SuperLightingLED DL 4 Channels 0-1-10V DMX512 Decoder Instruction Manual
- June 2, 2024
- SuperLightingLED
Table of Contents
4 Channels 0/1-10V DMX512 Decoder
Model No.: DL
RDM/Stand-alone function/Linear or logarithmic dimming/Numeric display/Din
Rail
Features
-
Comply with the DMX512 standard protocols.
-
Digital numueric dispaly, set DMX decode start address by buttons.
-
RDM function can realize intercommunication between
DMX master and decoder. For example,
DMX decoder address can be set by DMX master console. -
1/2/4 DMX channel output selectable.
-
0-10V or 1-10V output selectable.
-
Logarithmic or linear dimming curve selectable.
-
Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal.
-
Available in white or black.
Technical Parameters
Input and Output
Input voltage| 12-24VDC
Input signal| DMX512
Output signal| 0/1-10V analog
Output current| 4CH,20mA/CH
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Certification| CE,EMC,LVD
Environment
Operation temperature| Ta: -30 O C ~ +55 O C
Case temperature (Max.)| T c: +65 O C
IP rating| IP20
Warranty and Protection
Warranty| 5 years
Protection| Reverse Polarity
Weight
Gross weight| 0.102kg
Net weight| 0.132kg
Mechanical Structures and Installations
Wiring Diagram
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer (each channel) does not exceed 20 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 30 meters.
Operation
System parameter setting
-
Long press M and ◀ key for 2s, prepare for setup system parameter: decode mode, 0/1-10V output, output brightness curve, default output level, automatic blank screen. short press M key to switch
-
Decode mode: short press ◀ or ▶ key to switch one-channel decode(“d-1”), two-channel decode(“d-2”)
or four-channel decode(“d-4”).When set as 1 channel decode, the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address. -
0/1-10V output: short press ◀ or ▶ key to switch 0-10V(“0-0”) or 1-10V(“1-0”).
-
Output brightness curve: short press ◀ or ▶ key to switch linear curve(“C-L”) or logarithmic curve(“C-E”).
-
Default output level: press or key to change default 0-100% level ( d00 to dFF ) when no DMX input signal. ◀ ▶ ” ” ” “
-
Automatic blank screen: short press ◀ or ▶ key to switch enable (“bon”) or disable(“boF”) automatic blank screen.
-
Long press M key for 2s or timeout 10s, quit system parameter setting.
DMX mode
- Short press M key, when display 001~512, enter DMX mode.
- Press ◀ or ▶ key to change DMX decode address(001~512) , long press for fast adjustment.
- If there is a DMX signal input, will enter DMX mode automatically.
- DMX Dimming: Each DL DMX decoder occupy 4 DMX address when connecting the DMX console.
For example, the defaulted start address is 1, their corresponding relationship in the form:
DMX Console | DMX Decoder Output |
---|---|
CH1 0-255 | CH1 0-10V |
CH2 0-255 | CH2 0-10V |
CH3 0-255 | CH3 0-10V |
CH4 0-255 | CH4 0-10V |
Stand-alone RGB/RGBW mode
-
Short press M key when display P01~P24 enter stand-alone RGB/RGBW mode.
-
Press ◀ or ▶ key to change dynamic mode number(P01~P24).
-
Each mode can adjust speed and brightness.
Long press M key for 2s prepare for setup mode speed, brightness, , W channel brightness.
Short press M key to switch three item.
Press ◀ or ▶ key to setup value of each item.
Mode speed:1-10 level speed(S-1, S-9, S-F).
Mode brightness:1-10 level brightness(b-1, b-9, b-F).
W channel brightness: 0-255 level brightness(400-4FF).
Long press M key for 2s, or timeout 10s, quit setting. -
Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost.
RGB change mode list
No. | Name | No. | Name | No. | Name |
---|---|---|---|---|---|
P01 | Static red | P09 | 7 color jump | P17 | Blue purple smooth |
P02 | Static green | P10 | Red fade in and out | P18 | Blue white smooth |
P03 | Static blue | P11 | Green fade in and out | P19 | RGB+W smooth |
P04 | Static yellow | P12 | Blue fade in and out | P20 | RGBW smooth |
P05 | Static cyan | P13 | White fade in and out | P21 | RGBY smooth |
P06 | Static purple | P14 | RGBW fade in and out | P22 | Yellow cyan purple smooth |
P07 | Static white | P15 | Red yellow smooth | P23 | RGB smooth |
P08 | RGB jump | P16 | Green cyan smooth | P24 | 6 color smooth |
Stand-alone dimmer mode
-
Short press M key, when display L-1~L-8, enter stand-alone dimmer mode.
-
Press ◀ or ▶ key to change dimmer mode number(L-1~L-8).
-
Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup four channel brightness.
Short press M key to switch four channel(100~1FF, 200~2FF, 300~3FF, 400~4FF).
Press ◀ or ▶ key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting. -
Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
Restore factory default parameter
- Long press ◀ and ▶ key for 2s, restore factory default parameter, display”RES”.
- Factory default parameter: DMX decode mode, DMX decode start address is 1, four channel decode, 0-10V output, linear brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
Dimming curve setting
Malfunctions analysis & troubleshooting
Malfunctions | Causes | Troubleshooting |
---|---|---|
No light | 1. No power. | |
2. Wrong connection or insecure. | 1. Check the power. |
2. Check the connection.
Wrong color| 1. Wrong connection of 0-10V output wires.
2. DMX decode address error.| 1. Reconnect 0-10V output wires.
2. Set corrrect decode address.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>