joovy 220301 Big Caboose Graphite Triple Stroller Instruction Manual

: June 5, 2024
: Joovy

Table of Contents

Safety and Warnings
Parts List
Stroller Assembly
Care & Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OPEN & ASSEMBLE joovy 220301 Big Caboose Graphite Triple
Stroller

Instruction Manual
330X
© Joovy 2022 • 220301

Safety and Warnings

WARNING
Please read these instructions carefully before use and keep them for future reference.

Failure to follow these instructions could result in serious injury or death.
Never leave the child unattended.
Avoid serious injury from falling or sliding out.
Always use a restraint system and ensure that all children are positioned according to these instructions.
Be certain that the stroller is fully opened, BOTH safety latches are in position, and the wheel brakes are on before allowing children near the stroller.
The parking device should always be engaged during the loading and unlo
ading of children.
The front seats are not suitable for a child under 6 months.
The maximum weight of the child that can be seated in either forward-facing seat is 40 lbs. (18.2 kg).
The rear stand-on platform and the rear bench seat are designed for a child that is at least 2-1/2 years old but LESS than 44 in. (111.8 cm) tall and less than 45 lbs. (20.5 kg).
Use of the stroller with children totaling more than 125 lbs. (56.8 kg), will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition.
Never use this stroller to carry more than 3 children at the same time.
Never allow a child to step on the footrest to get into or out of the stroller.
Do not use the stroller on stairways or escalators.
Do not add any attachment not specifically recommended by Joovy.
Any load attached to the handle affects the stability of the stroller. Hanging purses, shopping bags, parcels, changing bags or other accessory items from handlebars or any other parts of the stroller may change the balance of the stroller and cause a hazardous unstable condition.
The maximum weight that can be carried in the storage basket is 15 lbs. (6.8 kg). Excessive weight may result in a hazardous unstable condition.
The included parent organizer is for use ONLY on the Joovy Big Caboose stroller. DO NOT use it on other stroller models.
Never carry hot beverages or open containers in the parent organizer. The maximum weight allowed is 5 lbs. (2.3 kg).
When installing an infant carrier onto the stroller, ALWAYS use the restraining strap to secure the carrier in place.
The maximum weight that can be carried in each cup holder is 2 lbs. (0.9 kg).
The maximum weight that can be carried in each seat side pocket is 1 lbs. (0.5 kg).
Never allow your stroller to be used as a toy.
Discard all packaging materials properly. Do not allow children to play with them.
Check your stroller for loose rivets, snaps, worn parts, and torn material or stitching on a regular basis.
Discontinue use of the stroller should it malfunction or become damaged.

Please do not return this product to the store.
If you experience any of difficulty with the assembly or use of this product, or if you have a question regarding these instructions, please contact Team 432 (page 12).
Please note: Styles and colors may vary.

Parts List

joovy 220301 Big Caboose Graphite Triple Stroller -
FIG

Additional Accessories (sold separately)
Customize your ride with a number of optional accessories for added functionality. All accessories are sold separately.
Rear Seat

Removable/machine-washable seat fabric

Stroller Assembly

IMPORTANT NOTE: Please refer to the end of this manual for all photos that are referenced in parentheses in the instructions below.
Unpacking the Product

Remove everything from the box – stroller, two canopies, two rear wheels, two front-wheel sets, parent organizer, tray, two Cup Holders, two infant car seat adapters, and documents (not shown).
Discard all packaging materials properly including plastic coverings.
DO NOT allow children to play with any packaging materials.

WARNING: Adult assembly is required for this product. No tools are required.

Unfolding

Keep children away from the stroller while unfolding.
Release the folding lock located on the right side by lifting the lever off of the catch. (1)
Lift up on the handle of the stroller until the frame snaps into its open locked position.
CAUTION: While unfolding the stroller, be careful to keep your fingers from being pinched by moving parts.
NOTE: Remove packing foam from rear frame assembly to ensure stroller locks in the open position.
Lock BOTH the safety latches on both sides of the stroller. (2)
Ensure that the safety latches are secured before ANY use of the stroller.

WARNING: ALWAYS secure the safety latches on BOTH sides of the stroller when it is in the unfolded use position. This will prevent collapse of the stroller should the handle trigger locks be accidentally opened. Possible pinching hazard – Be careful when unfolding the stroller.
Installing/Removing Rear Wheels

Install one rear wheel by sliding it onto the axle until it clicks into place. (3)
Repeat for another rear wheel.
Pull-on the wheels to ensure they are installed securely.
To remove each wheel, push up the plastic tab on the rear axle and then pull the wheel outward from the stroller. (4)

Installing/Removing the Front Wheels

Place the front wheel sets onto the front wheel posts until they click in place. (5)
Pull on the wheel sets to ensure they are installed securely.
To remove each wheel, press down on the plastic tab in the hole at the bottom of the front wheel and then pull the wheel outward from the stroller. (6)

Front Wheel Locks
The front wheels can be set to swivel or lock.

To lock the front wheels, rotate each wheelset so that it points forward.
Pull up on the locking lever to engage the swivel lock. (7)
To unlock the wheels (swivel mode) push down on the lever.

Installing and Operating the Canopies
These steps are for BOTH canopies.

Position the canopy with the padded edge forward.
Insert the canopy attachments into the frame mounts on BOTH sides. Ensure they snap into place. (8)
The canopy can be adjusted forward and back, and locked open using the canopy locks on BOTH sides. (9) and (10)
To close the canopy, unlock the sides, then collapse. (11)
To remove the canopy, press the lock buttons on BOTH sides of the canopy and pull up.(12)

WARNING: Possible pinching hazard – Be careful when closing and opening the side hinges so as not to pinch your fingers.
Attaching/Detaching the Front Tray

To attach the front tray, slide the tray onto BOTH mounts until they snap in place. (13)
To remove tray, press the lock buttons on BOTH mounts and pull forward. (14)

WARNING: The child tray is not a restraint device. Always secure your child with the restraint system. Never lift the stroller by the child tray. Use caution when attaching the child tray when there is a child seated in the stroller.
Attaching/Detaching the Cup Holders

To attach the Cup Holders, slide the Cup Holders onto the mount until they snap in place. (15)
To remove Cup Holders, press the lock buttons on the mount and pull forward. (16)

Stroller Operation
Rear Wheel Brakes

Always engage rear wheel brakes before placing a child in or removing a child from the stroller.
To engage, push down on the brake lever on either side. (17)
To release, push down on the back of the brake lever on either side. (18)
NOTE: Gently push the stroller back and forth to ensure the brake is fully engaged.

WARNING: Always engage the parking brake when the stroller is not being pushed so that it will not roll away. Never leave the stroller unattended, especially on a hill or incline, as the stroller may tip over or slide.
Adjusting the Footrest

The footrest can be adjusted to 3 positions.
To adjust it upwards, simply rotate it up to the desired position until it locks into place.
To adjust it down, press the release buttons on both sides and rotate it down to the desired position. (19)

WARNING: Never allow a child to step onto the footrest in either position in order to get into or out of the stroller. This may cause the stroller to tip over and injure the child.
Securing the Front Seated Children
These steps are for BOTH front-facing seats.

There are three height adjustment positions for the shoulder harness. Adjust the height to the closest height above your child’s shoulders.
To remove the shoulder harness, turn the plastic ends sideways and push them through the slots in the seatback. Reattach the harness at the proper height by reinserting the plastic ends through the slots. (20) Ensure both straps are the same height.
To remove the crotch strap, slide the strap through the small opening in the metal D-ring. Reattach by pushing the metal-D ring through the slot in the seat, wrap the strap around the tube under the seat bottom. Slide the strap through the small opening of the metal D-Ring and pull the strap to secure it to the tube. (21)
Remove the waist straps by sliding the strap through the small opening in the metal D-ring, then pull the strap away from the seat. (22) Reattach by pushing the metal-D ring through the slot in the seat, wrap the strap around the seat back frame tube. Slide the strap through the small opening of the metal D-Ring and pull the strap to secure it to the tube. Repeat for the other end of the strap.
To unlatch the buckle press the center button and remove the male ends of each buckle. (23)
Carefully place the child in the seat with the shoulder straps over their shoulders and chest. Then place the crotch strap between the child’s legs.
Push the shoulder/waist latch posts into the crotch buckle until all parts snap into place. (24)
Tighten the waist belt to be snug around the child’s waist.
The shoulder, waist, and crotch straps may be adjusted using the sliding plastic rings on these straps.

WARNING: The front seats are not suitable for a child under 6 months. Avoid serious injury from falling or sliding out. Always use the restraint system.

Seat Recline Positioning
The front seat has two positions. This seat should be used for children who are at least 6 months old. These steps are for BOTH front-facing seats.

To place the seat in the upright position, push the bar on the rear of the seat toward the front of the stroller and rotate the seatback towards the front of the stroller until this bar is locked in its lowest position. (25)
To recline the seat, pull the bar on the rear of the seat toward the rear of the stroller and rotate the seat back down until this bar is again in its lowest position. (25)

WARNING: Whether the seatback is upright or reclined, ALWAYS make certain that the recline mechanism is engaged before placing the child into the seat.

Using the Stand-On Platform

Push the bench seat to its most forward position.
Position the canopy to its most forward position.
Position the child on the platform on the back of the stroller. Be sure that the child is facing forward and BOTH of their hands are holding onto the stroller frame.
Be sure that BOTH of the child’s feet are fully on the platform at all times.
You may need to adjust the recline position of the seat to allow for more room for the child to stand.

WARNING: The rear stand-on platform and the rear bench seat are designed for a child that is at least 2½ years old but LESS than 44 inches (111.8 cm) tall and less than 45 lbs. (20.5 kg). Use of the stroller with 3 children totaling more than 125 lbs. (56.8 kg) will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition. NEVER allow a standing child to use the canopy as a handhold. NEVER use this stroller to carry more than 3 children at the same time.

Using the Rear Bench Seat

Push the bench seat to its most rearward position.
NOTE: There are webbing straps attached to the bottom of the rear seat pad. These straps will lock the seat into the most rearward position. To lock the seat, pull the straps from EACH side of the pad and loop them around the frame as shown, then snap them together. (26)
To slide the seat forward, undo EACH snap and reattach the webbing to the underside of the seat pad using the Velcro® attachments.
Position the canopy to its most forward position.
To unlatch the buckle press the center button and remove both latch posts.
Have the child sit on the bench seat facing backward with their feet on the platform.
You may need to adjust the recline position of the front seat to allow for more room for the child to sit.
Place the crotch strap between the child’s legs.
Push the waist latch posts into the crotch buckle until all parts snap into place. (27)
Adjust the waist straps to be snug around the child’s waist.
Be sure that BOTH of the child’s feet are fully on the platform at all times.
Be sure that BOTH of the child’s hands are holding the frame.

WARNING: NEVER allow a rear-seated child to use the canopy as a hand hold.
Storage Basket
The maximum weight that can be carried in the storage basket is 15 lbs. (6.8 kg).
Parent Organizer

Loop one strap of the parent organizer around one side of the handlebar and loop the rest of the strap back around the handlebar to attach the Velcro®. (28)
Repeat for the other side. Ensure the parent organizer is secure.

WARNING: For use ONLY on the Joovy Big Caboose Stroller. NEVER carry hot beverages or open containers in this product.
The maximum weight for an Organizer is 5 lbs. (2.3 kg).

Using the Stroller with Infant Car Seats
These steps are for BOTH front-facing seats. The Joovy Big Caboose will accommodate a car seat in EACH of the front seats.
NOTE: See insert for a list of specific compatible car seat models.

Remove the front tray and the front canopy. Install the infant car seat adapter in the front tray mounts. Ensure it is secure on BOTH sides. (29)
ADJUST THE SEAT TO ITS RECLINE POSITION.
Remove the infant car seat from its base and place it onto the front seat of the stroller so it is in a REAR FACING POSITION. Position the “head” end toward the front, resting on the infant car seat adapter. Position the “feet” end on the seatback – but NOT on the top edge of the seatback. (30)
Buckle the restraining straps over the LOWEST part of the infant car seat (the straps are located in the pockets on the side of the seat). Adjust the straps so they are tight around the infant car seat but AWAY from the child’s neck. Pull up on the infant car seat to be sure it is secure. (31)
To remove the infant car seat from the stroller, unlock the restraining strap buckle by pressing the button and both side releases. (32)
Return the restraining straps to their pockets.

WARNING: ALWAYS install the infant car seat so that the child is facing toward the rear (handle) of the stroller with the restraining straps secured. ALWAYS position the infant car seat so that it is securely placed down inside the infant car seat adapter frame. ALWAYS position the infant car seat so that it is resting ON the seatback, but NOT on the top of the seatback. The seatback must be in the RECLINE position. NEVER position the restraining straps on or near the child’s neck as this may result in strangulation. The infant car seat adapter is for use ONLY with specific infant car seat models. See insert for specific models. DO NOT use other infant car seat models.
Folding the Stroller

Keep children away from the stroller while folding.
Remove any infant car seat. The stroller can be folded with the infant car seat adapter in place.
Close BOTH canopies and push it forward.
Put the front seats into their most upright position.
Make sure both rear wheel brakes are set to their locked positions.
Lock BOTH front wheelsets in place with locking levers facing forward.
Unlock the safety latches on the BOTH sides of the stroller.
Pull upward on the trigger mechanisms on both sides of the stroller and push the handle fully forward. (33)
CAUTION: While folding the stroller, be careful to keep your fingers from being pinched by moving parts.
Engage the fold lock on the right side of the stroller over the mounting post. (34)

WARNING: ALWAYS keep children away from the stroller when folding. Possible pinching hazard – Be careful when folding the stroller.

Care & Maintenance

Maintenance
All of the fittings, snaps, locks, rivets, and other hardware and plastic parts on the stroller should be inspected periodically to ensure that they are secured properly and not damaged or malfunctioning. The safety harness, as well as all other straps and fabric items and their stitching, should also be inspected periodically to ensure that they are secured properly and not loose, torn or otherwise damaged. All moving parts, such as wheels, brakes, and hinges should also be checked periodically to ensure they are operating properly. Any missing, broken, or worn components should be replaced immediately, and the playard should not be used until they are replaced. Only original manufacturer’s components should be used. If needed, please contact Joovy at our toll-free phone number.
Cleaning
The fabric material on this stroller can be cleaned using mild household soap or detergent and warm water on a sponge or clean cloth. Always allow the fabric to completely air dry before using the stroller.
The frame and wheels should always be kept clean and free of dirt and foreign matter, especially after operating the stroller in rain, snow, or other harsh environments. Use a sponge or cloth dampened with warm water and a mild household soap or detergent to clean the wheels after such use.
Storage
Direct sunlight may fade fabric and dry out wheels. Store stroller indoors to prolong its appearance.
DO NOT store outdoors. Ensure that the stroller is dry before storing for prolonged periods. Always store the stroller in a dry environment. Store the stroller in a safe place when not in use (i.e. away from children). DO NOT place heavy objects on top of the stroller. DO NOT store the stroller near a direct heat source such as a radiator or open fire.
Team 432
Please do not return this product to the store.
If you experience any of difficulty with the assembly or use of this product, or if you have a question regarding these instructions, please contact Team 432:
United States
Joovy 877-456-5049, 8:30 am – 5:00 pm Central Time
joovy.com LiveChat, 8:30 am – 9:00 pm Central Time customerservice@joovy.com
@joovy
Canada
Elfe Juvenile Products
800-667-8184, 8:30 am – 5:00 pm Eastern Time service@elfe.ca