage, reverse polarity or short circuit. Plan for loads, driver locations, dimming and cabling prior to start of work. Ensure basic insulation is maintained between mains and dimming control wires.

IMPORTANT

LUMINO-HXA1-MA005-LED-Light-fig-1

  • TURN POWER OFF!
  • CHECK THE WALL
  • SIDE-TO-SIDE BENDING ONLY
  • DO NOT TWISTLUMINO-HXA1-MA005-LED-Light-fig-2
  • DO NOT PULL LED PROFILE
  • DO NOT PULL CABLE
  • DO NOT APPLY PRESSURE OR WEIGHT
  • DO NOT HAMMER OR SAW
  • BENDING BREAKS CIRCUIT! MIN BEND RADIUS Ø100MM
  • Over bending may cause damage. Support the product during installation (two people recommended) to avoid it over bending under its own weight. Do not power on the product while coiled up or while wound onto a reel.
  • The product must not be cut, sawn or torn in any way. Even small cuts or tears in the silicone rubber can become larger if stressed and result in a failure of the IP rating. If you see any such damage upon unpacking or during installation report this to LUMINO immediately and do not install the product.

ACCESSORIES

  1. Cable & Connector HXA1-PC IP67 power link 300mm / 1000mm cable
  2. Recessed Plaster-in Channel HXA1-MA005 White channel 2 metres
  3. Surface Channel HXA1-MA006 White channel 2 meters
  4. Surface Clip HXA1-MA521-R1 20pcs White clips Allow 4 clips per metre

INSTALLATION

Plan Installation

Check product and its dimensions against the planned installation. Runs of LEDs may have to be installed in a particular sequence.

Prepare Power Supply

This product requires a 24VDC power supply. Please refer to provided wiring guide document. Failure to follow guide may result in damage to the product and voiding of the warranty.

Skip ahead to the relevant fixing option.

SURFACE CLIPS

HXA1-MA521-R1

Cable Exit

Plan cable entry and exit points before installing the product. Make a suitably sized hole for the cable/s to pass through, and position beneath where the product is planned to be placed.

Mount Clips

Fix all the clips securely to the mounting surface. Recommended screw size is a Ø3.5mm / Nº 6 gauge screws. If necessary, use alternative fixings of a similar gauge and size suitable for the material being fixed into. Products should be held by at least 4 equally spaced clips per metre. Clips spaced no more than 500mm apart. IMHXA_R2201.

Connect to LED Driver
With the power off. Feed the power cables to the alpha helix, connecting the product to the LED driver. Finalize all electrical connections and test the circuit. If the product does not function as expected, turn power off immediately and check all connections.

Install into Surface Clips

Align clips and carefully push the product into the clips. Ensure the product is fully clipped in place and check it is not misaligned or misplaced due to screw heads or wires. Ensure that cables are not pinched when installed.

SURFACE CHANNEL

HXA1-MA006

Drill Holes

Drill 5mm holes on the centre line, spacing them no more than 500mm apart. Plan for cable entry and exit points.

Mount Channel

Fix channel securely to the mounting surface. Recommended screw size is a Ø3.5mm / Nº 6 gauge screws. If necessary, use alternative fixings of a similar gauge and size suitable for the material being fixed into.

Connect to LED Driver

With the power off. Feed the power cables to the alpha helix, connecting the product to the LED driver. Finalize all electrical connections and test the circuit. If the product does not function as expected, turn the power off immediately and check all connections.

Silicone Channel & Install

Apply two small bead lines of silicone sealant inside the channel before pushing the alpha helix to bond in place.

For further help regarding installation visit lumino. lighting

RECESSED PLASTER-IN CHANNEL HXA1-MA005

Cut-out Requirements

Saw cut-out using dimensions below. The surface thickness of 12.5mm MIN and be able to support both the weight of the product and channel.

Install Channel

With cables out, insert the profile into the cut-out.

Mounting Holes

Drill 5mm holes on the centre line, spacing them no more than 500mm apart.

Fix Channel to Surface

Securely fix channel to the mounting surface. Recommended plasterboard/drywall screws size of Ø3.5mm, or gauge Nº6.

Plaster

Finish any surface preparation and skim mounting surface in plaster, taking care not to get any plaster in the channel.

Connect to LED Driver

With the power off. Feed the power cables to the alpha helix, connecting the product to the LED driver. Finalize all electrical connections and test the circuit. If the product does not function as expected, turn the power off immediately and check all connections.

Silicone Channel & Install

Apply two small bead lines of silicone sealant inside the channel before pushing the alpha helix to bond in place.

LED MODULE

This product is classed as a built-in, non-integrated LED module in accordance with the LED Modules for General Lighting standards
BS EN 62031:2008, AMD1:2012, AMD2:2014, AMD2:2015 and BS EN 62031:2020. Therefore, it must be mounted into an enclosure, box, luminaire or the like. Do not use the product mounted directly to a wall, ceiling or another surface without some kind of enclosure.

ECODESIGN REGULATION

This product is considered to be a “containing product” in the sense of Regulations (EU) 2019/2020 and (EU) 2019/2015. The contained light source is an integrated part of the containing product and its removal can only be done by causing permanent damage to the containing product. Therefore, replacement of the light source with the use of commonly available tools is not justified due to its restricted mechanical, electrical, optical, thermal, and/or environmental protection requirements.

DISMANTLING

Dismantling of light source from the containing product at end of life: The containing product shall be cut to the length of the contained light source and the light source mechanically detached from the containing product. Containing product component parts shall then be disassembled. Containing products shall be separated from building material and/or from other additional mounting accessories by means of a professional installer. Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. LUMINO is a member of the WEEE producer complaince scheme. Registration number: WEE/MM8138AA.

ENERGY RATING

This product is a light source of energy efficiency

classes as shown:

LED CCT 6W/m 12W/m

EQ

| 4000K| F| F
3000K| G| G
2700K| G| G

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals