SuperLightingLED LF-150-24 0/1-10V Constant Voltage LED Driver Instructions
- June 5, 2024
- SuperLightingLED
Table of Contents
LED LF-150-24 0/1-10V Constant Voltage LED Driver
Instruction Manual
Features
- Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
- Universal AC input / Full range
- 1 channel constant voltage output, Max. total output power 150W
- Built-in active PFC function: 0.95 Typ
- Synchronize on multiple LED drivers
- Over-heat / Over-load / Short circuit protection, recover automatically
- Suitable for indoor LED lighting application
- 5 Year, 50,000hr warranty
Mechanical Structures and Installations
Technical Parameters
| Model | LF-150-12 | LF-150-24 |
|---|---|---|
| Output | Output Voltage | I 2vix. |
| Output Current | Max. 12.5A | Max. 6.25A |
| Output Power | Max. 150W | |
| Startup time | 2S/ 115VAC, I S/230VAC | |
| Dimming Range | 0-400% | |
| Ripple & Noise | <=150mV/230VAC | |
| PVVM Frequency | 2000Hz | |
| Input | Input Voltage Range | 100–240VAC |
| Frequency Range | 50/601-1z | |
| Efficiency | 92%/230VAC | |
| Alternating Current | 1.5A/115VAC, 0.75A/230VAC | |
| Power Factor | >0.95/230VAC | |
| THD | <5%/100VAC, <10%/230VAC@ half loud | |
| Inrush Current | Cold start 71 A at 230VAC | |
| Anti Surge | L.N:IKV:I.,N.FG:2kv | |
| leakage Current | <5mA | |
| No Load Power | 2W/115VAC, 2W/230VAC | |
| Protection | Over Load Power | Shut down the output when current load >= |
110%–140%, auto recovers.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers.
Over Temperature| Intelligently adjust or turn off the output current if the
PCB temp > 100t, auto recovers.
Environment| Woking Temperature| -30°C–50°C
Tcase Max| 80t
Working Humidity| 20%–90%RH, non-condensing
Storage Temperature/Humidity| -40t–’80°C, 10%–95%RH
Temperature Coefficient| ±0.03%/t (0.50%)
Vibration Resistance| 10.500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20
Sofety &EMC| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| 1/P.O/P: 3750VAC
Insulation Resistance| I/P.O/P: 100MQ/500VDC/25°C/70%RH
EMC Emission| EN55015, EN6100032 Class C, IEC610003.3
EMC Immunity| EN610004.2.3.4.5.6.8.11, EN61547
Certifications| CE, EMC
Applications
- Suitable for LED-related fixtures or appliances which use LED light bars and LED tope (like LED Decoration or Advertisement devices).
- Office / Commercial / Domestic Lighting, Hotels, Retail, and Display.
- Use for retrofit upgrades & new luminaire designs.
Wiring Diagram
0/1-10V Connection
- The 0/1-10V input is operable via commercially available simple rotary wall switches designed for 0/1-10V dimming equipment or from dedicated system central dimming controllers.
- Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
- We recommend the number of LED drivers connected to the 0/1-10V dimmer does not exceed 50 pieces, The maximum length of the wires from the dimmer to the LED driver should be no more than 50 meters.
- If the LED driver is used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface, the 0/1-10 V signal should change over 10% to return 0/1-10 V control.
AC Push-Dim connection
The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.
-
Short press:
Turn on or off the light. -
Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes in the opposite direction. -
Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure. -
Synchronization:
If more than one LED driver is connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from the push to the LED driver should be no more than 20 meters.
Dimming Curve
