SuperLightingLED L1(WZ) 0/1-10V ZigBee + RF + Push Dimmer Instruction Manual
- June 5, 2024
- SuperLightingLED
Table of Contents
SuperLightingLED L1(WZ) 0/1-10V ZigBee + RF + Push Dimmer
0/1-10V ZigBee + RF + Push Dimmer
Model No.: L1(WZ)
Tuya APP cloud control/Voice control/RF dimming/Push Dim/0-10V or 1-10V/Wall
junction box mounting
Features
- ZigBee + RF + AC push 0/1-10V dimmer, 1 channel output.
- Output 1 channel 0/1-10V signal, connect with 0/1-10V dimmable driver.
- Tuya APP cloud control, support on/off, brightness adjust, delay turn on/off light, timer run, scene function.
- Voice control, support amazon ECHO and TmallGenie smart speaker.
- 0-10V or 1-10V output selectable by DIP switch.
- 256 levels 0-100% dimming smoothly without any flash.
- Compatibility with RF 2.4G single zone or multiple zone dimming remote control.
- Each L1(WZ) controller can also work as ZigBee-RF converter, then use Tuya APP to control one or more RF dimming LED controller or driver synchronously.
- Connect with external push switch to achieve on/off and 0-100% dimming function.
- Easy to be placed in standard wall junction box behind a push switch.
Technical Parameters
Input and Output
Input voltage| AC100-240V
Output signal| 0/1-10V (20mA)
Safety and EMC
EMC standard (EMC)
| EN 55015:2013
EN 61547:2009
EN 61000-3-2:2014
EN 61000-3-3:2013
Safety standard(LVD)
| EN 61347-2-11:2002
EN 61347-1:2015
EN 62493:2015
Certification| CE,EMC,LVD
Dimming data
Input signal| Tuya APP + RF + Push Dim
RF Control distance| 30m(Barrier-free space)
Dimming level| 256 levels
Dimming range| 0 -100%
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| T c: +65OC
IP rating| IP20
Mechanical Structures and Installations
System wiring
Note:
-
The above distance is measured in spacious(no obstacle) environment,
Please refer to the actual test distance before installation. -
Users must use the Tuya ZigBee gateway to realize remote control and voice control.
Wiring diagram
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
Tuya APP network connection and operation
- Press and hold the Match/Set key for 2s, reset the ZigBee network.
- Press and hold the Match/Set key for 5s, or push twice the Match/Set key fastly,
- Clear previous network connection, enter config mode. the blue LED indicator fast flash.
- If the Tuya APP network connection succeeds, the blue LED indicator will stop flash, and in Tuya APP, you can find the SKYDANCE-ZB-DIM device.
- Tuya APP interface operation: Touch the brightness slide to adjust brightness.
0-10V or 1-10V dimming setting
Select 0-10V dimmer or 1-10V dimmer according to the dimmable LED driver.
L1(WZ) match RF remote control (Optional)
End-user can choose the suitable match/delete ways. Two options are offered
for selection:
Use the L1(WZ)’s Match key
Match:
Short press the match key of L1(WZ), immediately press on/off key (single-zone
remote) or zone key (multiple zone remote) on the remote.
Delete:
Press and hold the match key of L1(WZ) for 10s to delete all matches, The
light blinks 5 times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power of L1(WZ), then switch on power again, immediately short
press on/off key (single-zone remote) or zone key (multiple zones remote) 3
times on the remote. The light blinks 3 times means match is successful.
Delete:
Switch off the power of L1(WZ), then switch on power again, immediately short
press on/off key (single-zone remote) or zone key (multiple zones remote) 5
times on the remote. The light blinks 5 times means all matched remotes were
deleted.
L1(WZ) work as a ZigBee-RF converter to match other RF dimming LED controller or driver
End-user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press the match key of the controller, immediately press on/off key on
the Tuya APP. The LED indicator fast flash a few times means the match is
successful.
Delete:
Press and hold the match key of the controller for 5s, The LED indicator fast
flash a few times means the match was deleted.
Use Power Restart
Match:
Switch off the power of the controller, then switch on power again,
immediately short press on/off key 3 times on the Tuya APP. The light blinks 3
times means match is successful.
Delete:
Switch off the power of the controller, then switch on power again,
immediately short press on/off key 5 times on the Tuya APP. The light blinks 5
times means match was deleted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>