Parrot Uncle F8270110V 12.5 in Brown Low Profile Flush Mount Cage Ceiling Fan Instruction Manual

Parrot Uncle F8270110V 12.5 in Brown Low Profile Flush Mount Cage Ceiling

Fan

F8270110V
Operating Instructions for the Parrot uncle Owner’s Installation, Manual

WARNING: SHUT POWER OF F AT FUSE OR CIRCUIT BREAKER

Sicherheit information

1. To reduce the risk of an electrical blow, electricity on the protective switch or the safety box went out before starting.

2. All wiring must correspond to the NASI/NFPA 70-1999 National Electric Code and local electrical regulations. The electrical installation must be carried out by a qualified and approved electrician.

3. The connection box and support construction must be assembled safely and 35 pounds (15.9 kilos) must be able to transport reliably. Use only output boxes listed with labeling
   “Accepted for fans with a weight of£ 35 (15.9 kilos) or less.”

4. The fan must be installed with a minimum distance of 2.1 m (7 feet) from the posterior edge of the wings to the floor.

5. Do not operate the reverse switch If the fan wings are moving. You have to tum off the fan and stop the wings before reverse the direction of the wing.

6. Do not place objects on the road to wings.

7. To avoid lesions or damage to the fan and other objects, be careful if you work on the fan or dean it.

8. Electrical diagrams only serve as a reference. The lighting rates that are not delivered with the fan must be listed and marked with the valve model that will be installed for use. The switches must be general use switches UL. Take into account the Instructions for the appropriate Installation included in the lighting rates and the switches.

9. After the electrical connections have been made, the size staircase must be turned up and carefully push to the plug box. The cables must be distributed in such a way that the ground connected driver and the device head are next to the socket.

All fixing screws must be verified before installation and, if necessary, followed.

• WARNING: To reduce the risk of injury, knife supports (also known as flanges) cannot be folded during Installation or after Installation. Do not put any object on the path of wings.
• WARNING: Remove rubber motor attacks at the bottom of the fan before mounting the wings or try the engine.
• WARNING: To avoid the risk of a fire or an electrical blow, this fan should not be used with a semiconductor speed controller.
• WARNING: To avoid a possible electric shock, tin off the current In the main security box before wiring. If you feel that you do not have enough knowledge or experience In electrical wiring, communicate with a license electrician.
• WARNING: Electrical diagrams only serve as a reference. The optional use of an lighting rate must be on the list and marked with this fan for use.
• WARNING: To reduce the risk of fires, electrical discharges or Injuries, assemble the device in a socket that with the Inscription accepted for fans with a weight of£ 35) or less. It 1s marked and use the screws supplied with the plug.

TCHNICAL INFORMATION

|
---|---
SKU| Nominal voltage| Nominal output (motor)| light
F8270110V| 110-120V  AC| 15W| 3*G9 MAX. 2W

Pls check whether above accessories are completed or not Yes, and install.

Installation

1. Take the finished F8270 out of the packing box and loosen the two screws
2. on the opposite side of the disk plate, and the other “L” hole diagonal screw
3. only half (no need to loosen completely).

INSTALLING THE FAN :

Tools Required: Phillips screwdriver, pair of paler, straight a lot screw driver, ad/unstable wrench, step ladder, and wire cutlers.

Installing The Mounting Bracket
The Colling fun must be installed In a location so that the blades are 12°(300mm) spacing from the tip of the bade to the nearest objects or wall. When hanging the Fun REMEMBER to turn off the pioneer. Follow the Instruction below to hang your an property:

1. For wood ceiling, Secure the mounting bracket to the ceiling is capable of carrying a load of at least 100 be (45kgs) with two long mounting across and washers provided. Be sure at least 0. 12(310mm) of the Bore Is threaded Into the support.
2. For Installing to outlet box, secure the outlet box directly to the building structure. Use appropriate fasteners and bulling materials. The outlet box and Its support must be able to fully support the moving weight of the fan(at least 100lbs). Use a UL Elated meatal outlet box. Do not use a planktic boletes box. Figure 1& 2 examples to mount the outlet box.
3. Hook the product into the fixed “L” hook of the disk plate,
4. According to the wiring diagram, plug the input end of the motor and the output end of the remote control well, the input blue and white line of the product and the output line of the remote control, and the input line of the remote control and the external Neutral Live wire.
5. Take the fan product out of the hook, align the “L” shaped hole with the screw that has been loosened in half before, and put it on the top of the circular lift plate, and then turn it to the right, so that the fan is hooked on the lift plate
6. Hook the product into the fixed “L” hook of the disk plate
7. Tighten screws 1 and 2
8. The product installation is complete

Operating Instructions

Install remote control

1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
2. Push that canopy ring to the bottom of the canopy, allude the Inner holes aligned to the two prominent crowed on the mounting bracket again, and tum the canopy ring clockwise until tight.

remote control

Preparing for mounting

1. Remove the mounting bracket from the canopy by loosening the two canopy screws located In the L shaped slots.
2. Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket

LIGHT MUST BE KEPT AT THE ON POSITION
FAN MUST BE KEPT AT THE HIGH SPEED

Remote controller

GENERAL INFORMATION

• This remote controller is designed to separately control your ceiling fan speed and light on and off. There are four buttons(Limed, Low, OFF) to control the speed of the fan and off
• The light button will control the light on and off.
• The red indicator on the transmitter will light when one of the five buttons is pressed.

INSTRUCTION OF INSTALLATIONAND OPERATION

SETTING THE CODES
To set the codes, perform the following steps:

• Setting the codes on the transmitter:
  • Remove battery cover.Press firmly on the arrow and slide battery cover off.
  • Slide code switches to your choice of up or down position.(Factory setting is all up. Do not use this position.Use a Small screwdriver or ball point pen to slide firmly up or down (Figure 1)).
• Setting the codes on the receiver:
  • The Learn Key must be pressed with in 30 seconds, after pressing the Power button.
  • If not, please press the Power button to restart.
  • Keep pressing the button learn key in excess of 3 second it becomes a LEARN status.
  • The receiver can remember the last codes status. The light flash two times.

INSTALLJNG RECEIVER IN CEILING FAN

1. Safety precautions:
2. WARNING: HIGH VOLTAGE! Disconnect power by removing fuse or switching off circuit breaker.
3. Do not use with solid state fans.
4. Electrical wire must meet all local and national electrical code requirements.
5. Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0,Maximum light watts: 180 incandescent or ballast and LED.
6. Otherwise power can cause serious injury or death.
7. installing receiver in fan:
8. Remove power from the circuit.
9. Remove ceiling fan canopy from the mounting bracket.
10. Disconnect existing wiring between ceiling fan and Supply in electrical junction box.
11. Make connections as follows, using the wire nuts supplied:

OPERATING TRANSMITTER:

1. Install CR2025 volt battery. (To prevent dam age to transmitter, removal the battery if not used for a long time).
2.  Store the transmitter away from excessive heat or humidity.
3. Operating the buttons on the panel of the transmitter.
4. Setting the codes on the receiver:
5. Code matching key : The operation is as follows: press this key to code matching within 5 seconds alter the fan lamp Is powered on. If the code matching Is successful, the fan will make a “drop” sound; If not, repeat the action.

size of product

AFTER INSTALLATION

WOBBLE”

• The fan blades have been adjusted in the factory to minimize any wobble
• NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED
• RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
• TO REDUCE THE FAN WO BBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING

BRACKET AND DOWN ROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:

1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the
   blades. Measure this distance.Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1 /8″ ( 0. 32c m).

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight  and possibly result in smoother operation.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time.

CARE AND CLEANING

1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or Lint free cloth to avoid scratching the paint finish. Please make sure to turn 018] electricity power before you clean your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil
   NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>