HAKKO FT-720 Automatic Tip Cleaner Instruction Manual
- June 13, 2024
- Hakko
Table of Contents
HAKKO FT-720 Automatic Tip Cleaner
Product Information
The HAKKO FT-720 is a rotating tip cleaner designed for cleaning soldering iron tips. It comes with an AC adapter and is equipped with electrostatic countermeasures. The product weighs 200g (0.44lb.) and has a brush rotational speed of 1670rpm.
Specifications
- Product: HAKKO FT-720
- Rating: 24 VDC 140 mA
- Brush rotational speed: 1670 rpm
- Dimensions: Not specified
- Weight: 200g (0.44lb.)
- AC Adapter Output voltage: 24 VDC
The product is designed for indoor use only and should not be used outdoors. It is important to use genuine HAKKO parts and not modify the product. The AC adapter included in the set should be used, and other AC adapters should not be used. Precautions should be taken to prevent the product from getting wet and to avoid handling it with wet hands. Additionally, any actions that may be considered dangerous should be avoided.
Product Usage Instructions
- Before using the HAKKO FT-720, read the instruction manual carefully.
- Confirm the contents of the package and ensure all parts are present.
- Ground the product before use.
- Install the solder waste collector before use.
- Attach the front cover and sensor cover before use.
- When carrying the cleaner, hold it by the base and not the AC adapter plug.
- When the product is not used for a long time, or before repairing or cleaning it, disconnect the AC adapter plug from the power outlet.
- When replacing parts, use only genuine HAKKO parts.
- When inserting and removing the plug, hold the plug body and do not pull the cord.
- Do not allow children to use, play with, clean, or perform user maintenance on this product without supervision.
To download the instruction manual in different languages, visit the HAKKO Document Portal. For further information and troubleshooting, visit the HAKKO website at https://www.hakko.com.
Contents and Part Names
Specifications
- HAKKO FT-720
Rating | 24 VDC 140 mA |
---|---|
Brush rotational speed |
1670 rpm
Dimensions| 67 (W) × 63 (H) × 94 (D) mm
(2.6 × 2.5 × 3.7 in.)
Weight| 200 g (0.44lb.)
- AC Adapter
- Output voltage 24 VDC
- T h i s p r o d u c t i s a p p l i e d w i t h electrostatic countermeasures.
- Please note that specifications and appearance are subject to change without notice in the interest of product improvement.
CAUTION
- Handling precautions for ESD Safe products This product contains electrostatic countermeasures, so please use the following precautions:
- Not all plastic parts are insulators, they may be conductive. Be careful not to expose live electrical parts or damage insulating materials when performing repairs or replacing parts.
- Be sure to ground the product before use.
Warnings, Cautions, and Notes
Warnings, cautions, and notes are placed at critical points in this manual to direct your attention to significant items. They are defined as follows:
- WARNING: Failure to comply with a WARNING may result in serious injury or death.
- CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved.
- Note: This indicates procedures or information that are important in a process described in this document. Be sure to observe the following precautions to ensure safety.
WARNING
- Those without the permission of a manager and those without the required experience or knowledge (including children) are not allowed to use this product.
- Do not allow children to play with this product.
- Do not allow children to clean or perform user maintenance without supervision.
Failure to observe the following precautions to ensure safety might result in electric shock, malfunction or other trouble.
CAUTION
- Before using this product, fully read all descriptions in this document.
- Do not use this product as an iron stand.
- Be sure to install the solder waste collector before use.
- Be sure to attach the front cover and sensor cover before use.
- When carrying the cleaner, carrying it by holding the base and not the AC adapter plug.
- This product is for indoor use only. Do not use it outdoors.
- When this product is not used for a long time, or before repairing or cleaning this product, disconnect the AC adapter plug from the power outlet.
- When replacing parts, use only genuine HAKKO parts.
- Use only the AC adapter that is included in the set. Do not use other AC adapters.
- Do not modify this product.
- When inserting and removing the plug, hold the plug body and do not pull the cord.
- Do not allow this product to get wet. Also, do not handle it with wet hands.
- Do not perform any other actions that may be considered dangerous.
Operation
- Insert the AC adapter plug in the DC jack.
- The sensor reacts when the tip is inserted and cleaning will begin.
Note Do not intentionally rotate the brush continuously.
Note Remove the adjuster when using a large tip. The adjuster can be
stored in the base.
Note This product cleans the tip in a short time. If the tip is left in
for a long time, it may accelerate deterioration of the tip or the cleaning
brush.
Note Place this product on grounded surface with electrostatic
measurement, or connect a wire to the ground screw upon use.
Maintenance
CAUTION
Regularly remove solder waste and flux residue that adhere to the solder waste
collector, cleaner interior, and cleaning brush
Note To remove the cover you must first remove the AC adapter plug from the DC jack.
- Removal of Solder Waste Remove the cover and remove solder waste
- Replacing the Brushes Replace the cleaning brushes by pulling them straight out of their brush fixing shafts.
- Tools are not required
- Cleaning the Sensor Cover Remove stains on the upper and lower recess areas of the front cover using a soft brush
Note If the sensor cover is considerably stained, remove the sensor cover
and clean it with alcohol damp cloth. In this case, be careful not to let
solder waste or other debris fall into the device.
Note Replace the sensor cover if it has cracked or there is a
considerable amount of scratches
Troubleshooting
When other problems occur or the above remedies do not resolve a problem, contact your nearest agent.
Replacement Parts****
Part No. | Part Name | Specifications |
---|---|---|
A5063 | Cleaning brush C | Fluoroplastic brush, qty 2 |
A5060 | Front cover | With sensor cover |
A5061 | Adjuster | |
A5062 | Sensor cover | qty 10 |
B5284 | Pulley belt | |
B3528 | AC adapter | Flat pin plug |
B5118 | AC adapter | Chinese plug |
B5119 | AC adapter | BS plug CE |
B5120 | AC adapter | European plug CE |
B5121 | AC adapter | Australian plug |
Options
Part No. | Part Name | Specifications |
---|---|---|
A1566 | Cleaning brush A | Plastic brush, qty 2 |
A1567 | Cleaning brush B | Metal brush, qty 2 |
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL : +81-6-6561-3225
FAX : +81-6-6561-8466
https://www.hakko.com
E-mail : sales@hakko.com
Please access the web address below for other distributors. https://www.hakko.com
References
- DOWNLOAD |HAKKO | HAKKO Corporation
- HAKKO Corporation - We respond to soldering needs throughout the world.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>