Endon 104108 Berenice 5 Light By Massive Lighting Instruction Manual

June 13, 2024
ENDON

Endon 104108 Berenice 5 Light By Massive Lighting

Product Information

The Pendant Light Fitting is designed for domestic ceiling use and is not suitable for bathroom locations. It is a Class I product that must be Earthed. The product is compatible with a 220-240V~ 50Hz power supply and should be installed in accordance with local building regulations and current IEE wiring regulations. The terminal blocks are supplied according to the requirements of the fitting.
It is important to note that nothing should be placed on the product or hung on any part of it. Bulbs with wattage higher than specified on the label should not be used as they may cause overheating and damage to the fitting.
For disposal, please do not throw away waste electrical products with household waste. Instead, recycle them where facilities exist. You can check with your Local Authority or local store for recycling advice.

Safety Warnings

  • Read the instructions thoroughly before use and keep them for future reference.
  • If you are unsure about installing the product, consult a qualified electrician.

Care and Maintenance

  • To replace the bulb, switch off the product and allow it to cool down before handling.
  • Clean the product with a dry cloth only. Do not use liquid or abrasive cleaners.

Troubleshooting

  • If the bulb does not light after installation, ensure there is no electricity failure and check that all connections are secure.
  • If you have any doubts about installation or use, consult a qualified electrician.

Assembly Instructions
Unfortunately, the provided information does not include the assembly instructions. Please refer to the product packaging or contact the manufacturer for detailed assembly instructions.

Manufacturer Information

  • UK Manufacturer: BH17 7BY
  • EU Manufacture r: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Installation and Safety Instructions
Pendant Light Fitting

Safety Warnings

  • These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician.

  • This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations, and should be installed in accordance with local building regulations. It is for domestic ceiling use only, and is not suitable for a bathroom location.

  • This is a Class l product and must be Earthed. The terminal blocks are supplied according to requirements
    of the fitting.

  • IMPORTANT: Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.

  • The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.

  • Decide on the position of the light fitting or remove existing light fitting. Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting.

  • Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.

  • Never put anything on the product or hang anything on any part of this product.

  • IMPORTANT: Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.

  • Never fit bulbs of a higher wattage than those specified on the label (as these may cause over heating and damage the fitting).

  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.

Troubleshooting

  • When the bulb does not light after installation
  • Ensure there is no electricity failure.

  • Ensure all the connections are secure.

  • If you have any doubt about installation/use of this product, consult a qualified electrician.

UK Manufacturer: BH17 7BY
EU Manufacturer : Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Assembly Instructions

Endon-104108-Berenice-5-Light-By-Massive-Lighting
\(1\)

Scan QR code for multi-language

UK Manufacture r: BH17 7BY
EU Manufacture r: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals