SUPERLIGHTINGLED BASICR2 WiFi Smart Switch User Manual
- May 15, 2024
- SuperLightingLED
Table of Contents
- Operating Instruction
- Compatible Pairing Mode
- Specifications
- Product Introduction
- Wi-Fi LED indicator status instruction
- Features
- RF Remote Controller Pairing
- Switch Network
- Factory Reset
- Common Problems
- CUSTOMER SUPPORT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SUPERLIGHTINGLED BASICR2 WiFi Smart Switch
Operating Instruction
Power off
To avoid electric shocks, please consult the dealer or a qualified professional for help when installing and repairing! Please do not touch the switch during use.
Wiring Instruction
Wiring: 16-1 SAWG SOL/STR copper conductor only, Tightening torque: 3.5
lb-in.
Make sure the neutral wire and live wire connection is correct.
To ensure the safety of your electrical installation, it’s essential either a
Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker
(RCBO) with an electrical rating of 1 0A has been installed before the
BASICR2, RFR2.
Download the eWelink APP
Power on
After powering on. the device will enter the quick pairing mode during the
first use. The Wi-Fi LED indicator changes in a cycle of two short and one
long flash and release.
The device will exit the quick pairing mode if not paired within 3mins. If you want to enter this mode, please long press the manual button for about Ss until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
Add the device
Tap”+” and select “Add Device”, then operate following the prompt on the App.
Compatible Pairing Mode
If you fail to enter Quick Pairing Mode, please try “Compatible Pairing Mode” to pair.
- Long press Pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode.
- Tap “+” and select “Add Device”, then operate following the prompt on the App.
Specifications
Model | BASICR2/RFR2 |
---|---|
Input | 100-240V AC 50/60Hz 1 OA |
Output | 100-240V AC 50/60Hz Max. Load: 1 OA |
Operating systems | Android & iOS |
Wi-Fi | IEEE 802.11 b/g/n 2.4GHz |
RF | 433,92MHz |
Material | PCVO |
Dimension | 88x39x24mm |
BASIC R2 does not support the remote controller with 433.92MHz.
Product Introduction
The device weight is less than 1 kg.
The installation height of less than 2 mis recommended.
Wi-Fi LED indicator status instruction
Wi-Fi LED indicator status | Status instruction |
---|---|
Flashes (one long and two short) | Quick Pairing Mode |
Keeps on | Device is connected successfully |
Flashes quickly | Compatible Pairing Mode |
Flashes quickly once | Unable to discover the router |
Flashes quickly twice | **Connect to the router but fail to connect to |
Wi-Fi
Flashes quickly three times**| Upgrading
Features
Turn on/off the device from anywhere, schedule power on/off and share APP with your family to control.
-
Remote Control
-
Single/Countdown Timing
-
Voice Control
-
Share Control
-
Smart Scene
-
Sync Status
-
433MHz Remote Control
-
Camera Linking
-
Power-on State
-
LAN Control
RF Remote Controller Pairing
The RFR2 supports the remote controller with 433.92 M Hz frequency brand to turn on/off, and each channel can learn it independently, which is local short-range wireless control not Wi-Fi control.
Pairing Method:
Long press the configuration button for 3s until the red LED indicator flashes
red once, then short press the remote control button you want to pair for
successful learning.
Clearing Method:
Long press the configuration button for 5s until the red LED indicator flashes
red twice, then short press the learned button corresponding to the remote
controller to clear code values of all learned buttons.
Switch Network
If you need to change the network, long press the pairing button for 5s until
the Wi-Fi LED indicator changes in a cycle of two short and one long flash and
release, then the device enters quick pairing mode and you can pair again.
Factory Reset
Deleting the device on the eWeLink app indicates you restore it to factory setting.
Common Problems
Q: Why my device stays “Offline”?
A: The newly added device needs 1 – 2mins to connect Wi-Fi and network. If it stays offline for a long time, please judge these problems by the green Wi-Fi indicator status:
-
The green Wi-Fi indicator quickly flashes once per second, which means that the switch failed to connect your Wi-Fi:
-
Maybe you have entered a wrong Wi-Fi password.
-
Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. Ifs failed, please add it again.
-
The SG Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
-
Maybe the MAC address filtering is open. Please turn it off.
If none of the above methods solved the problem, you can open the mobile data network on your phone to create a Wi-Fi hotspot, then add the device again. -
Green indicator quickly flashes twice per second, which means your device has connected to Wi-Fi but failed to connect to the server.
Ensure steady enough network. If double flash occurs frequently, which means you access an unsteady network, not a product problem. If the network is normal, try to turn off the power to restart the switch.
CUSTOMER SUPPORT
https://www.superlightingled.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>